Page 1
Quick Start Guide
TTEZ
User Guide available at pyramidtimesystems.com
Guía del usuario disponible en pyramidtimesystems.com
Guide de l’utilisateur disponible à pyramidtimesystems.com
Page 2
What you will need.
Tape Measure Pencil Phillips Head
Screw Driver
Power Drill
(Optional)
TTEZ Terminal
TimeTrax™
Swipe Cards (25)
Part #41302
TIMETRAX™
Software CD
RJ45 Cable
Mounting
Hardware
TTEZ Quick Start
Guide &
TTEZ Series Software
Reference Guide
RJ45/USB
Connector
Security Bracket
& Key
Contents
Quick Start Guide
pyramidtimesystems.com
pyramidtimesystems.com
MODELS TTEZ, TTEZEK, TTEZPROXEK (PPDLAUBKN)
Software Reference Guide
Power
Supply
M
e
r
i
d
e
n
,
C
T
U
S
A
:
8
8
8
.
4
7
9
.
7
2
6
4
:
©
2
0
1
6
:
P
y
r
a
m
i
d
T
i
m
e
S
y
s
t
e
m
s
,
L
L
C
:
A
l
l
R
i
g
h
t
s
R
e
s
e
r
v
e
d
.
:
4
2
7
8
2
R
e
v
.
B
Page 3
IMPORTANT:
Please write down serial #
located on back of terminal
before mounting.
Write your serial # here:
SAMPLE
Software Requirements
Single User installation,
Windows 7 or above
All Windows updates must be installed
prior to software installation
Regional settings & hardware
input in English
English
TM
TimeTrax™ Time & Attendance software should not
be installed on server PC’s.Pyramid Time Systems
does not support the use of TimeTrax™ software
on a server PC. For Multi User Upgrade, call
888.479.7264 Ext. 1.
Page 4
6
3
7
1
Connect & Mount Terminal
To mount terminal.
bottom of bracket should be approximately 45
Level bracket & mark four screw holes close to
corner tabs.
Drill holes as marked and insert included anchors
if needed.
Screw mounting bracket to wall with included
screws.
Drill hole centered in rectangular opening of
bracket for cables. The hole should be large
enough to route cables through wall.
Push terminal onto mounting bracket aligning
four tabs on bracket with four matching slots on
back of terminal. Be sure to write down the
terminal serial number before mounting.
Slide terminal downward until locking tab clicks
into place. When properly mounted, terminal
cannot be slid up and off bracket without using
included wall bracket release key to disengage
locking tab.
To detach terminal.
Hold wall bracket release key with pointed end
up & diagonally cut side away from you.
Insert key into narrow slot located on bottom of
terminal to rig
ht of cable access cutout.
Push key all the way up into slot. Key will slide
easily until last ½ inch until some resistance from
locking tab is felt.
With key fully pushed into slot, slide the terminal
up and off mounting bracket.
Connect the RJ45 cable into USB port
located on the back of terminal.
Connect the RJ45/USB Connector to the
free end of RJ45 cable
.
Connect power supply into power port
located in compartment on back of
terminal.
Route the cables through channel at base
of terminal.
Mount terminal (see instructions below).
Plug free end of RJ45/USB Connector into
network jack, router or switch.
Plug free end of power supply into
outlet.
1
2
3
4
5
6
5
4
2
7
Page 5
Insert TimeTrax™ DVD into CD-ROM drive.
Run Install Wizard and click “Finish” when
installation is complete.
Enter Login ID “ADMIN”.
Enter Password “PTI” (case sensitive).
Click “LOGIN”.
LOGIN
Please login with your Login ID and Password.
Login ID *
* Required Fields
Password*
ADMIN
LOGIN
1
2
1
Click on “Company” from the “Setup” drop down menu.
(*) then click “Save & Close”.
Setup
Install TimeTrax™ Software
Password may be changed after Setup is complete by clicking Administration/User Accounts from tool bar.
Page 6
Start time should be one hour after last Out punch of previous iod.
2
Click “Pay Class” from the “Setup” drop down menu. A default Pay Class has been set up. Click “Edit” to
review all settings. Click “Save & Close”. If additional Pay Classes are needed, click “Add Pay Class” and
“Save & Close”.
Setup Cont.
3
Click “Employee Group” from the “Setup” drop down menu. Click “Add Employee Group” and complete
Page 7
Swipe card in the swipe channel from top to
bottom.
If employee card number is successfully read, the
time clock terminal will beep and the card num-
Employee punches generated from swipe card
are stored within the terminal. The terminal
stores the last 6,000 punches before download is
required. Depending upon usage, punches can be
retrieved on a more or less frequent basis.
Using Time Clock
Setup Cont.
4
Click “Pay Class” from “Setup” drop down menu. A default Pay Class has
been set up. Click “Edit” to choose your settings. Click “Save & Close”.
If additional Pay Classes are needed, click “Add Pay Class” and complete
“Save & Close”.
It is very important that this information is correct before you continue.
Page 8
Copyright © 2017 Pyramid Time Systems. All rights reserved.
I2206 Rev. I
Chat online
pyramidtimesystems.com
Call us
888.479.7264 EXT 1
Send us an email
customersupport@ptitime.com
Loading...