Part 5-Adjusting display and using cord management
Part 5-Adjusting display and using cord management
Route cords along articulating arms using cord management s.
clip
Articulating arms can be adjusted to position display into desired location.
Use wrench(8) to tighten and loosen the tension screw. Do not overtighten
or overloosen to make the screws come out.
±180°
±180°
±180°
-5 15°~ °
Wrench
4x4
Wrench
5x5
±5°
Thank you for choosing our productThank you for choosing our product
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
Warning
This product contains small items that could be a choking hazard if swallowed. Keep
these items away from young children
1.Make sure these instructions are read and completely understood before attempting
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
2.The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; otherwise the structure must be reinforced
3.Safety gear and proper tools must be used. A minimum of two people are required
for this installation. Failure to use safety gear can result in property damage, serious
injury or death.
!
.
INSTALLATION GUIDE
Item No.:
Item No.:
TV Size Range: 37 55
Maximum Weight Capacity: 35kg/77lbs
VESA: 700X500
Safety automatic lock
Unlock cord
This product was designed to be installed on wood stud walls and solid concrete walls.
Before installing make sure the supporting surface will support the combined load of the
equipment and hardware. Never exceed the Maximum Load Capacity. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or
personal injury.The depth of this mount(1.3 ) may not provide sufficient space for proper
ventilation on some screens. Please refer to the manufacturer’s requirements for mounting
your screen befourinstallation.
PSWLE82
PSWLE82
"～ "
CAUTION
"
www pyleaudio com..
-8-
Hardware Kit:
Hardware Kit:
Part 4-Mounting the flat panel screen
Part 4-Mounting the flat panel screen
8
Magnetic removable
bubble level
A-D
ID Description
Qty
Wall plate
1
2
3
4
5
6
7
8
1
Bracket
2
Ribbon
2
TV plate
1
Plastic cover
2
2
Screw
2
Slide block(Position lock)
2
Wrench(4x4,5x5)
5
Hook the top of brackets onto the center of wall plate(1). Then swing the
(2)
screen down. Fixed slide block(7) into wall plate by screw(6).
1
7
6
NOTE:
NOTE:
Always use an assistant or mechanical lifting equipment to safely lift
and position heavy equipment.
2
4
7
2
3
E
F
G
H
6
Use the box wrench to loose the
ID
Qty
4
A
4
B
4
C
4
D
4
E
4
F
4
G
4
H
Description
M4 mm×16 bolt
M5 mm×16 bolt
M6× mm16 bolt
M8×16mm bolt
Square washer
Long bolt washer
Long bolt
Wall anchor
screw if there's too tight to tilt
FIG.A
Before installation, please attach these two decorative end caps to the two
sides of TV plate.(FIG.A)
-2-
-7-
Part 3-Attaching brackets to screen
Part 3-Attaching brackets to screen
Part 1a-Wood Stud Mounting
Part 1a-Wood Stud Mounting
Center brackets vertically on back of screen. Select the
(B or C) or large(D) screws.
Attach brackets to screen using four selected
small(A),medium
screws and four square washers(E) at the top and bottom of each bracket.
Tighten screws firmly. Do not overtighten
.
Square washer(E)
E
Large hole for
M8 screws
Medium hole for
M5andM6screws
Small hole for
M4 screws
A-D
Usewallplate(1)asatemplate,makesureitislevel,andmarkfourmounting
holes along the center lines of the wood studs. Drill four 3/16
””(5mm)dia
.
holes 2 (50mm) deep. Level wall plate(1) and attach to wall with four long
bolts(G and four washers(F . Tighten screws firmly Do not overtighten
)) ..
2 50mm)”(
Φ3/16 (5mm)”
Stud finder
Wood stud
Magnetic removable
F
bubble level
G
-6-
-3-
Part 1b-Concrete Wall Mounting
Part 1b-Concrete Wall Mounting
Part 2-Attaching plastic covers to wall plate
Part 2-Attaching plastic covers to wall plate
Level wall plate(1) and use wall as a template to mark four holes. Drill four
3/8 (10mm) dia. holes 2 (50mm) deep. Insert four anchors(H) into holes
””
and secure wall plate with four long bolts(G) and four washers(F).Tighten
screws firmly. Do not overtighten
.
2 (50mm)”
Φ3/8 (10mm)”
Concrete Wall
H
F
Magnetic removable
bubble level
G
Secure plastic covers over wall plate by pushing them toward each other
until they lock in place.
5
If you think the ribbon is too long, You can hide it at the back of the
televesion,once you want to uninstall the TV, it can help you to take out the
brackets
.
3
-4-
-5-
Loading...