Pyle view PLMD8 Installation Manual
PLMD8
Installation
FMStereo
M
odulator
FMStereo
M
odulator
WIRING CONNECTION
ToDVD player
RCA Line Output
White
Red
+12v Power
Car Antenna
ToAntenna Jack
Off
On
Wor.2
FM StereoModulator
R
INSTRUCTION MANUAL
BEFORE INSTALLING THE MODULATOR
INSTALLATION
FM RADIO FREQUENCY PRESET
PLL FM Stereo Modulator
1. Do not install the unitin the following locations.
Locations exposed to direct sunlight.Locations exposed to direct sunlight.
Where hot air is discharged from the car heater.Where hot air is discharged from the car heater.
In areas subject to extremetemperatures.In areas subject to extremetemperatures.
2. Be careful not damage thecar wiring.
3. Be sure to use the supplied screws.
The FM Stereo Modulator mustbe mounted within 24inches of your radio so
that its power cable can reach the radio power antenna lead.It can be fixed to
any flat surface behind theinstrument panel with two 3mm taping screws.
The FM Stereo Modulator mustbe mounted within 24inches of your radio so
that its power cable can reach the radio power antenna lead.It can be fixed to
any flat surface behind theinstrument panel with two 3mm taping screws.
Yourfinal choice of location should allow for the insertion or removal of the
Cable from the FM StereoModulator Unit.
Also,the FM Station Frequency SelectorSwitch is located on the side and you
may wish to change itafter your initial checkout or somtime in the future.
Yourfinal choice of location should allow for the insertion or removal of the
Cable from the FM StereoModulator Unit.
Also,the FM Station Frequency SelectorSwitch is located on the side and you
may wish to change itafter your initial checkout or somtime in the future.
The FM Stereo Modulator canoperate on from 87.7MHz to 88.9MHz.
(7channel-200KHz Step)
The Frequency Selector Slide Switch is on one channel of the Modulator and
was set 87.7MHz at thefactory.Assuming it is still there,turn onthe car stereo and
select FM band operation.Tune the radio to 87.7MHz ( depending on frequency
to which the installer has set the unit),or push the pre-set memory button.
INTERFERENCE ON 87.7MHz:
If interference experienced is on 87.7MHz,change the position of the
frequency select switch on the side of the FM Stereo Modulator and
tune the radio 87.7-88.9MHz.
If interference experienced is on 87.7MHz,change the position of the
frequency select switch on the side of the FM Stereo Modulator and
tune the radio 87.7-88.9MHz.
FREQUENCY SELECTOR SWITCH
SPECIFICATIONS:
Frequency: 87.7MHz to 88.9MHz (7channel-200KHz Step)
RF Output Level: 60dB Max
S/N Ratio: 65dB
Stereo Separation: 40dB
FM Modulation Depth: 75KHz at L+R+Pilot
Operating Voltage: 10 ~16V DC
Dimensions: 88W 30H 50Dmm
Weight: 180g
Frequency: 87.7MHz to 88.9MHz (7channel-200KHz Step)
RF Output Level: 60dB Max
S/N Ratio: 65dB
Stereo Separation: 40dB
FM Modulation Depth: 75KHz at L+R+Pilot
Operating Voltage: 10 ~16V DC
Dimensions: 88W 30H 50Dmm
Weight: 180g
Specifications and design are subject to change without noticeSpecifications and design are subject to change without notice
Frequency
Selector Switch
Frequency(MHz)
87.7MHz
87.9MHz
88.1MHz
88.3MHz
88.5MHz
88.7MHz
88.9MHz
Frequency(MHz)
87.7MHz
87.9MHz
88.1MHz
88.3MHz
88.5MHz
88.7MHz
88.9MHz
1234
Loading...