Pyle Audio PS-CHD30 User Manual

Pyle - Model: PSCHD30

USER MANUAL

End User Notice:
High definition and high frame rate video capture
devices,place huge demands on memory cards.
Pending your user settings,it is recommended that a
4GB(or higher) CLASS 10 SD Card be used to avoid
Read/Write complic ations, which w i ll appear as an error
message on the screen during use. If you are not
sure,please test any lower class cards (Read/Write
speed) in the device before use.

1

Mounting Accessories

2

WATERPROOF CASE

3. Power Button

1.Clamp

2. Shutter Release

1. Insert a finger at the half circle of the Clamp by prying the clamp up away from the case.

2. Before sealing the case, inspect the water sealing gasket to be sure it’s in good condition. You can test the

gasket by closing the case without inserting the camera.

Submerse the case completely in a bowl of water for about a minute. Remove the case from the water, dry
off its exterior with a towel, then open the case. If the entire interior is dry, the case and gasket are safe for use
under water.

3. There are just two buttons required for recording video and images: the Shutter Release, and the Power

Button.

4. Remember to put the Mode Switch in your desired recording position before inserting the camera in the

waterproof case. There is no external button for the Mode Switch.

3

4

1

HANDLEBAR SEATPOST MOUNT

2. Locking Wheel

4. Bar Clamp

1.

-20 Screw

3. Bar Clamp Bolt

1. The camera dose not have a standard tripod mount. For all the accessories with a 1/4-20 screw, the camera
must be enclosed in with the waterproof case or in the included mounting adapter.

2. Turn the waterproof case (or mounting adapter) clockwise onto the 1/4-20 screw of the handlebar clamp
until secure.

3. Turn the Locking Wheel so it applies pressure to the case to keep the connection secure.

4. Loosen the Bar Clamp Bolt until the screw can be pushed 90°upward.

5. The bottom half of the Bar Clamp can be opened to allow you to wrap the Handlebar Clamp around the actual
handlebar of your bicycle.

6. After positioning the Handlebar Clamp where you want it, close up the bottom half of the clamp and tighten
the Bar Clamp Bolt.

5. Tilt Knob

4

4

1

7. Loosen the Tilt Knob, to adjust for the proper aiming angle; then tighten the knob.

1.Helmet Belt

2.Helmet Mount

8. Panning adjustments can be made by loosening the Locking Wheel, adjust the pan angle; then tighten the

wheel.

HELMET MOUNTING SYSTEM

3.

-20 Screw

1. Insert the free end of the Helmet Belt through one of the slots in the base of the Helmet Mount.

2. Thread the same end in to the helmet vent and then back up to the Helmet Mount through another vent. Then
insert the belt through the other side of the Helmet mount. Then insert the belt back through the helmet vent.

3. You should have now both ends of the belt inside the helmet. take both ends of the Belt and pull to tighten and
then attach together with the Velcro strap.

4. Turn the Waterproof case (or mounting adapter) onto the 1/4-20 screw of the Helmet Mount until secured.

5. Turn the Locking Wheel so it applies pressure to the case to keep the connection secure.

6. Loosen the Tilt Knob, to adjust for the proper aiming angle; then tighten the knob.

7. Please note this helmet mount will only work with vented helmets.

4.Locking Wheel

5.Tilt Knob

5

SHIELD

1. This Mounting Adapter allows you to attach mounting accessories that have a 1/4-20 screw.

2. The camera will clip right in to this adapter.

6

Quick User Guide

7