Step 4: Hanging display
Step 4: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.4a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.4b.
Warning: Some TV require two people to lift, as we are not responsibleforany
Warning:
personal injury or product damage due to mishandling.
2,3
1
Fig 4a
5
the facing of a quilt
Fig 4b
Thank you for choosing our productsThank you for choosing our products
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
Tilt Flat Panel TV Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
Item No.:PSW503STItem No.:PSW503ST
Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Weight Capacity:10kg/22lbs~50kg/110lbs
TV size range: 26 ~42
Adjustable angle: 5 15
Inside has balance adjust system
Bulit in leveler system
""
-～
www pyleaudio com..
MADE IN CHINA
-8-
IMPORTANT: If don’t understand about right install ways, please
IMPORTANT:
consult to normal installing specialist.
Hardware List: Actual parts appearance and the quantity may different
Hardware List:
with illustrated.
2
3
1
6
4
5
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall
Woodenwall:
Woodenwall:
Using a awl or nail to make where the nails are located, as shown as Fig.3b.Distance
between two nails for fixing wall mount must not less than 16 . Slide the plate into
position as required.(Fig.3c) Pre-drill these holes with a 5mm drill bit to at least
40mm in deep hole. Use wall mount as a template to mark the location of other three
holes and drill the same holes.
Fixthewallmounttothewallwith4longbolts(H)andwashers(J) .
Brick, Concrete and Stone wall:
Brick, Concrete and Stone wall:
Using a awl or nail to make where the nails are located. Distance between two nails
for fixing wall mount must not less than 16 . Slide the plate into position as required.
(Fig.3c) Pre-drilltheseholeswitha10mmdrillbittoatleast50mmindeephole.Use
wall mount as a template to mark the location of other three holes and drill the same
holes. Please make sure these holes are level and eudipleural. Insert wall anchors(I)
into each of these holes. Attach the wall mount to the wall using 4 long bolts(H) and
washers(J)by box wrench(6).
Please make sure these holes are level and eudipleural.
-wooden, brick, concrete and stone.
”
by box wrench(6)
”
-2-
A-F
ID Description
Qty
Wall mount
1
1
1
2
3
4
5
6
A
B
C
Left bracket
1
Right bracket
Cable Cover
1
Safe bolt
2
Box wrench
1
4
M4 mm×12 bolt
4
M4 mm×16 bolt
4
M5× mm16 bolt
G
ID
I
Qty
4
D
4
E
4
F
4
G
4
H
4
I
4
J
K
4
H
J
Description
M6×16mm bolt
M5×36mm bolt
M6×36mm bolt
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
K
Plate
Fig 3b Fig 3c
Balance-adjusting
1
J
H
6
Using balance-adjusting system on the plate,
make sure whether wall plate is installed
balance. If not, then slide the wall plate let
pointer level in the center position.
Fig 3d
-7-
Step 2: Install the Cable Cover
Step 2: Install the Cable Cover
Route the cables as required. Snap the cable cover into place onto
the rods (Fig. 2a), and then slide the cover into position as required.
(Fig. 2b)
Fig 2a Fig 2a
Step 3: mount to wall
AttachStep 3: Attach mount to wall
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 3a).
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15 (Fig 3a).
For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
15 degree
viewing angle
°
b
WARNING
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
Note:
The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
Caution:This Product LCD /Plasma Wall Mount Bracket is intended for use only
Caution:
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Step 1: Attach bracket to TV
Step 1: Attachbracket to TV
CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-5 of theseinstructions for examples.
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts, spacers andwashers for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly securethe
bolts.
IMPORTANT:
IMPORTANT
equipments and injure of person. Don't use electric drill to fasten any bolts.
Don't force the bolt into the hole, which will cause a damage of
-6-
eyelevel
a
Fig 3a
-3-
Following examples shows how to use bolts, spacers and square washers.
1.Somedisplays have vertical backs. No spacer isrequired. Install the bracket directly
to the back of displayby using bolts and square washers provided. As shown in Fig.1a.
2. Some displays havecurved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(K) betweendisplay and
thebracket.AsshowninFig1b.
Fig a
3
M6 Fig bit
M5 Fig bitM4 Fig bit
K
M6 Fig bitM5 Fig bit
K
A,B
2
G
G
C
3
G
E
Fig 1b
3
G
F
-4-
3
Fig 1a
G
D
-5-
Loading...