Monitor Plate Attachment
Monitor Plate Attachment
If the monitor is VESA compliant, bolt the Monitor Plate directly to the monitor,
as described in Step 3.
If the monitor is not VESA compliant, bolt the Monitor Plate to the Adaptor
Plate (sold separately) using the following mounting pattern (fig. 6):
Caution:
Caution:
use an electric drill to secure screws.
Complete the installation as per Steps 4 5.&
Caution :This Product LCD /Plasma Wall Mount Bracket is
Caution :
intended for use only with the maximum weights indicated .See apparatus
instructions .Use with products heavier than the maximum weights
indicated may result in instability causing possible injury .
Never force screws into the monitor, as damage may occur. NEVER
Fig. 6
A
A
Flat Panel Fixed Mount
INSTALLATION GUIDEINSTALLATION GUIDE
Item No.:PWLB008Item No.:PWLB008
-8-
TV size range 10 37:"-"
Universal VESA mount
Low profile: only from wall19mm
Easy to install: sliding plate operation
Max load capacity:25Kg/55lbs
IMPORTANT: If don’t understand about right install ways, please
IMPORTANT
consult to normal installing specialist.
Parts:
Optional Installations
Optional Installations
Letter
1
2
3
Qty
1
2
3
A
B
C
D
E
F
G
H
I
J
K
L
1
1
2
4
4
4
4
4
4
4
4
4
3
3
3
Description
Monitor Plate
Wall Plate
Safety bolt
M4X12 bolt
M4X25 bolt
M5X12 bolt
M5X25 bolt
M6X12 bolt
M6X25 bolt
M5 washer
M6 washer
9/16 spacer"
Long bolt
Long bolt washer
Wall an chor
In addition to being used as a flat panel wall mount, the mount can
also be used in conjunction with other products.
When used between a Cantilever and a flat panel display, this mount
creates a quick disconnect mount.
Wall Plate Attachment
Wall Plate Attachment
Install the Wall Plate onto the other product using one of the following
mounting patterns (fig. 5):
1. PSW123S (VESA 100)
2. PSW123L
3.
PSW123S (VESA 200)
Proceed to Monitor Plate Attachment on next page.
2
1
3
3
-2-
A
B
D
C
E F
G
H
I J
L
K
1
2
Fig 5
-7-
Step 1
Step 1
Determine the desired location for the monitor.
Determine the desired location for the monitor.
I
Note:
When mounting to wooden studs, the Wall Plate can be offset up to 2”
Note:
in either direction from stud center (+/-2”) by utilizing the offset mounting
GH,
holes. ( Fig. 1)
Step 4
Fig 4
Step 4
Carefully position monitor so that Wall Plate and Monitor Plate are vertically aligned,
with the bottom of Monitor plate overlapping the top of the Wall Plate.
Gently lower monitor into position, sliding the two plates together until the Monitor
Plate bottoms out against the Wall Plate. (Fig. 5)
Caution:
Caution:
sides of the mount before releasing grip on monitor.
Make sure that the plates are engaged on both
1
AF-
1
2
Step 5
Step 5
Important:
Important:
Make sure there is adequate mounting space available for the
monitor, considering the monitor dimensions.
The mount is supplied with the necessary hardware for either Wooden Stud
Mounting or Masonry Mounting. Determine your mounting type and proceed
accordingly, as shown on next page.
4"(102mm）
+2"
-2"
Thread two Safety Screws (3) through bottom of
Wall Plate and into Monitor Plate, to secure the
assembly. (Fig. 5)
-6-
Fig 5
3
Fig. 1
-3-
Step 2
Step 2
Wooden Stud Mounting
Wooden Stud Mounting
Using an electronic stud finder, locate the center of the wooden stud.
Position the Wall Plate (2) in desired mounting location over stud.
Level the Wall Plate, and then using the Wall Plate as a template, mark
mounting hole locations over the center of the stud.
Using a 5mm drill bit, drill 3 mounting holes into the stud to a depth of 80mm.
Securely mount Wall Plate with supplied Long Bolts (J) and Washers (K). (Fig. 2)
Important:
Important:
bolt into the stud. This makes the installation easier, and will prevent damage
from occurring to the bolt.
Fig. 2
Dab a bit of liquid soap onto the bolt threads before the driving
L
K
J
Step 3
Step 3
This mount Monitor Plate is VESA compliant, and supports the following
VESA Patterns ( Fig. 3):
A: VESA 75 (75mm x 75mm)
B: VESA 100 (100mm x 100mm)
C: VESA 200 (100mm x 200mm)
D: VESA 200 (200mm x 200mm)
Non VESA compliant displays will require an optional adaptor plate.
Contact your dealer for details.
For details on attaching the Monitor Plate to a Adaptor Plate, turn to page 8.
Fig. 3
D
Masonry Mounting
Masonry Mounting
Position the Wall Plate (2) in desired mounting location on wall.
Level the Wall Plate , and then using the Wall Plate as a template, mark
mounting hole locations on wall.
Using a 10mm masonry bit, drill 3 mounting holes into masonry to a depth
of 80mm.
Insert Wall Anchors (L) into the mounting holes, and lightly tap them flush
to the wall with a hammer, as shown in Fig 2.
Caution:
Caution:
NEVER
NEVER
Securely mount Wall Plate with supplied Long Bolts (J) and Washers (K). (Fig. 2)
Wall Anchors should only be used for masonry mounting.
use wall anchors to mount this mount to drywall.
-4-
C
B
A
B
C
D
Attach Monitor Plate to back of the monitor with 4mm, 5mm, or 6mm
mounting Screws. (A-F) (Fig. 4) Check the monitor’s owners manual for
correct size screws to use.
Note:
Some monitors with recessed mounting lands, will require the use of
Note:
Spacers (I), as shown in Fig. 4.
Caution:
Caution:
use an electric drill to secure screws.
Never force screws into the monitor, as damage may occur. NEVER
-5-
Loading...