Before opening the Top Hood, make sure there is no
paper jam or cutter jam trouble. (Read page 3-4,
3-5 and Warranty Limit in the user’s Manual.)
Federal Communications Commission Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
For compliance with Federal Noise Interference Standard, this equipment requires a shielded cable.
This statement will be applied only for the printers marketed in U.S.A.
CE manufacturer’s Declaration of Conformity
(EC Council Directive 89/336/EEC of 3 May 1989)
This product has been designed and manufactured in accordance with the International Standards
EN50081-1/01.92 and EN50082-1/01.92 following the provisions of the Electro Magnetic
Compatibility Directive of the European Communities as of May 1989
Warranty Limits
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happened. Warranty
voids if the user does not follow the instructions in application of this merchandise. The manufacturer is
by no means responsible for any damage or hazard caused by improper application.
About This Manual
This manual is aimed to assist the user to utilize the Aura (PP-5000) series which is a series of
POS thermal printers delicately designed to work with either serial or parallel interface connection. This
manual covers both operational and technical aspects. This manual covers also the Epson emulation
commands and some special features of the printer.
The manufacturer of the Aura (PP-5000) series heartily apologizes to the user for reserving the
right to change or to modify this manual without notice due to the rapid and constant progress and
improvement on science and technology. The user may always obtain the most up to date information
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a
retrieval sys tem, or transmitted in any form or by any means, electronic, mechanical, photocopying, or
otherwise, without the prior written consent of Posiflex Inc. the publisher of this documentation.
Other brand and product names are trademarks and registered trademarks and service marks of
their respective owners.
You have made a very wise decision by purchasing the easy
loading ; low noise ; high resolution ; light weight ; high
reliability thermal printer Aura (PP-5000 & PP-5200) series of
Posiflex products. This series of printers has been elegantly
designed for a Point-Of-Sale, kitchen & kiosk application. The
manufacturer of this printer not only wishes to take this
opportunity to congratulate your smart investment on buying this
printer but also likes to express the wishes for your prosperous
future by using it.
B. PRODUCT BRIEFING
The Aura PP-5000 series (incl. model PP-5200) printer uses
thermal sensitive paper in form of a roll at a width of 58 mm
(standard) or 38 mm (option for PP-5000 only). The Aura PP5000 series printer serves the stand-alone desk top application as
well as the application within a Posiflex integrated POS system
equally perfect.
The Aura PP-5000 series support two types of interface
input through different sub-codes to the model number. The
interfaces are RS232 for serial interface and IEEE1284-A for
parallel interface. Aura printer of different model number subcodes utilizes different cabinet color and accessory cable and
switch setting to accommodate the requirement of different
interface.
The Aura PP-5000 series supports a guillotine type auto
cutter for paper partial cut and a manual cut mechanism. The
1 - 1
Aura series also supports user’s company’s LOGO downloading
for superior performance. It even supports some enhancement
capability for reminder function to persons around. It can be used
to drive a separately purchased kitchen bell for such reminder
function in noisy environment. This printer also supports
application in different countries of various kinds of power
systems by changing the power cord to the power adaptor. The
Aura PP-5000 series make beeping sound as response to Paper
End or Paper Near End signals.
C. UNPACKING
Followings are items you may find when you carefully
unpack the carton that delivers Aura series printer. If there is any
discrepancy or problem, contact your dealer immediately. Be sure
to save the packing materials in case the printer needs to be
shipped at some point in the future.
• The printer itself
‚ Thermal paper roll 58 mm wide
ƒ One of the interface cables:
a Serial cable with 9 pin D sub Female to 8 pin RJ 45 jack for
Aura (PP-5000)S or Aura (PP-5200)S
b Parallel cable with 25 pin D sub Male to 25 pin D sub
Female connectors for Aura (PP-5000)C or Aura (PP-5200)C
Length of the interface cable depends on whether the order
includes the power adaptor. When power adaptor is included, the
interface cable is 6 ft long for stand alone application. When the
power adaptor is not included in the order, the interface cable is a
shorter one for integrated application in Posiflex POS system.
„ One of the power sources:
a Power adaptor + power cord (depend on country type
1 - 2
Power LED
Release
ordered).
b Power supply cable (when no power adaptor ordered)
This printer power supply cable is used to supply power to
the printer from the Posiflex POS system.
… This User’s Manual
D. OPTIONS
• 38 mm paper roll adaptor (for PP-5000 only)
• Kitchen bell (KL-200)
• Language to add to standard model: Japanese Kanji;
Korean; Traditional Chinese or Simplified Chinese, etc..
• Wall mount kit
E. MAIN PARTS ON THE EXTERIOR
Top Hood
Case
Cutter Cover
Hood
Button
Power Switch
1 - 3
FEED Switch
Paper Out LED
Error LED
Parallel Connector
Rear View
Front View
Power Switch
Bottom View
Screws
Serial Connector
Power Connector
Peripheral Connector
Window Plate Screw
Setup Window
1 - 4
F. INDICATORS
• Power LED: green
• Error LED: red
• Paper Out LED: red
II. QUICK START-UP
A. LOADING PAPER
1. Desk top application
1. Press down the hood release button
to release the top hood.
2. Raise the released hood wide open
manually.
3. Drop the thermal paper roll inside
the printer in the orientation as
shown in the picture.
4. Close the hood back leaving the tail
of the paper roll coming out of the
opening between the hood and the
top cover. Tear off excessive paper.
2 - 1
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.