Pyle Pro Vintage PTCDS2UI, PTCDS1U Operating Instructions Manual

CLASSICAL USB TURNTABLE WITH

CD, AM/FM RADIO, CASSETTE

MEDEL:PTCDS2UI

Nostalgic Music System

Operating Instructions Manual

www.pyleaudio.com

1

IMP O RTANT S A FETY I N STRU CTION S

1) Please read these instructions and keep them for future reference.

2) Pay attention to all warnings.

3) Follow all instructions.

4) Do not use this apparatus near water.

5) Clean only with a dry cloth.

6) Do not block any ventilation openings.

7) Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heaters, stoves, or
other apparatus (including amplifiers) that produce heat.

8) Protect the power cord from being walked on or kinked, in particular where
the plug is fitted and at the point where it exits from the apparatus.

9) Only use attachments / accessories specified by the manufacturer.

10) Unplug this apparatus during lightning storms or when unused for long
periods of time.

11) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged,liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

12) This appliance should not be exposed to dripping or splashing water and
no object filled with liquids, such as vases, should be placed on the
apparatus.

13) Do not overload the wall power outlet. Use only power source as indicated

- i.e.120V AC mains.

PREPARATION FOR USE
UNPACKING AND SET UP

● Carefully remove the unit from the display carton and
remove all packing material from the unit.

● Unwind the AC power cord and extend it to its full length.

● Unwind the FM Antenna wire and extend it to its full length.

● Place the unit on a stable, level surface, convenient to an AC
outlet, out of Direct sunlight, and away from sources of excess
h eat, dust, moisture, humidity or strong magnetic fields.

● Raise the lid to expose the phonograph. The phonog raph has
been secured for shipment with a transit screw. Use a coin or
screwdriver to turn the transit screw clockwise. This will allow the
Turntable to “float”.

POWER SOURCE
This product is designed to operate on 120V 60Hz AC only. Attempting to operate this
system from any other power source may cause damage to the system, and such damag e is
not covered by your warranty.

NOTE: You will note that this system is equipped with domestic standard AC power 2-pin

plug. If this plug does not fit into your existing AC outlet, do

not try to defeat this safety feature by filing the wide blade

to make it fit into your outlet. If this plug will not fit into
your outlet, you probably have an outdated
non-polarized AC outlet. You should have your
outlet changed by a qualified licensed electrician.

● Remove the opaque white plastic stylus cover from the phonograph stylus by sliding it
Forward and down.

● Discard the stylus cover.

● Remove the twist-tie that was used to secure the tone arm during shipment.

● Release the tone arm lock lever.

● Connect the plug to your AC outlet.

TRANSIT SCREW

STYLUS COVER

TONE ARM LOCK LEVER

IMPORTANT NOTES

Avoid installing this unit in places ex posed to di rect sunl ight or close to heat radiating
appliances such as electric heaters, on top of other stereo equipment that ra diates to o
much heat, places lacking ventilation or dusty areas, places subject to constant vib ration
and/or humid or moist areas.

Do not attempt to clean this unit with chemical solvents as this might damage the f inish. Us e
a clean dry cloth. Operate controls and switches as described in the manual. Before turn ing
On the power, make certain the AC power cord is plugged in. Store your CDs, In a cool area
to avoid damage from heat. When moving the set, be sure to first disconnect the pow er cord.

2

PROTECT YOUR FURN ITURE

This model is equipped with non-skid rubber 'feet' to prevent the product from moving when
you operate the controls. Th ese 'feet ' are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain typ es of
oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber
'feet' to soften, and leave marks or a rubber residue on the furniture.

AC Outlet

AC Plug