PYLE Audio PLD3MU User Manual
PLD3MU
3'' TFT Touch Screen DVD/ VCD/ CD/ MP3/ CD-R/ USB/ AM/ FM
www.pyleaudio.com
Contents
Safety Precautions......................................................2
Electric Connection ............................................... .....3
Reception collection
Speaker collection
Installation.................................................................4
Install the unit
Remove the unit
General Features........................................................5
PLAY/PAUSE
Eject
Source/Power
Mute
Volume
Select charter/Foward /Backward
Repeat
Release
Display position adjustment
USB/SD operation......................................................8
USB/SD PLAYER
System setting.....................................................9
Video
Audio
System
Radio Operation..................................................10
Band
Band tuner
APS/ST/RDS
Remote Control....................................................11
Loading and Replacing the battery
Basic operation
Accessories........................................................14
Specifications.....................................................15
Trouble Shooting.................................................16
1
Safety precautions
CAUTION
To prevent injury or fire, please
take the precautions:following
Do not watch videos when driving.
To prevent electric shock, etc. please do
not let
the metal goods(silver,coin,tools..)
fall into the installation.
If you smell or see smoke, turn off the
power immediately and consult the place
of purchase.
Be careful not to drop or shock the unit
strongly.
Do not touch the liquid crystal to avoid
hurting yourself. If your clothes are stained
by it, please clean them with soap
immediately.
For your driving safety, please link your
brake detecting wire with low power
level, and keep it controlled by manual
brake switch. wire should be high power
level and the unit can not play DVD or
VCD disc.
WARNING
To prevent damage to the machine,
take the following precautions:
Be sure the unit is connected to a 12V
FM
DC power with a Negative Grou
Do not install the unit in places where
it is exposed to direct sunlight, high heat
or humidity, water splash or dust.
To change fuse, please use the same
one in specification and capacity.
When changing fuse, please do it
after pulling down power wires to avoid
short circuit.
If the unit does not seem to be working
properly, please press the reset button to
resume the function.
PRECAUTIONS
Please Note:
When driving a car, reduce the
volume to be more aware of the
road traffic.
Avoid getting the speakers and
disc wet from water or dampness
while cleaning the car.
Do not park your car in the direct
sunlight and turn on the unit after it is
cooling down in the car.
Protect your mechanism, and do not
put it close to magnet, screwdriver or
other cohere stuff.
If you do not comply with the above
items, it may cause abnormal running
and system trouble.
2
Electric Connection
VIDEO IN
BACK ACAR VIDEO IN
(YELLOW)
()YELLOW
AUX RIGHT IN
(RED)
(WHITE)
AUXLEFTIN
SUBWOOFER
10
BROWN
FRONT LEFT RCAOUT
FRONT RIGHTRCA OUT
VIDEO OUT
Brake detecting wire
Detecting wire for back a car
Remote control for amplifier.
Connect control for antenna
Ignition key
sw tchi
Car fuse box
(Main fuse)
Battery
(WHITE)
(RED)
(YELLOW)
Gray
Gray
Gray
Gray
Brown
Pink
BLUE
Ignition wire(Red)
Battery wire(Yellow)
Ground wire(Black) (To car chassis)
33
Front.L
Front.R
Rear.L
Rear.R
FM/AM antenna input
Fuse(10A)
Orange
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Light wire
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
Installation
Before installing the receiver, fit it in the suitable place of your car.
Then connect the corresponding speakers and electrical connections.
When your system is operated properly, follow the instructions installation
INSTALL THE UNIT
1)Install the bracket
2)Bend over some slices to secure the
installation of bracket inside of dash.
3)To avoid shake of the receiver, make
sure to install the fixation strap behind
the receiver.
2)Bend over the slices
(supplied)
1) Adapter
(not supplied)
REMOVE THE UNIT
Insert the keys into the small gaps in
the right and left sides of the unit at
the same time. Link the keys to the
slices and then pull out the unit lightly
to remove it from your car, and then
pull out the connection plugs.
Slices
(supplied)
3) Two keys for releasing
the unit (supplied)
4
General Features
BAND
SOURCE
BAND
SRC/PWR
APS/
CLK/
CLK/
VOL
/APS
MENU
IR
VOL
MENU
MUTE
MUTE
ST/RPT
ST/RPT
5
Loading...