Part 5-Adjusting display and using cord management
Part 5-Adjusting display and using cord management
Route cords along articulating arms using cord management s(7).
clip
Articulating arms can be adjusted to position display into desired location.
Use wrench to tighten and loosen the tension screw. Do not overtighten
and do not loosen to the point the screws come out.
8
9
7
Thank you for choosing our productThank you for choosing our product
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
This product contains small items that could be a choking hazard if swallowed. Keep
these items away from young children
1.Make sure these instructions are read and completely understood before attempting
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
2.The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; otherwise the structure must be reinforced
3.Safety gear and proper tools must be used. A minimum of two people are required
for this installation. Failure to use safety gear can result in property damage, serious
injury or death.
Warning
!
.
INSTALLATION GUIDE
Item No.:PSW771Item No.:PSW771
TV size range: 32 50
Maximum weight capacity: 40 kg /88lbs
Adjustable angle: 0 12
This product was designed to be installed on wood stud walls and solid concrete walls.
Before installing make sure the supporting surface will support the combined load of the
equipment and hardware. Never exceed the Maximum Load Capacity. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or
personal injury.
～～""
°°
www pyleaudio com..
MADE IN CHINA
CAUTION
-8-
Hardware Kit:
Hardware Kit:
Part 3- Hanging display
8
9
2
1
Part 3- Hanging display
Firstly lift the bracket mounted display over the mount. And then hook
the brackets over the top of the mount. Rotate the display let the
bottom of the brackets hook over the bottom of mount. Then put safety
bolts into the bottom of the brackets and lock it.
Warning: Some TV require two people to lift, as we are not responsible
Warning:
for any personal injury or product damage due to mishandling.
7
5
3
6
A-H
ID Description
Qty
1
2
3
4
5
6
7
8
9
A
B
Wall plate
1
Cantilever Arm
1
1
Left Bracket
1
Right Bracket
TV plate
1
Safety bolt
2
Cord management wrap
3
6x6 Wrench
1
1
5x5 Wrench
4
M4 mm×12 bolt
4
M4 mm×16 bolt
4
JM
ID
C
D
G
M
K
Qty
4
4
E
4
F
4
4
H
4
I
4
J
4
4
K
L
4
4
LI
Description
M5× mm16 bolt
M6× mm16 bolt
M8×16mm bolt
M ×36mm5 bolt
M6×36mm bolt
M ×36mm8 bolt
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
2,3
1
-2-
-7-
Part 2b-Attaching brackets to screen with recessed back
Part 2b-Attaching brackets to screen with recessed back
Part 1a-Wood Stud Mounting
Part 1a-Wood Stud Mounting
Center brackets vertically on back of screen. Select the medium(F or G) or
large(H) screws. Attach brackets to screen using four selected screws,four
square washers(I) and four spacers(M) at the top and bottom of each bracket.
Tighten screws firmly. Do not overtighten.
Square washer(I)
Large hole for
M8 screws
Medium hole for
M5andM6screws
M
I
F-H
2 50mm)”(
four
(5mm)dia
”
”
3/16 (5mm)
.
Usewallplate(1)asatemplate,makesureitislevel,andmark mounting
holes along the center lines of the wood studs. Drill four 3/16
holes 2 (50mm) deep. Level wall plate(1) and attach to wall with four long
bolts(J and four washers(L . Tighten screws firmly Do not overtighten
”
)) ..
Stud finder
Wood stud
L
J
-6-
-3-
Part 1b-Concrete Wall Mounting
Part 1b-Concrete Wal l Mounting
Part 2a-Attaching Brackets To Screen With Flat Back
Part 2a-Attaching Brackets To Screen With Flat Back
Level wall plate and use wall as a template to mark four holes. Drill four
3/8 (10mm) dia. holes 2 (50mm) deep. Insert four anchors(K) into holes
””
and secure wall plate with four long bolts(J) and four washers(L). Tighten
bolts firmly. Do not overtighten
.
2(” 50mm)
Φ3/8 (10mm)”
Concrete Wall
K
Center brackets vertically on back of screen. Select the small(A or B),
medium(C or D) or large(E) screws. Attach brackets to screen using four
selected screws and four square washers(I) at the top and bottom of each
bracket. Tighten screws firmly. Do not overtighten
.
Square washer(I)
Large hole for
M8 screws
Medium hole for
M5andM6screws
Small hole for
M4 screws
I
A-E
-4-
L
J
-5-
Loading...