How it Works
Pyle Pro
Loading...
PRJSD188
User Manual
15 pgs831.62 Kb0

Pyle Pro PRJSD188 User Manual

ALL-IN-ONE LCD PROJECTOR
MODEL NO.:PRJSD188
USER'S MANUAL
~
VIDEO
Read the manual carefully,before use the projector
TV
AMPLIFIER
WARNING
warning
Please remember the model Number and series number if you need. And please check all accessories when you drop the carton package
When you use this projector , please read this manual carefully
MODEL NUMBER SERIES NUMBER
LCD
Input signal
Model
video
audio
Specification
Component video ,s-video, VGA , HDMI ,Ypbpr ,TV(optional), USB
Stereo
Warning
Do not see the light from the lens ,it is high bright lamp. It will damage your eye .specially for children
Warning :Do not place the projector in the wet condition, avoid to getting an electric shock
High Voltage ,do not open it , except for professional
WARNING
Warning when close the projector ,the fans will continue to turn 90seconds. Before pull out the power cable, please be sure the fans stop to turn . Or it will damage the projector lamp.
It indicates there is a instruction for important operation
It indicates there is a dangerous voltage
Output signal
LCD
Lens
Lamp
Image
Working condition
Store condition
audio
Native resolution contrast ratio
Aperture Focus
Power Colour -temp life working time
Size Brightness keystone
Voltage power consumption
Temperature humidity
Tempe ration humidity
Stereo output ,coaxial output 5w*2 speaker and earphone
800*600(support 720P,1080P) 800:1
2.9 170mm
150w 9300k 8000hours <10 hours
90v-110v/ 60HZ
200
W
About the remote control battery:
The remote control battery should be fixed correctly , Or it will damage the remote control. Make sure the remote control out of children reach
1
¼ÌÖμÌÖÎ
Remote control
Machine
11
Frequency
Size weight
(If all parameter changed, do not note again)
26
Trouble shooting
Safety precautions
problem
No image
Projector turns off automatically
Lamp doesn t work
Possible situation
If choose the right signal mode
If open the input signal devices
If connect the signal cable
If connect the signal cable well
Under VGA mode ,setting the computer frequency must over 75KHz?
Dust cover the filter
The filter long time no clean, please clean it by water
The voltage is too low or big fluctuation
When you turn off the projector , the lamp too hot, please wait at least 5 minute ,then you can turn it on again.
Input power are wrong ,please confirm your projector power specification 220V or 110V
Lamp are broken or out of service life please replace the lamp and test it again
Warning; when use this projector ,please read this manual carefully. If wrong operation ,it will cause electric shock or fire.so when use and repair this projector ,please comply with the following points
1,Read manual Before use this projector ,please read full manual carefully and operate according to this manual instruction
2,Clear when clear this projector ,please pull out the power cable. Use the wet cloth to clear,not the cleasner
3.Accessory please use our recommended accessory. Or it will damage the projector. 4,Use environment Donot place the projector in wet environment 5,installation and fix please place this projector in stable table . 6, Ventilation the ventilation in the projector are best for projector work stably. Donot let the dust wall up the filter. Or it will cause the projector high-temperature protected. So please use the water to clear the filter per month. 7, Power please make sure the power same as your projector inquiry specification. (220 V or 110V) 8, Earthing wire this projector has earthing wire . It is three pin plug.
9,protect the power cable Please confirm the power cable are perfect when connect the projector. 10,Thunder when the thunder happen or long time no use , please pull the power cable out of projector. 11,Repairment As the high voltage inside ,please donot open or try to repair the projector by yourself. . Please ask a professional technician to repair the projector. 12, Far away Heat device please make sure this projector far away other heat device . It will damage the projector service life
25
2
Caution
Trouble shooting
About the installation In order to improve the projector service life, It shouldnot place in a wet and ventilation condition
Donot put the projector under the sunshine directly
Projector working temperature: 0 +70
Projector store temperature : -20 +70
Donot block the ventilation-window of projector If the projector interior temperature are too hot , the machine will be shut off automatically.This is hot ­protected system. So please clean the filter of projector per month . It is very important. Donot let the dust cover the filter.
About Open and close the projector
when open the projector ,connect the power cable and press the "power" key on the panel .the projector will work ,but the lamp will be bright more and more .After 5 minutes, the lamp work normally
when close the projector , press the power key again . And then the lamp shut off. But the fans still work until 5minutes later. When close the projector ,donot pull out the power cable directly . After 5minutes, the projector will shut off automatically.
Warning
Fans will adjust the temperature It is controlled by system when the projector work, the fans turn slowly or quickly so the fans noise are different But it is normal when the projector work ,donot pull out the pwer cable If the fans stop to work,it will cause the projector interior temperature very high, so it may damage the projector.
The projector operation is very simple . Just like to use TV. please refer to this chapter when you encounter a problem
Problem
No power
Remote control cannot open or close the projector
If there is no batteries in the remote control
If have obstruction between remote control and projector
If have strong ray on the projector
This machine just turn off . You should wait 5minutes and open the machine again.
Possible situation
If open the power key
3
24
Loading...
+ 10 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use