PYLE Audio PSW501SF User Manual
Step 4: Hanging display
Step 4: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.4a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.4b.
Warning: Some TV require two people to lift, as we are not responsibleforany
Warning:
personal injury or product damage due to mishandling.
Fixed Flat Panel TV Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
2
1
Fig 4a Fig 4b
Thank you for choosing our productsThank you for choosing our products
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
4
the facing of a quilt
Item No.:PSW501SFItem No.:PSW501SF
Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Max load capacity:50kgs/110lbs
TV size range: 26 ~42""
Inside has balance adjust system
www pyleaudio com..
Bulit in leveler system
MADE IN CHINA
-8-
IMPORTANT: If don’t understand about right install ways, please
IMPORTANT:
consult to normal installing specialist.
Hardware List: Actual parts appearance and the quantity may different
Hardware List:
with illustrated.
2
2
1
5
3
4
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall
Woodenwall:
Woodenwall:
Using a awl or nail to make where the nails are located, as shown as Fig.3b.Distance
between two nails for fixing wall mount must not less than 16 . Slide the plate into
position as required.(Fig.3c) Pre-drill these holes with a 5mm drill bit to at least
40mm in deep hole. Use wall mount as a template to mark the location of other three
holes and drill the same holes.
Fixthewallmounttothewallwith4longbolts(H)andwashers(J) .
Brick, Concrete and Stone wall:
Brick, Concrete and Stone wall:
Using a awl or nail to make where the nails are located. Distance between two nails
for fixing wall mount must not less than 16 . Slide the plate into position as required.
(Fig.3c) Pre-drilltheseholeswitha10mmdrillbittoatleast50mmindeephole.Use
wall mount as a template to mark the location of other three holes and drill the same
holes. Please make sure these holes are level and eudipleural. Insert wall anchors(I)
into each of these holes. Attach the wall mount to the wall using 4 long bolts(H) and
washers(J) by Box wrench(5).
Please make sure these holes are level and eudipleural.
-wooden, brick, concrete and stone.
”
by Box wrench(5)
”
-2-
A-F
ID Description
Qty
Wall mount
1
1
2
2
3
4
5
A
B
C
Bracket
Cable Cover
1
Safe bolt
2
Box wrench
1
4
M4 mm×12 bolt
4
M4 mm×16 bolt
4
M5× mm16 bolt
G
ID
I
Qty
4
D
4
E
4
F
4
G
4
H
4
I
4
J
K
4
H
J
Description
M6×16mm bolt
M5×36mm bolt
M6×36mm bolt
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
K
Plate
Fig 3b Fig 3c
Balance-adjusting
1
J
H
5
Using balance-adjusting system on the plate,
make sure whether wall plate is installed
balance. If not, then slide the wall plate let
pointer level in the center position.
Fig 3d
-7-
Loading...