Pyle Pro PYD1808, PYD2808, PYD3808 Owner's Manual
12 – Pyle Pro Mixer Owner’s Manual
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing with the product
• Include in your letter your return address, daytime phone number and R.A. number
• Also include a check or money order for $20.00 for return
shipping, handling and insurance, or provide your Visa/MC number with expiration date.
Our obligation under this warranty is limited to the repair or replacement
of the defective unit when it is returned to us prepaid. This warranty will
be considered void if the unit was tampered with, improperly serviced or
subject to misuse, neglect or accidental damage.
Limited Warranty
PYLE PRO MIXERS
warranty registration card
Thank you for purchasing this PYLE
product. To activate your
warranty, please mail this card
within 10 days.
Name
Address
City, State ZIP
Model No. Serial #
(if available)
Date of Purchase
Purchased at:
Music Products Store
Catalog Merchandiser
Sound Contractor/Installer Mail Order
Other
Please complete warranty card, detach and return
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the mixer.
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully
packed and shipped, prepaid, to:
PYD1808/PYD2808
PYD3808
www.pyleaudio.com
PYD1808/2808/3808
Input Sensitivity/Impedance
Mic 1-2
Phono 1-2
Line 1-8
Output Level
Amp
Booth
R
ecord
Frequency Response
S/N Ratio (at 1 kHz)
Mic
Phono
Line
Distortion
Mic
Phono
Line
Equalizer
Control Frequencies
Boost/Cut R
ange
MIC Tone Control
Treble
Bass
Talkover Attenuation
Echo Delay Time
(PYD 2808)
Sampling Length
(PYD 3808)
Power Source
Dimensions, inches
(mm)
60, 150, 400, 1K, 2.4k,
6k,and 15k
+/- 12 dB from center
10kHz; +12/-12dB
100Hz; +12/-12dB
-16dB
20mS-200mS
12 Seconds
120 VAC, 60Hz/230 VAC, 50 Hz
19.0 x 3.86 x 9.45
(482 x 98 x 240)
pro series
Specifications
1.5 mV/600 Ohms, bal/unbal
3.0 mV/50K Ohms
150.0 mV/27K Ohms
1.5 V/10-kOhms
1.5 V/10-kOhms
150mV/10-kOhms
20Hz – 20kHz +/- 3 dB
>60 dB/1.5mV input
>70 dB/3.0mV input
>80 dB/150.0 mV input
0.20%
0.05%
0.03%
115/230V-60/50 Hz
~AC iN
BOOTHAMP
R
RLL
FUSE
OUTPUT
REC
CH 4 CH 3 CH 2 CH 1
GROUND
MIC 2
INPUT
LINE 1LINE 2
INPUT
PHONO 1
SELECT
LINE 3LINE 4
INPUT
PHONO 2
SELECT
LINE 5LINE 6
LINE 7LINE 8
R
L
CAUTION:
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE
CAUTION:
VOLTAGE
BALANCED
Power Switch
Channel CUE Switch Allows you to monitor the selected audio
input source and prepare it prior to mixing it in.
Equalizer On/Off Selector
BNC Lamp Adaptor Allows
y
ou to connect a 12V/3W
lamp to light the panel
Headphone Jack
Accepts headphones with
1/4” plug
Cue Level Control
Headphone CUE/PGM
Control
Allows you to listen
simultaneously or separately
to the CUE material or the
active program
Booth Level Control
Lets y
ou control the mixer’s
overall booth volume level,
if you set up remote speakers
or DJ booth monitors
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Switch
Channel Assign Switch Lets you select the input source to be mixed
b
y the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between
the input sources assigned to Channel A and Channel B
7-Band Equalizer Allows you to tailor the mixer output to suit your
taste or performance en
vironment. Each frequency range can be
cut or boost by up to 12dB.
Dual Display Meter Indicates the levels of Left and Right Master
Channels
Channel Input Selector Lets you choose the input source to play
for each channel
MIC Talkover Allows you to lower the
lev
el of the input sources so you can talk
them using the DJ Mic
MIC1/2 Level Controls Lets you control
the MIC lev
els as they enter the mix
MIC1/2 Tone Controls
Your PYLE PRO Series Performance Mixer
is a sophisticated control center, perfect for mixing sound from multiple playback sources such as
microphones, tuners, CD players, turntables or the audio outputs from a VCR. This mixer is ruggedly
constructed for home or professional use. Wide range volume controls permit you to adjust sound levels
accurately to achieve just the right mix for playing through your speaker system or for recording.
Please read this manual thoroughly before you attempt to set up and use the mixer. It contains a
range of suggestions and instructions to insure safe usage. Set up and used properly, you can expect
years of trouble-free service from this product.
Input/Output Features: all models
Ground Screw
for turntables
Features and Controls: PYD 1808 Mixer
Pyle Pro Mixer Owner’s Manual – 1i – Pyle Pro Mixer Owner’s Manual
Owner’s Manual Table of Contents
Input/Output Features
Features and Controls: PYD 1808
Features and Controls: PYD 2808
Features and Controls: PYD 3808
Presetting Controls Before Use
Connecting the Mixer Inputs
Connecting the Mixer’s Outputs
to Amplifiers
to Recorders
to Booth Speakers
Using Headphones
Connecting the Lamp
Using the Mixer Controls
Turning On the Mixer
Monitoring (”Cueing”) Inputs
Mixing Inputs
Adding Equalization to the Mix
Using the MicrophoneTalkover Mode
Microphone Tone and Level Controls
Using the Mono/Stereo Switch
Using the Crossfader w/Assign Switches
Using the Echo Controls (PYD 2808)
Using the Sound Effects (PYD 2808)
Using the Digital Sampler (PYD 3808)
Troubleshooting
Specifications Warranty
i
1
2
3
4
6
7
8
8
9
10
11
12
Stereo Line Inputs let you connect
most high-lev
el audio sources, such as
CD players, tape deck, tuner or VCR.
Dual Purpose Stereo Inputs for
using a turntable with a magnetic
cartridge OR a high lev
el input
source
MIC2 Microphone
connector
permits
you to connect a
balanced or
unbalanced low
impedance microphone
with 1/4” plug.
Input Select Switches – set these
switches based on what is plugged
into Phono1/Line1 and Phono2/Line3
input jacks
Output Jacks to connect the mixer to a
receiv
er or amplifier – choose to use cables
with either 1/4” plugs or RCA plugs.
Booth Output Jacks to connect the mixer
to a second receiv
er or amplifier powering
speakers in the DJ booth or in a remote
location
Record Output Jacks to connect the
mix
er to a tape deck for recording the
mixed program
MIC 2 Input Jack (on input panel)
F
or connecting a balanced or
unbalanced low impedance microphone
with 1/4”plug
MIC 1 Combo Input Jack For
connecting a balanced or unbalanced
low impedance microphone with XLR
-
type or 1/4” plug
Pyle Pro Mixer Owner’s Manual – 32 – Pyle Pro Mixer Owner’s Manual
Features and Controls: PYD 3808 Mixer
Equalizer On/Off Selector
BNC Lamp Adaptor Allows
y
ou to connect a 12V/3W
lamp to light the panel
Headphone Jack
Accepts headphones with
1/4” plug
Cue Level Control
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Switch
Channel Assign Switch Lets you select the input source to be mixed
b
y the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between
the input sources assigned to Channel A and Channel B
MIC Talkover Allows you to lower the
lev
el of the input sources so you can talk
them using the DJ Mic
MIC1/2 Level Controls Lets you control
the MIC lev
els as they enter the mix
MIC1/2 Tone Controls
7-Band Equalizer Allows you to tailor the mixer output to suit your
taste or performance en
vironment. Each frequency range can be
cut or boost by up to 12dB.
Dual Display Meter Indicates the levels of Left and Right Master
Channels
Channel CUE Switch Allows you to monitor the selected audio
input source and prepare it prior to mixing it in.
Channel Input Selector Lets you choose the input source to play
for each channel
MIC 2 Input Jack (on input panel)
F
or connecting a balanced or
unbalanced low impedance microphone
with 1/4”plug
MIC 1 Combo Input Jack For
connecting a balanced or unbalanced
low impedance microphone with XLR
-
type or 1/4”plug
Sampler Mode Selector Selects the function of
the sampler section
Sampler Pitch Control Lets you control the
sampled signal’
s pitch
Sampler CUE Switch Allows you to monitor the
desired sample signal
Sampler Level Control Lets you adjust the volume
of the desired sample signal as it enters the mix
Sampler Start/Stop Controls the start and stop
of the sampling process
Booth Level Control Lets
you control the mixer’s
overall Booth volume level,
if you set up remote speakers
or DJ booth monitors
Power Switch
Headphone CUE/PGM
Control
Allows you to listen
simultaneously or separately
to the CUE material or the
active program
Features and Controls: PYD 2808 Mixer
Equalizer On/Off Selector
BNC Lamp Adaptor Allows
y
ou to connect a 12V/3W
lamp to light the panel
Headphone Jack
Accepts headphones with
1/4” plug
Cue Level Control
-Let you adjust the
headphone's volume level
Headphone CUE/PGM
Control
Allows you to listen
simultaneously or separately
to the CUE material or the
active program
Master Level Control Lets you control mixer’s overall volume level
Master Mono/Stereo Switch
Channel Assign Switch Lets you select the input source to be mixed
b
y the Crossfade Slider Control
Crossfade Slider Control Allows you to smoothly switch between
the input sources assigned to Channel A and Channel B
MIC Talkover Allows you to lower the
lev
el of the input sources so you can talk
them using the DJ Mic
MIC1/2 Level Controls Lets you control
the MIC lev
els as they enter the mix
MIC1/2 Tone Controls
7-Band Equalizer Allows you to tailor the mixer output to suit your
taste or performance en
vironment. Each frequency range can be
cut or boost by up to 12dB.
Dual Display Meter Indicates the levels of Left and Right Master
Channels
Channel CUE Switch Allows you to monitor the selected audio
input source and prepare it prior to mixing it in.
Channel Input Selector Lets you choose the input source to play
for each channel
MIC 2 Input Jack (on input panel)
F
or connecting a balanced or
unbalanced low impedance microphone
with 1/4” plug
MIC 1 Combo Input Jack For
connecting a balanced or unbalanced
low impedance microphone with XLR
-
type or 1/4” plug
Sound Effect Volume Control Lets you control
the volume level of the sound effect within the mix
Sound Effect Speed Control Lets you control
the pitch of the selected sound effect
Digital Sound Effects Selectors Lets you create
special sound performance mixes from the six
preprogrammed special effects
Power Switch
Booth Level Control Lets
y
ou control the mixer’s overall
Booth volume level, if you set
up remote speakers or DJ booth
monitors
ECHO Level Control Controls the depth of the
echo effect
ECHO Repeat Control Lets you control the time
period during which the echo is repeated
ECHO Delay Control Lets you adjust the delay
time for the echo
ECHO On/Off Switch
Loading...