PYLE Audio PLDVD128 User Manual

DVD/VCD/CD/MP3PLAYERDVD/VCD/CD/MP3PLAYER

Receiption collection
Speaker collection

Install the unit
Remove the unit

Power
Volume
Eject
Release
Mode
Loud
L/R
Clock
Dsp

Volumesetting
Bass setting
Treble setting
Balance setting
Fadersetting

Play/Pause
Scan
Repeat
Random
Stop

N/P

Band
Band tuner

Loading and Replacingthebattery
Basic operation

1

CAUTION

Do not operatewhendriving.
Toprevent electric,etc,Please donot

let

the metal goods(silver,coin,tools..)fallinto

the installation.

If you smellorsee smoke,turn offthe

power immediately andconsultour dealer.

Be careful nottodrop or shocktheunit

strongly.

Do not touchtheliquid crystal toavoidthe
life hurt.If theclothesis stained withit,Please
clean it immediatelybysoap.

Foryour driving safety,pleaselink your
brake detecting wirewithlow power
level,and keep itcontrolledby manual brake
switch.when driving acar,the brake wireshall
be high powerleveland now,unitcan not
play DVD or VCDdisc.

Be sure theunitis connected toa12V

DC power withaNegative Ground.

Do not installtheunit in placeswhere
it is exposedtodirect sunlight,high heat
or humidity,watersplashor dust.

Tochange fuse,please usethesame

one in specificationandcapacity.

When changing fuse,pleasedoit
after pulling downpowerwires to avoid
short circuit.

If the unitseemsnot work inproper
situation,please press theresetbutton to
resume the function.

2

RED

Tofront left
speaker

Tofront right
speaker

Torear left
speaker

Torear right
speaker

3

Before installing thereceiverpermanently, fititin the approximateplacein your car,andconnect the
equipment according tothespeakers and electricalconnections.When
your system isoperatedproperly,(preferably withthe
car engine running),followthe instructions
for permanent installation

3)Support strap
(supplied)

of your system.

1)Install half sleeve, canbewithor
without adapter.Itwillfitbetter
with adapter.

2)Bend over some tabstosecurethe
half sleeve inside ofdash.

3) Support strap tobestruttedunder
dash, secure this striptoavoidskipp
ing of disc.

Insert removal wrench intothesmall
gap on the rightsideoftheunitand pull
the unit slightly outonthesameside,
then release the wrench.Repeatthe
same action for theleftside.Bynow,
you can remove theunitandunplug
the wires connector.

2)Bend over tabs
of half sleeve

(supplied)

4) Two wrenches forreleasing
the unit (supplied)

1) Adapter
(not supplied)

Half sleeve
(supplied)

4

Selecting radio and play

Each time you pressthekey,it will switchbetweenradio
position and disc position.

DSP

press the DSP button to emphasize thebassoutput,
press it again toresumethenormallistening.

In VCD mode, press [BAND] button,itwillswitchbetween
right channel and leftchannelposition.

Short press CLKcandisplay time even poweroff .
Long Press CLKfor3 seconds willenter set mode.

Rotate the SEL/VOLbuttonto set thehour.

Press the SEL/VOLbutton,andthen rotate ittoset

the minute.

there is nooperationin 5 seconds,itwill quit clock
set mode.

6

SELECT VOLUME

PWR

VOL

SEL

SEEK

BAND CLOCK

RPT RDM

DSP

SCN

234

1

STOP N/P

5

6

MODE

Press SEL/VOL buttononce,displaywill show VOL
on,then rotate thebuttonin clockwise directionto
increase volume level;rotatethebutton in
anticlockwise direction to
decrease volume level.

VOL

SEL

Press SEL/VOL buttontwice,displaywill show BAS
on,then rotate thebuttonto adjust basslevelup/down
in different direction.

PLAY/PAUSE

SCAN

REPEAT

RANDOM STOP

N/P

Press SEL/VOL buttonthird,
display will show TRE on,
then rotate thebuttonto adjust treblelevelup/down
in different direction.

Press SEL/VOL buttonfourth,
display will show BAL on,
then rotate thebuttonto adjust
left and rightspeakerslevel up
/down in differentdirection.

Press SEL/VOL buttonfifth,displaywill show FAD
on,then rotate thebuttonto adjust frontandrear
speakers level up/downindifferent direction.

7