Page 1
HTTP://WWW.PYLEAUDIO.COM
TV TUNER SYSTEM
PLTK120
OWNER,S MANUAL
Page 2
Changing the battery in the remote
1. The remote s battery is held in a small drawer on one edge
of the remote. To open this drawer, press and hold the small
button on the edge of this drawer(as show below) and slide
the drawer out.
2. Insert a new battery and push the drawer back into the remote.
Specifications
,
Signal System
Audio/Video Outputs
TV Channel
Tuner Box, Overall Dimensions
Tuner Box, Weight
Release button
NTSC
Audio R/L 1, Video 1
Channels 2-81
L)5.6 (W)3.6 (H)1.2 inch
0.31Kg
Battery
CONTENTS
Thank you for your purchase.
Please read this User Manual in detail and use the set properly.
Precautions 3
System features and controls 4
Installation and electrical connections 5
+
Remote Function 7
Selecting the input mode 7
Programming channels for TV 7
Selecting channels and adjusting the sound 8
Providing A/V audio to your car radio 8
Changing the remote battery 9
Specifications 9
9
2
Page 3
Precautions
Please read this manual completely and carefully before installing the equipment.
1. Do not operate this equipment while driving, safe driving should always be your highest priority.
2. Do not install these components in an area exposed to rain, moisture, direct sunlight, extreme
heat or cold, excessive dust, dirt or humidity.
3. Immediately unplug the power cord and send the TV Tuner to your local dealer or service center as soon as
possible:
a) If there is smoke or any peculiar odor present during use.
b) If there is damage to any of the component casings.
4. To avoid damage and risk of electronic shock, protect this equipment from getting humid or wet,
If this does occur, unplug the power cord immediately and send the unit to your local dealer
or service center as soon as possible.
5. Do not attempt to repair, open or disassemble any of the components. Dangerous high voltage is present
and may cause an electric shock.
6. Use only a power source with 12 Volts DC (negative ground).
7. Do not place objects on or suspend objects from the power cord, as this may damage the cord.
8. Do not twist or place the power cord near any source of heat in the vehicle.
9. Do not attempt to repair a damaged, broken or deffective power cord. Replace it with a new one immediately.
Selecting channels and adjusting the sound
Use the CH+ and CH- buttons to select channels.
Use the VOL+ and VOL- buttons to increase or decrease audio volume.
You will see a Volume Bar on screen indicating relative volume level.
To disable the audio output, press the MUTE button. To cancel the muting
function, press MUTE button again.
Please note: VOL+, VOL- and MUTE buttons are disabled in AV mode.
Providing A/V audio to your car radio
If your radio has AUX line-level inputs, you can attach the A/V audio output
connectors to these inputs with RCA-RCA interconnect cables.
MUTE
POWER
AVC
AUTO
CH+
VOL-
VOL+
MENU
CH-
TVTUNER
REMOTE
3
8
Page 4
Remote function
1. POWER: Power on/off
2. MENU: In AV mode push the MENU button to access on screen menu.
Use CH- or CH+ button to move on screen point to next or previous
command item. And use VOL+ or VOL- button to increase or decrease
current option value. In TV mode MENU is invalidated.
Selecting the input mode
Tuner can switch between three different video sources using the
remote control. These modes are:
TV Mode: for receiving TV Channels.
AV1: external audio and video inputs for DVD, VCD or video game.
AV2: external audio and video inputs for DVD, VCD or video game.
Programming channels for TV
The tuner system can memorize channels in both TV modes. Press the
AUTO button on the remote, the tuner will begin scanning all of the
available channels and put them into memory.
MUTE
POWER
AVC
AUTO
CH+
VOL-
VOL+
MENU
CH-
TVTUNER
REMOTE
MUTE
POWER
AVC
AUTO
CH+
VOL-
VOL+
MENU
CH-
TVTUNER
REMOTE
MUTE
POWER
AVC
AUTO
CH+
VOL-
VOL+
MENU
CH-
TVTUNER
REMOTE
SYSTEM FEATURES AND CONTROLS
TUNER BOX REMOTE CONTROL
CH+
MENU
CH-
TV TUNER
REMOTE
MUTE
AUTO
VOL+
REMOTE
ANTIN
TV TUNER SYSTEM
AUDIOR
A/VOUTPUT
AUDIOL
VIDEO
DC12V
POWER KEY
AVC KEY
VOL- KEY
CH- KEY
POWER
AVC
VOL-
MUTE KEY
AUTO KEY
CH+ KEY
VOL+ KEY
MENU KEY
7
4
Page 5
Installation and Electrical Connections
Connection
1. Find a suitable location for the tuner unit and mount it securely
in place. Be sure to place it in an area away from moisture and
dirt, and where incoming cables will not be walked on or pulled
accidentally.
2. Make all required audio, video and power connections to the
appropriate connectors on the tuner as indicated in the drawing
below to suit you system installation. Install the infrared remote
eye in a location you know will be available in line-of-sight with
the remote control use location.
Please note that the following drawing describes connections
for all system possibilities and your particular system may vary
from this.
5
INFRARED
REMOTE RECEIVER
REMOTE
TV TUNER SYSTEM
PLTK120
AUDIOR
A/VOUTPUT
AUDIOL
TO DC+12V
TO DC+12V
GROUND
DC12V
ANTIN
VIDEO
6
ANTENNA
POWER
AV
MENU
+
-
AV3
Loading...