Speaker
Microphone
RINS1399-1
Speech Dialler with Automation Control
USER MANUAL
User Manual V2 TEL
Pyronix Ltd Page: 2
EASY START GUIDE
Enter 1 2 3 4
This enters the user menu.
Enter 9 0 1
Program telephone number 1.
Repeat for all other numbers if
required [901-909].
Enter 9 3 1
Program the message types for the
telephone numbers. Repeat for all
other numbers if required [931-939].
Enter 999
Press the t key to exit the user
mode.
V2 TEL User Manual
Page: 3 Pyronix Ltd
CHAPTER 1: CONTENTS PAGE
CHAPTER 1: CONTENTS PAGE..............................................................................3
CHAPTER 2: INTRODUCTION .................................................................................4
CHAPTER 3: HOW THE V2 TEL WORKS................................................................5
3.1 THE V2 TEL PROCESS.................................................................................................5
CHAPTER 4: OPERATING THE KEYPAD................................................................6
4.1 SCROLLING THROUGH MAIN MENUS............................................................................6
4.1.1 Scrolling through main menu ...............................................................................6
4.1.2 Scrolling through sub menu .................................................................................7
4.1.3 Entering a sub menu/main menu function............................................................7
4.2 ENTERING TELEPHONE NUMBERS..................................................................................7
CHAPTER 5: THE USER MENU...............................................................................9
5.1 ENTERING THE USER MENU...........................................................................................9
5.2 EXITING THE USER MENU...........................................................................................9
5.3 CALL TELEPHONE NUMBER [600]...............................................................................10
5.4 ACTIVATING THE ON BOARD 4 OUTPUTS..................................................................10
5.5 ADDITIONAL OUTPUT CONTROL [700].........................................................................11
5.6 PLAY / RECORD ALARM VOICE MESSAGES [800]......................................................11
5.7 PLAY / RECORD COMMON MESSAGE [820] ........................................................12
5.8 PROGRAM TELEPHONE NUMBERS [900]............................................................12
5.9 MESSAGE TYPE [930] ................................................................................................13
5.10 CALL ACKNOWLEDGEMENT CODE [960]...................................................................14
5.11 COPY ACKNOWLEDGEMENT CODE 1 TO ALL [980]...................................................14
5.12 ENABLE REMOTE LISTEN-IN [984]............................................................................15
5.13 VIEW EVENT LOG [985]............................................................................................15
5.14 CHANGE USER CODE [986]......................................................................................15
CHAPTER 6: RECEIVING A CALL FROM THE V2 TEL ........................................16
CHAPTER 7: REMOTE CONTROL VOICE MENU .................................................17
CHAPTER 8: SHORTCUT FUNCTION REFERENCE ............................................18
CHAPTER 9: INPUTS/OUTPUTS APPENDIX ........................................................18
9.1 INPUTS.......................................................................................................................18
9.2 OUTPUTS...................................................................................................................18
User Manual V2 TEL
Pyronix Ltd Page: 4
CHAPTER 2: INTRODUCTION
The V2 TEL is 2 way TEL audio communication and remote automation module.
The V2 TEL has the following features:
Call any telephone number (just like a mobile phone)
Supports 2 way speech via the built on speaker and microphone
Activate outputs (to turn on lights, open gates, etc)
o Locally via the integrated keypad
o Remotely via voice menu command
Program voice messages (Up to 6, 1 for each alarm input)
Send voice alerts to up to 9 different user phone numbers
View the V2 event log (256 events)
Remotely by phone operate the V2 using the built in voice menu:
o Listen in
o Talk
o Control output
o Check the status of an external device that is connected to the V2 (for
example system armed or disarmed)
V2 TEL User Manual
Page: 5 Pyronix Ltd
CHAPTER 3: HOW THE V2 TEL WORKS
3.1 THE V2 TEL PROCESS
Below shows a flowchart that is a representation of how the V2 TEL operates, when alarm
activation occurs.
User Manual V2 TEL
Pyronix Ltd Page: 6
CHAPTER 4: OPERATING THE KEYPAD
The V2 TEL keypad incorporates 4 output status LEDs positioned above the LCD display.
They are numbered 1 to 4 and are used to show the status of the 4 inbuilt outputs.
4.1 SCROLLING THROUGH MAIN MENUS
4.1.1 Scrolling through main menu
TO SCROLL THROUGH MAIN MENUS. PRESS THE [ AND ] KEYS
MAIN MENU ITEMS ARE IN CAPITAL LETTERS
V2 TEL User Manual
Page: 7 Pyronix Ltd
4.1.2 Scrolling through sub menu
TO SCROLL THROUGH SUB MENUS. PRESS THE M AND N KEYS
SUB MENU ITEMS ARE IN CAPITAL LETTERS
4.1.3 Entering a sub menu/main menu function
TO ENTER ANY FUNCTION. PRESS THE t KEY
Press x to exit a sub-menu, and to go back to the main menu functions, press x
until a main menu function (in capital letters) is displayed. Function numbers can be
entered to jump to a particular menu. For example to leave the V2 TEL from any main
menu or sub-menu digit [999] that will bring you to ‘QUIT/EXIT PROGRAMMING’.
4.2 ENTERING TELEPHONE NUMBERS
The numeric keys above are used to enter telephone numbers and symbols onto the V2
TEL that may need to be used for international dialling.
User Manual V2 TEL
Pyronix Ltd Page: 8
Keys Operation Example Display
t
Enters a function / starts a
command
x
Exits a function / stops a
command
I
Activates output 1
J
Activates output 2
K
Activates output 3
L
Activates output 4
Deletes the current number that
the cursor is on
N
Scrolls between sub-menu items
M
Scrolls between sub-menu items
[
Scrolls between main-menu
items
]
Scrolls between main-menu
items
V2 TEL User Manual
Page: 9 Pyronix Ltd
CHAPTER 5: THE USER MENU
5.1 ENTERING THE USER MENU
Using the keypad enter the user
code.
Default = 1234
‘[600] CALL TELEPHONE NUMBER’
will be displayed which indicates you
are in the user menu.
Use the [ and ] keys to scroll
through the main menus.
Press t to enter a function.
NOTE: If the display shows ‘USER PROG. REQ.’, this means that no telephone numbers
or voice messages have been programmed in the user menu.
5.2 EXITING THE USER MENU
To exit the user menu, type in ‘999’ or
scroll to
“QUIT / EXIT PROGRAMMING”
Press the t key.
NOTE: When exiting the V2 TEL user menu, the display may show the following:
Voice messages and phone numbers will need to be programmed before exiting the user
menu.
User Manual V2 TEL
Pyronix Ltd Page: 10
5.3 CALL TELEPHONE NUMBER [600]
This function allows the user to make an outgoing call. Enter the telephone number you
would like to call and press t
Press the [ or ] keys to scroll to
‘CALL TELEPHONE NUMBER’ or
enter ‘600’. Press t
Enter the telephone number to dial
and press t. Press x to end the
call.
During the call you can increase or
decrease the volume by using the
up/down arrow keys.
5.4 ACTIVATING THE ON BOARD 4 OUTPUTS
To activate the 4 onboard outputs there is no need to enter the user menu. They can be
activated / deactivated by pressing the required number key for 2 sec:
Press and hold I to activate output 1.
The LED 1 output will illuminate. Press
and hold I to deactivate output 1.
Press and hold J to activate output 2.
The LED 2 output will illuminate. Press
and hold J to deactivate output 2.
Press and hold K to activate output 3.
The LED 3 output will illuminate. Press
and hold K to deactivate output 3.
Press and hold L to activate output 4.
The LED 4 output will illuminate. Press
and hold L to deactivate output 4.
V2 TEL User Manual
Page: 11 Pyronix Ltd
5.5 ADDITIONAL OUTPUT CONTROL [700]
The V2 TEL comes with 4 already built in outputs.
Press the [ or ] keys to scroll to
‘OUTPUT CONTROL’ or enter ‘[700]’.
Press t
Press M or N to select the PGM
number (up to 52) Press t
Press M or N to turn the output on
or off or select the number:
0 = Output off (default)
1 = Output on
Press t
700 – 704 for the on board V2 TEL outputs.
5.6 PLAY / RECORD ALARM VOICE MESSAGES [800]
Voice messages can be programmed for each input on the V2 TEL. The voice alarm
messages can be up to 12 sec long. At default there are no user recordings.
Press the [ or ] keys to scroll to
‘PLAY/REC ALARM VOICE
MESSAGES’ or enter ‘800’. Press
t
Press M or N to select which input
number (or enter the shortcut function
number see page 11) Press t
Press:
1 = To play a message
4 = To record
9 = To delete
Shortcut Function Numbers:
INPUTS BUILT IN V2TEL
801: Play/rec msg for input#1
802: Play/rec msg for input#2
803: Play/rec msg for input#3
804: Play/rec msg for input#4
805: Play/rec msg for input#5
806: Play/rec msg for input#6
User Manual V2 TEL
Pyronix Ltd Page: 12
5.7 PLAY / RECORD COMMON MESSAGE [820]
This message is played each time activation has occurred and is heard at the end of an
input activation message. The common message can be 20 seconds long.
Press the [ or ] keys to scroll to
‘PLAY/REC COMMON MESSAGE’ or
enter ‘820’.
Press t
Press:
1 = To play a message
4 = To record
9 = To delete
Press t
5.8 PROGRAM TELEPHONE NUMBERS [900]
Up to 9 telephone numbers can be programmed on the V2 TEL. Your Engineer will have
already assigned the desired alarm messages to one or more telephone numbers.
The V2 TEL will support up to 14 Voice messages. One for each alarm input.
Press the [ or ] keys to scroll to
‘PROGRAM TELEPHONE
NUMBERS’ or enter ‘900’.
Press t
Press M or N to select which
telephone number to be programmed
(or enter the shortcut function
number).
Press t
Enter the telephone number and
press t
If dialling abroad, use the I key to
enter a ‘+’ symbol.
Menu Shortcut Function Numbers:
901: telephone number #1
902: telephone number #2
903: telephone number #3
904: telephone number #4
905: telephone number #5
906: telephone number #6
907: telephone number #7
908: telephone number #8
909: telephone number #9
V2 TEL User Manual
Page: 13 Pyronix Ltd
5.9 MESSAGE TYPE [930]
This function allows the choice of what message type is sent for each telephone number.
The following different message types can be programmed:
Voice: Sends a voice message only (example: ALARM, ALARM, ALARM).
Voice + Common: Sends a voice message and common message (example: ALARM,
ALARM, ALARM. This is Mr and Mrs Jones of West Street).
Press the [ or ] keys to scroll to
‘MESSAGE TYPE’ or enter ‘930’.
Press t
Press M or N to select which
message type for which telephone
number needs to be programmed (or
enter the programmed function
number).
Press t
Press M or N to select which
message type or select the number:
0 = Voice = Default
1 = Voice + common
Press t
Menu Shortcut Function Numbers:
931: Message type for tel#1
932: Message type for tel#2
933: Message type for tel#3
934: Message type for tel#4
935: Message type for tel#5
936: Message type for tel#6
937: Message type for tel#7
938: Message type for tel#8
939: Message type for tel#9
User Manual V2 TEL
Pyronix Ltd Page: 14
5.10 CALL ACKNOWLEDGEMENT CODE [960]
When the V2 TEL calls a telephone number, the relevant message will be played. At the
end of the message the V2 TEL will ask you to enter a code number to acknowledge that
the message has been received. If the call is not acknowledged then the V2 TEL will
make a repeat call.
This code is programmable and can be anything from up to 1 to 10 digits long.
Press the [ or ] keys to scroll to
‘CALL ACKNOWLEDGE CODE’ or
enter ‘960’. Press t
Press M or N to select the call
acknowledgement code for the
telephone number (or enter the
programmed function number).
Press t
Enter the code.
Press t
Default = 5.
Menu Shortcut Function Numbers:
961: Call ack. code for tel:1 966: Call ack. code for tel:6
962: Call ack. code for tel:2 967: Call ack. code for tel:7
963: Call ack. code for tel:3 968: Call ack. code for tel:8
964: Call ack. code for tel:4 969: Call ack. code for tel:9
965: Call ack. code for tel:5
5.11 COPY ACKNOWLEDGEMENT CODE 1 TO ALL [980]
This function supplies a shortcut to copy the acknowledgement code programmed in
telephone number 1 (function 961) to all 8 other telephone numbers.
Press the [ or ] keys to scroll to
‘COPY ACK CODE 1 TO ALL’ or
enter ‘980’.
Press t
Press M or N to select the Yes or
No or select the number:
0 = No = Default
1 = Yes
Press t
V2 TEL User Manual
Page: 15 Pyronix Ltd
5.12 ENABLE REMOTE LISTEN-IN [984]
Press the [ or ] keys to scroll to
‘ENABLE REMOTE LISTEN-IN’ or
enter ‘984’.
Press t
Press M or N to select the Yes or
No to select the number below to
enable remote listen in:
0 = No
1 = Yes = Default
Press t
5.13 VIEW EVENT LOG [985]
All events that occur are recorded in the event log. The V2 TEL display will show all
information in order, starting at the most recent event.
The above display shows the following:
001 = Event number (up to 256 events can be logged)
Description of event logged.
Press the [ or ] keys to scroll to
‘VIEW EVENT LOG’ or enter ‘985’.
Press t
Press M or N to scroll back and
forth through the log. Press the ]
key to jump to the last event.
Press x to exit.
5.14 CHANGE USER CODE [986]
The user code can be up to 4 digits.
Press the [ or ] keys to scroll to
‘CHANGE USER CODE’ or enter
‘986’.
Press t
Enter the new user code,
press t
Default user code = 1234
User Manual V2 TEL
Pyronix Ltd Page: 16
CHAPTER 6: RECEIVING A CALL FROM THE V2 TEL
After alarm activation has occurred, the V2 TEL will call one or more of
the programmed telephone numbers.
Voice Alarm Transmission:
V2 TEL dials the programmed telephone number
The user answers the call
Voice Alarm Message is played
V2 TEL will ask for call acknowledgement code
The user will enter the required acknowledgement code to
acknowledge the call
A long beep is heard and the call will be finished
At the end of the long beep, If the ‘9’ key is pressed twice (99) a
remote control menu is entered (if enabled by the engineer).
V2 TEL User Manual
Page: 17 Pyronix Ltd
CHAPTER 7: REMOTE CONTROL VOICE MENU
The V2 TEL remote control menu can be accessed in two different ways:
Method 1:
After acknowledging an alarm call at the end of the long beep, If the ‘9’ key is pressed
twice (99) the remote control menu is entered (if enabled by the engineer).
Method 2:
Call the V2 TEL telephone number. After a pre-programmed number of rings the V2 TEL
will answer-
The V2 TEL voice menu will ask you:
Enter your user code. This is the same code that is used to enter the user
menu on the V2 TEL.
After entering a valid user code the V2 TEL voice menu will say:
Enter your command number or press ‘9’ for help. The command
numbers available on the V2 TEL are as follows:
Press 1 = listen
Press 2 = talk
Press 3 = control output
Press 4 = system status
Press 0 = to hang up.
If you press 9 for help the following messages will be played:
Press 1 to listen, 2 to talk, 3 to control output, 4 for system status or
press 0 to hang up.
If you decided to control an output, press 3. The voice menu on V2 TEL will say:
Enter the output number. Enter the output that you wish to operate, 1 to 4
for the built in outputs (see the output appendix on page 18).
After choosing an output to control, the voice menu on V2 TEL will say:
Press ‘1’ to turn on, ‘0’ to turn off. This turns on and off the chosen
output.
If you decided to check the external system status, press “4” key. The V2 TEL will
say:
Armed or Disarmed. This function needs to be enabled by the Engineer.
To exit the V2 TEL voice menu press “0” key. The voice menu will say:
‘Goodbye’
User Manual V2 TEL
Pyronix Ltd Page: 18
CHAPTER 8: SHORTCUT FUNCTION REFERENCE
600 CALL TELEPHONE NUMBER
700 OUTPUT CONTROL
701-704 PGM#1 output control [701]… - 4 on board outputs
800 PLAY/REC ALARM VOICE MESSAGES
801-806 Play/rec msg for input #1[801] … -6 onboard inputs
820 PLAY/REC COMMON MESSAGES
820 Play/rec common message[820]
900 PROGRAM TELEPHONE NUMBERS
901-909 Telephone number #1 [901], Telephone number #2 [902] …
930 MESSAGE TYPE
931-939 Message type for tel#1 [931], Message type for tel#2 [932], …
960 CALL ACKNOWLEDGE CODE
961-969 Call ack. code for tel: 1 [961], Call ack. code for tel#2 [962] …
980 COPY ACKNOWLEDGEMENT CODE 1 TO ALL
984 ENABLE REMOTE LISTEN-IN
985 VIEW EVENT LOG
986 CHANGE USER CODE
999 QUIT/EXIT PROGRAMMING
CHAPTER 9: INPUTS/OUTPUTS APPENDIX
This section should be filled in by the engineer who installed the system.
9.1 INPUTS
Inputs Description Inputs Description
1 (onboard)
4 (onboard)
2 (onboard)
5 (onboard)
3 (onboard)
6 (onboard)
9.2 OUTPUTS
Outputs Description Outputs Description
1 (onboard)
3 (onboard)
2 (onboard)
4 (onboard)
V2 TEL User Manual
Page: 19 Pyronix Ltd
Secure Holdings
Pyronix House
Braithwell Way
Hellaby
Rotherham
S66 8QY
Website: www.pyronix.com
Loading...