Pyronix KX10DP-WE User Manual

KX10DP-WE

®

10m Wireless PIR Detector

KX10DP-WE Specifications

Model:

Colour:

Casing:

Transmission Frequency:

Tranmission Method:

Transmission Range:

Detection Method:

Sensitivity:

Temperature Compensation:

Detection Range:

Detection Zones:

Detection Speed:

Detection Angle:

Battery:

Battery Life:

Mounting Height:

Nominal Mounting Height:

Tamper Switch:

Storage Temperature:

Operating Temperature:

Accessories:

Emissions:

Immunity:

®

KX10DP-WE 10m Internal detector

WHITE

3mmABS, 0.4mm HDPE in LensArea

868MHz, FMTransceiver Narrow Band

Fully Encrypted Rolling Code

300m Free Space

Low Noise Pyroelectric Sensor

High, Low

AdvancedAutomatic

10m

74

0.3 - 3.0 m/s

85

CR123A Lithium Battery

Greater than 2 years

2m to 2.8m

2.4m

Front + Optional RearTamper

-20 C to 50 C

-10 C to 50 C

Wall and ceiling mounting brackets optional

EN55022 Class B

EN50130-4

®

Coverage Pattern

Horizontal Coverage

m01

9m

8m

7m

6m

5m

4m

3m

2m

m1

2m

3m 4m

Vertical Coverage

2.4m

1m

2m

1m

3m 4m

5m 6m 7m

5m 6m 7m

9m

8m

O

85
74 zones
7 planes

m01m1

9m

8m

10m

The detector will tolerate animals
of up to 20kg when the height of
the animal is less than 1 metre.

This product is approved for use in the Residential,

Commercial and Light Industrial Environment.

EN50131-2-2:2008
EN50131-5-3:2005

2

Security Grade 2
Environmental Class II

Customer Support Line : [phone]

Pyronix Limited, Secure House, Braithwell Way,

This product is sold subject to our standard warranty

conditions and is warranted against defects in

workmanship for a period of two years

In the interest of continuing improvement of quality,

customer care and design, Pyronix Ltd reserves the

right to amend specifications, without giving prior

or telephone [phone]

E-mail: [e-mail]

website: www.pyronix.com

Hellaby, Rotherham, S66 8QY. UK

WARRANTY

excluded)

(batteries

notice.

RINS1421-1

.

Installation Wall Mounting

CASE LID

SCREW FITTING

NOTE: When mounting the
detector, ensure that it is
not tilting backwards.

Optional Bracket Fitting Dimensions Avoiding False Alarms

Wall Ceiling

Part number: FPKXBRACKET

3mm
(0.12")

69mm
(2.72”)

= 105g (3.4 oz) without bracket

Kg

50mm
(2.2”)

117mm
(4.61”)

1. The detector will tolerate animals of up to
20kg when the height of the animal is less
than 1 metre.

2. Do not install the detector looking at stairs.

3. Avoid placing the detector in direct sunlight.

4. Do not mount the detector near heaters or

radiators.

5. Do not mount the detector near open
windows or air vents.

6. Mount the detector on a stable surface.

The KX12DW-WE Printed Circuit Board

Header for Rear Tamper

Battery

Tamper Spring

Pet mirror must
not be removed

DIGITAL SIGNAL
PROCESSING SELECT

SENSITIVITY

Header On

= HIGH)

Header Off

= LOW

Sensitivity Settings

+

-

Learn Button

Piro Sensor

DO NOT TOUCH

Learning the KX12DW-WE onto the Enforcer Control Panel

When you are ready to learn the device to the
control panel receiving equipment, and when the
equipment is in the learn mode (see Enforcer
Programming Manual) follow the procedure
below.

1. Make sure the battery is installed correctly
and the plastic wrapping removed.

2. Press and Hold the Learn button until the
3 LEDs start cycling through the different
colours, then release the Learn button.

3. The device is correctly learnt when the
Green LED flashes.

The three coloured LEDs give a
visual indication of the signal
strength.

Green indicates good signal strength
and is a good location to install.

Red indicates poor signal
strength and the device should not
be installed in that position.

If no LED illuminates then the device
is completely out of range.

The batteries supplied have been chosen to

provide long service life whilst, for safety

reasons, having limited output current.

Replace only with approved batteries.

To prevent possible damage to components,

any static charge on your body needs to be
eliminated before touching the inside of the
unit. This can be accomplished by touching
some grounded/earthed metallic conductor

such as a radiator/pipework immediately

before replacing the batteries.

RED BLUE GREEN

RED BLUE GREEN

RED BLUE GREEN

RED BLUE GREEN

Changing The Battery

REAR TAMPER

CR123A
LITHIUM

+

BATTERY

The blue LED will illuminate
when the device is activated.

-

mralA

NVM RESET

CR123A
LITHIUM

+

BATTERY

RED BLUE GREEN

-

RINS1421-1