Pyle Pro PLTTB8UI Operating Instructions Manual
BALANCE
CAUTION
TO
PREVENT
FIRE
OR
SHOCK
HAZARD,
DO
NOT
USE
THIS
PLUG
WITH
AN
EXTENSION
CORD,
RECEPTACLE
OR
OTHER
OUTLET
UNLESS
THE
BLADES
CAN
BE FULLY
INSERTED
TO
PREVENT
BLADE
EXPOSURE.
TO
PREVENT
FIRE
ORSHOCKHAZARD,DONOTEXPOSETHISAPPLIANCETORAINORMOISTURE.
CAUTION
RISK
OF
ELECTRIC
SHOCK
DO
NOT
OPEN
The
lightning
flash
with
arrow·
WARNING
:TOREDUCETHE
head
symbol,
within
an
equi·
RISK
OF
ELECTRIC
SHOCK
lateral
triangle
is
intended
to
DO
NOT
REMOVE
COVER
alert
the
user
to
the
presence
(OR BACK)
NO
USER
ofuninsulalad'dangerousvoHage
SERVICEABLE
PARTS
within
the
product's
enclosure
INSIDE
REFER
SERVICING
that
may
be
of
sufficient
TO
QUALIFIED SERVICE
magmtu~e
to
constitute a risk
PERSONNEL
of
electnc
shock
to
persons.
.
The
exclamation
point
within
an
equilateral triangle
is
in-
tended to alert the user to
the
presence
of
important
operating
and
maintenance
(servicing) instructions
in
the
literature accompany-
ing
the
appliance.
IMPORTANT
SAFETY
INSTRUCTIONS
1.) Read
these
instructions.
2.)
Keep
these
instructions.
3.)
Heed all
warnings.
4.)
Follow
all
instructions.
5.)
Do
not
use
this
apparatus
near
water.
6.)
Clean
only
with
dry
cloth.
7.)
Do
not block any ventilation openings. Install
in
accordance with the manufacturer's
instructions.
8.)
Do
not install near any heat sources such
as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9.)
Do
not defeat the safety purpose
of
the polarized or grounding type plug. A polarized
plug has two blades with one wider than the other. Agrounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not fit into you outlet, consult
an
electrician for
replacement
of
the obsolete outlet.
10.) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and point where they exit from the apparatus.
11.) Only use attachments
I accessories specified by the manufacturer.
12.) Unplug this apparatus during lightning storms or when unused for long periods oftime.
13.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has
been damaged in any
way,
such
as
power-supply cord or plug is damaged, liquid
has
been
spilled or objects have fallen into the apparatus, the apparatus has been exposed
to
rain or moisture, does not operate normally, or has been dropped.
14.) This appliance shall not
be
exposed to dripping or splashing water
and
no
objectfilled
with liquids such
as
vases shall
be
placed
on
the apparatus.
15.) Do
not
overload
wall
outlet.
Use
only
power
source
as indicated.
16.) Use
replacement
parts
as
specified
by
the
manufacturer.
1
L
PREPARATION FOR USE
UNPACKING
AND
SET
UP
• Carefully remove the unit from the display carton and remove all packing
material from the unit.
• Unwind the DC power plug and extend
it
to its full length.
• Unwind the speakers and extend
it
to its fuillength(open the speakers
fastener(L/R).
• Place the unit on a stable, level surface, convenient to an AC outlet, out
of
direct sunlight, and away from sources
of
excess heat, dust, moisture,
humidity,
or
strong magnetic fields.
• Connect the plug to
your
AC outlet.
• Raise the lid to expose the phonograph. The phonograph has been secured
for shipment with a transit screw. Use a coin
or
screwdriver to tum the transit
screw clockwise. This will allow the turntable to
..
float".
TRANSIT SCREW
2
L
•
Remove the opaque white plastic stylus
cover from the phonograph stylus by
sliding it
in
the direction
of
the arrow.
Discard the stylus cover.
TONE
ARM
LOCK
LEVER
•
Remove the twist-tie that was used to
secure the tone arm during shipment.
Release the tone arm lock lever.
STYLUS
COVER
•
Connect the plug to your AC outlet.
POWER SOURCE
This system is used dc adaptor operate
on
normal 120V 60Hz DC only.
Attempting to operate from any other power source may cause damage to the
system, and such damage is not covered by your warranty.
NOTE: If this plug will not fit into your outlet, you probably have an out-dated
non-polarized AC outlet.
You
should have you outlet changed by a qualified
licensed electrician. The DC adaptor output DC
12V,
push
in
DC jack.
Please pull the power plug during shock and unused for a long time.
The
power
plug and
power
jack
should
be
matched
as a suitable
make
and
break
device,
in
order
to make
operation
conveniently.
IMPORTANT: Raising And Lowering The Lid
To
open the lid, raise it as far as it will go until the lid support bracket 'locks'
in
the open position.
To
close the lid, lift it upward slightly until the lid support
bracket 'unlocks'
,and
then gently lower the lid.
TO AVOID DAMAGING THE CABINET
OR
THE LID, NEVER FORCE THE LID CLOSED.
ALWAYS RAISE THE LID TO RELEASE THE LID SUPPORT BRACKET.
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These'feet'are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains
on
your furniture. However certain types
of
oil based furniture polishes, wood
preservatives, or cleaning sprays may cause the rubber 'feet' to soften, and
leave marks or a rubber residue on the furniture.
To
prevent any damage to your
furniture we strongly recommend that you purchase small self-adhesive felt
pads, available at hardware stores and home improvement centers everywhere.
3
L
LOCATION OF CONTROLS AND INDICATORS
FRONT PANEL
1) Phonograph Lid.
9)
2) Phonograph Lid
Support
Bracket. 1 0)
3)
Speakers
11)
4) Turntable.
12)
5) IPOD
slot
13)
6)
Handle
14)
7) Phones
jack
15)
8)
Turntable's Fastener
BACK PANEL
16 17
m
I I
b~
m
Gp
I
~
..
~~
I
19 18
4
Turntable's Fastener plug
BALANCE control
BASS control
VOLUME control
FUNCTION control
POWER
Button
PC port
16) DC
IN
Jack
17) AUX
IN
Jack
18) DC SUPPLY COMPARTMENT
19) DC SUPPLY COMPARTMENT
FASTENER
L
Loading...