www.pyleaudio.com
CAUTION
OPERATING INSTRUCTIONS
PICD65I
PLL
DIGITAL
TUNER
iPod/iPhone Flat Panel Motorized
Vertical FM Radio CD Sound System
BLUE
BACKLIGHT
DISPLAY
REMOTE
CONTROL
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash
and arrowhead
within the triangle
is a warning
sign alerting you of
"dangerous voltage"
inside the product.
WARNING: To reduce
the risk of electric shock, do
not remove cover (or back).
No user-serviceable
parts inside. Refer
servicing to qualified
service personnel.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.
THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN
READILY OPERABLE. TO COMPLETELY DISCONNECT THE POWER INPUT, THE MAINS
PLUG OF THE APPARATUS MUST BE DISCONNECTED FROM THE MAINS COMPLETELY.
THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED
DURING INTENDED USE.
PLEASE NOTE: YOU WILL FIND THE
RATING LABEL FOR THIS PRODUCT
LOCATED ON THE REAR OF THE UNIT.
CAUTION: GROUNDING OR POLARIZATION. THE PRECAUTIONS
SHOULD BE TAKEN SO THAT THE WIDER BLADE OF THE AC PLUG
MUST MATCH THE SLOT IN RECEPTACLE "WALL SOCKET".
NOTE: CAUTION SYMBOLS ARE PRINTED ON REAR OF UNIT.
PLEASE REFER TO INSTRUCTION MANUAL.
CAUTION:
INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
UNSICHTBARE LASERSTRAHLUNG TRITT AUS,
VORSICHT:
WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZENI.
OSYNLIG LASERSTRÁLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
VARNING:
SPÄRR ÄR URKOPPLAND. STRÁLEN ÄR FARLIG.
USYNLIG LASERSTRÁLING VED ÁBNING. NÁR
ADVARSEL:
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÁ UDS/ETTELSE FOR
STRÁLING.
ATTNENZIONE:
DIRETTAMENTE NELLA SORGENTE DEL LASER.
ACHTUNG:
AVISO:
RADIONS LASER INVISIDILE. NON GUARDARE
LASERLINSE NICHT BERÜHREN UNSICHTBARER LASERSTRAHL.
A LENTE NUNCA DEVE SER TOCADA.
E-2
The exclamation
point within the
triangle is a warning
sign alerting you of
important instructions
accompanying the
product.
CAUTION
DO NOT EXPOSE TO DRIPPING
OR SPLASHING LIQUIDS!
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LASER DE CLASSE
LASER DI PRIMA CLASSE
KLASSE 1 LASER
LASER PRIMERA CLASE
LASER CLASSE 1
KLASSE 1 LASER PRODUKT
IMPORTANT SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS -
is operated.
2. RETAIN INSTRUCTIONS -
reference.
3. HEED WARNINGS -
4. FOLLOW INSTRUCTIONS -
5. CLEANING -
aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACHMENTS -
may cause hazards.
7. WATER AND MOISTURE -
wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES -
The product may fall, causing serious injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer's instructions, and should
use a mounting accessory recommended by the manufacturer.
9.
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may causethe appliance and cart
combination to overturn.
10. VENTILATION -
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instruction have been adhered to.
11. POWER SOURCES -
on the marking label. If you are not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended to operate from battery power, or
other sources, refer to the operating instruction.
12. GROUNDING OR POLARIZATION -
alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarizes plug.
ALTERNATE WARNINGS -
having a third (grounding) pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact you electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. POWER-CORD PROTECTION -
be walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and point where they exit from the product.
14. PROTECTIVE ATTACHMENT PLUG -
overload protection. This is a safety feature. See Instruction Manual for replacement or resetting
of protective device. If replacement of the plug is required, be sure the service technician has used
a replacement plug specified by the manufacturer that has the same overload protection as the
original plug.
15. OUTDOOR ANTENNA GROUNDING -
the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
All the safety and operating instruction should be read before the product
The safety and operating instruction should be retained for future
All warning on the product and in the operating instructions should be adhered to.
All operating and use instructions should be followed.
Do not use attachments not recommended by the product manufacturer as they
Do not use this product near water- for example, near a bath tub,
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
Slots and openings in the cabinet are provided for ventilation
This product should be operated only from the type of power source indicated
This product may be equipped with a polarized
This product is equipped with a three-wire grounding-type plug, a plug
Power supply cords should be routed so that they are not likely to
The product is equipped with an attachment plug having
If an outside antenna is connected to the receiver, be sure
SEE FIGURE:
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC - NATIONAL ELECTRICAL CODE
16. LIGHTNING -
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to lightning and power-line
surges.
17. POWER LINES -
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18. OVERLOADING -
receptacles as this can result in a risk of fire or electric shock.
19. OBJECT AND LIQUID ENTRY -
as they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
20. SERVICING -
expose you to dangerous voltage or other hazards, Refer all servicing to qualified service personnel.
21. DAMAGE REQUIRING SERVICE -
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally be following the operating instructions. Adjust only
e) If the product has been dropped or damaged in any way, and
f ) When the product exhibits a distinct change in performance -
22. REPLACEMENT PARTS -
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards,
23. SAFETY CHECK -
technician to perform safety checks to determine that the product is in proper operating condition.
24. WALL OR CEILING MOUNTING -
recommended by the manufacturer.
25. HEAT -
stoves, or other products (including amplifiers) that produce heat.
For added protection for this product during a lightning storm, or when it is left
An outside antenna system should not be located in the vicinity of overhead
Do not overload wall outlets, extension cords, or integral convenience
Never push objects of any kind into this product through openings
Do not attempt to service this product yourself as opening or removing covers may
Unplug this product from the wall outlet and refer servicing to
those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to damage and will often require extensive work by a qualified technician to restore
the product to its normal operation.
this indicates a need for service.
The product should be situated away from heat sources such as radiators, heat registers,
When replacement parts are required, be sure the service technician
Upon completion of any service or repairs to this product, ask the service
The product should be mounted to a wall or ceiling only as
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
E-3
E-4
TOP VIEW:
FRONT VIEW:
BACK VIEW:
1
3
4
5
678 9 10
18
19
LOCATION OF CONTROLS
1. DESK STAND
2. CAVITY FOR DOCK ADAPTOR
3. CD DOOR (MOTORIZED)
4. SPEAKERS (LEFT & RIGHT)
5. ON/ STANDBY KEY
6. OPEN/ CLOSE KEY
7. FUNCTION KEY
8. PROGRAM/ PLAY MODE KEY
9. EQ/ MEM-UP KEY
10. BLUE BACKLIT DISPLAY
11. REMOTE CONTROL SENSOR
2
4
11
13 141516
12
12. PLAY/ PAUSE/ FM MODE KEY
13. STOP/ CLOCK SET KEY
NEXT/ HOUR/ MIN. UP KEY
14.
15. BACK/ HOUR/ MIN. DOWN KEY
16. VOLUME DOWN ( ) KEY
17. VOLUME UP ( ) KEY
18. BACK UP BATTER COMPARTMENT
19. FM ANTENNA WIRE
20. DOCK VIDEO OUT SOCKET
21. AUX INPUT SOCKET
22. AC CORD & PLUG
17
20
21
22
REMOTE CONTROL - LOCATION OF CONTROLS:
1. ON/ STANDBY KEY
3
4
2
1
5
9
13
17
23
8
7
6
10
11
12
15
16
14
19
20
18
21
22
26
25
24
28
27
2. DISPLAY KEY
3. CLOCK SET KEY
4. MUTE KEY
5. EQ KEY
6. TIMER KEY
7. RADIO MEM. + KEY
8. VOL. UP + KEY
9. PROGRAM KEY
10. SLEEP KEY
11. RADIO MEM. - KEY
12. VOL. DOWN - KEY
13. BACK KEY
14. PLAY/ PAUSE KEY
29
15. NEXT KEY
16. CD KEY
17. PLAY MODE KEY
18. STOP KEY
19.FMMODEKEY
20. TUNER KEY
21. iPod MENU UP KEY
22. AUX KEY
23. iPod BACK KEY
24. iPod SELECT KEY
25. iPod NEXT KEY
26. DOCK KEY
27. iPod DOWN KEY
28. MENU KEY
29. BATTERY COMPARTMENT
POWER SUPPLY
- THIS SET WORKS ON NORMAL HOUSEHOLD AC-POWER.
- MAKE SURE THE SET VOLTAGE OF THE UNIT MATCHES YOUR LOCAL VOLTAGE.
- INSERT THE PLUG OF THE AC-CORD INTO A WALL OUTLET WITH AC-POWER.
- PRESS THE ON/ STANDBY KNOB TO SWITCH “ON” THE UNIT.
WHEN THE POWER IS “ON” THE ENTIRE DIGITAL DISPLAY WILL BE LIT UP WITH
A “BLUE” BACK-LIGHT. THIS INDICATES THE HI-FI IS SWITCHED “ON”.
IMPORTANT : HOW TO TELL IF POWER IS "ON" ?
BACK UP BATTERIES
- OPEN THE BATTERY DOOR AT THE REAR OF UNIT.
- INSERT 2 PCS "AAA-CELL" (UM-4/LR03 TYPE) BATTERIES IN THE BATTERY COMPARTMENT.
THESE 2 BATTERIES ARE FOR BACKUP OF THE "REAL TIME CLOCK" AND "RADIO
MEMORY PRESET STATIONS DURING BRIEF POWER OUTAGES". PLEASE OBSERVE THE
CORRECT POLARITIES OR THE MEMORY WILL NOT BE PROPERLY MAINTAINED.
PREPARATION OF REMOTE CONTROL
- REMOVE (GENTLY PULL OUT) THE PLASTIC "TAB" FROM THE BATTERY
COMPARTMENT AT THE REAR OF THE REMOTE CONTROL.
- TEST THE REMOTE CONTROL BY PRESSING THE ( ON/ STANDBY) KEY TO
CHECK THAT THE UNIT SWITCHES ON PROPERLY USING THE REMOTE CONTROL.
E-5
E-6
DIGITAL CLOCK FUNCTION
- THE SET HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED IN 2 SITUATIONS:
(1) WHEN THE SET IS IN "STANDBY MODE". (THE DISPLAY WILL CONTINUOUSLY
SHOW THE CURRENT TIME). IN THIS SITUATION THE BLUE BACKLIGHT
IS NORMALLY DIMMED (TO SAVE ELECTRICITY) BUT YOU CAN SWITCH ON
THE BLUE DISPLAY LIGHT BY PRESSING THE "CLOCK SET" KEY OR "TIMER" KEY
ON REMOTE CONTROL. THIS WILL ACTIVATE THE BLUE LIGHT FOR
APPROXIMATELY 10 SECONDS.
(2) WHEN THE SET IS IN "ON MODE" (THE BLUE LIGHT OF THE DISPLAY IS "ON" IN
THIS MODE, TO INDICATE THAT THE SET IS POWERED "ON"). IN THIS SITUATION
THE LCD DISPLAY NORMALLY DOES NOT AUTOMATICALLY SHOW THE CURRENT
TIME. BUT YOU CAN PRESS THE "DISPLAY" KEY (ON REMOTE CONTROL)
TO SEE THE CURRENT TIME.
HOW TO SET CORRECT TIME:
SWITCH UNIT TO "STAND-BY" MODE (DISPLAY LIGHT = DIMMED)
PRESS & HOLD CLOCK SET KEY UNTIL THE "HH" HOUR DISPLAY IS
FLASHING.
PRESS NEXT OR BACK REPEATEDLY TO SET THE CORRECT
IN THE DISPLAY & PRESS THE CLOCK SET KEY TO CONFIRM.
PRESS NEXT OR BACK REPEATEDLY TO SET THE CORRECT
IN THE DISPLAY & PRESS TO CONFIRM.MINUTE
CLOCK SET KEY
CORRECT TIME IS NOW SET & WILL BE SHOWN IN THE DISPLAY.
HOUR
AUTOMATIC POWER ON/OFF TIMER FUNCTION
- THIS SET HAS A TIMER FUNCTION TO ENABLE YOU TO PROGRAM THE UNIT TO
AUTOMATICALLY SWITCH “ON” OR “OFF” AT PRESET TIMES. THIS IS USEFUL AS A MORNING
ALARM CLOCK :
HOW TO SET TIMER
1. PRESS AND HOLD TIMER KEY (ON REMOTE CONTROL). THE SYMBOL
APPEARS IN THE DISPLAY.
2. PRESS NEXT OR BACK TO ADJUST THE HOUR OF THE DESIRED "ON" TIME
AND THEN PRESS TIMER KEY TO CONFIRM.
3. PRESS NEXT OR BACK TO ADJUST THE MINUTES OF THE DESIRED "ON" TIME
AND THEN PRESS TIMER TO CONFIRM.
4. NOW THE WORDING IN THE DISPLAY CHANGES TO SHOW .
5. PRESS NEXT OR BACK TO ADJUST THE HOUR OF THE DESIRED "OFF" TIME
AND THEN PRESS TIMER TO CONFIRM.
6. PRESS NEXT OR BACK TO ADJUST THE MINUTES OF THE DESIRED "OFF" TIME
AND THEN PRESS TIMER TO CONFIRM.
7. NOW THE DISPLAY WILL INDICATE THE "WAKE UP MODE" (iPod OR RADIO OR CD).
PRESS NEXT TO CHOOSE THE DESIRED MODE & PRESS TIMER TO CONFIRM.
8. THE DISPLAY THEN SHOWS THE "WAKE UP VOLUME LEVEL" (LOUDNESS).
PRESS BACK OR NEXT TO DECREASE OR INCREASE THE VOLUME LEVEL TO BE
USED FOR THE MUSIC TO BE PLAYED WHEN THE TIMER SWITCHES ON THE UNIT AT THE
PRE-SET TIME.
9. PRESS TIMER TO CONFIRM.
10. FINALLY THE UNIT WILL RETURN TO THE NORMAL DISPLAY, EXCEPT THAT THE
SYMBOL WILL BE SHOWN, TO INDICATE THAT YOU HAVE PROGRAMMED A ON/OFF ALARM
SETTING.
11. IN CASE YOU WISH TO DISABLE THE TIMER, PRESS THE TIMER KEY ONCE,
(NOTE : THE AUTOMATIC ON/OFF TIMER WILL SWITCH ON THE UNIT AS IF YOU HAVE
MANUALLY PRESSED THE “ON/ STANDBY” KEY. IF YOU HAVE SELECTED "WAKE TO RADIO",
THE EXACT PRESET RADIO BAND & STATION WILL BECOME ACTIVATED WHEN POWER
SWITCHES ON).
TIMER
& THE SYMBOL WILL DISAPPEARS.
ON TIME
OFF TIME
TIMER
AUTOMATIC POWER OFF SLEEP FUNCTION
- THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH CAN AUTOMATICALLY
SWITCH OFF THE UNIT. THIS IS USEFUL FOR SLEEPING TO MUSIC AT NIGHT.
- AT ANY TIME WHILE THE UNIT IS OPERATING, PRESS KEY
(ON REMOTE CONTROL) REPEATEDLY TO CHOOSE THE AUTOMATIC
POWER OFF TIME.
90
MINS80MINS70MINS60MINS50MINS
40
MINS30MINS20MINS10MINS
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
SLEEP
OFF*
E-7
E-8
ELECTRONIC VOLUME CONTROL
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS
THE VOLUME UP (VOL +) OR VOLUME DOWN (VOL -) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOUDNESS.
- SOMETIMES, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WHEN YOU ARE INCREASING OR
DECREASING THE VOLUME. THIS IS A NORMAL CONDITION & THE SOUND WILL
DISAPPEAR WHEN YOU RELEASE THE VOLUME KEY (WHEN YOU REACH THE
DESIRED VOLUME LEVEL).
(PUSH BUTTON TYPE)
OPERATION OF RADIO
- PRESS THE "ON/OFF" KEY ONCE TO SWITCH ON THE UNIT.
- PRESS THE KEY (ON UNIT) REPEATEDLY UNTIL THE DISPLAY
SHOWS "FM" .
- TO IMPROVE FM-RADIO RECEPTION, FULLY EXTEND THE FM-ANTENNA WIRE
AND ADJUST IT'S POSITION.
- USE THE "FM MODE" KEY (ON REMOTE CONTROL) TO SELECT THE
DESIRED MODE ( . IN SOME CASES, WHERE RECEPTION IS
POOR, IT MAY BE ADVISABLE TO SELECT “MONO” MODE, TO IMPROVE CLARITY
OF THE RADIO SIGNAL.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
- PRESS (AND IMMEDIATELY RELEASE) THE KEY OR
KEY TO “SCAN” (MANUALLY ADJUST) THE RADIO FREQUENCY “UP” OR “DOWN”
BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH
STEP’S POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED
INTO ONE OF THE “MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
- PRESS AND HOLD (FOR 2 SECONDS) THE OR KEYS
TO “SEEK” (AUTOMATICALLY ADJUST) THE RADIO FREQUENCY “UP” OR “DOWN”
TO THE NEXT AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE
NEXT STATION THAT IS FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
“MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
RADIO MEMORY (STATION PRESET MEMORY STORAGE)
- AT ANY TIME, THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE
STORED INTO ONE OF THE MEMORY POSITION.
- PRESS KEY ONCE.
- PRESS OR KEY ON THE REMOTE CONTROL TO SELECT
DESIRED MEMORY POSITION. (THERE ARE 30 MEMORY POSITIONS FOR FM BAND).
- PRESS KEY ONCE TO SAVE THE SELECTED STATION INTO THE
SELECTED MEMORY POSITION.
- TO RECALLANY SAVED MEMORY, SIMPLY PRESS ,
THE SAVED RADIO-BAND WILL BE RECALLED.
- TO CLEAR THE MEMORY OF ANY POSITION, SIMPLY SAVE A NEW STATION TO
THE SAME MEMORY POSITION.
FUNCTION
OR PRESS THE "TUNER" KEY ONCE ON REMOTE CONTROL
FM MONO/STEREO)
NEXT BACK
NEXT BACK
PROGRAM
RADIO M+
PROGRAM
RADIO M-
RADIO M+ RADIO M-
E-9
OR
OPERATION WITH THE iPod/ iPhone
THIS UNIT IS DESIGNED TO ALLOW YOU TO CONNECT AN WITHOUT THE
NEED FOR DOCK CONNECTORS. THE DESIGN OF THE UNIT HAS BEEN STRUCTURED
TO PROVIDE SUPPORT TO TE CONNECTOR UNDER NORMAL USAGE WITHOUT EXCESSIVE
PRESSURE ON THE WHEN CONTROLLING PLAYBACK USING THE
SCREEN.
- TURN ON BOTH THE UNIT AND THE iPod/ iPhone.
- PRESS THE KEY REPEATEDLY UNTIL THE DISPLAY SHOWS “iPod”
OR SIMPLY PRESS THE "DOCK" KEY ON REMOTE CONTROL.
- THE UNIT WILL AUTOMATICALLY START PLAYBACK OF THE SONGS.
- THE iPod DISPLAY WILL INDICATE THE INFORMATION OF THE CURRENT
SONG (TRACK).
- AT ANYTIME DURING PLAYBACK, PRESS THE KEY
TO PAUSE OPERATION OF THE UNIT. PRESS KEY TO RESUME
OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS & HOLD THE KEY
TO STOP PLAYBACK OF UNIT.
- AT ANYTIME DURING PLAYBACK, PRESS AND RELEASE THE
BACK/ TUNE -
CONTROL) TO SKIP FORWARD OR BACKWARDS BY ONE TRACK, AS DESIRED.
- ANY ANYTIME DURING PLAYBACK, PRESS AND HOLD THE
BACK/ TUNE -
CONTROL) TO FAST-FORWARD (CUE) OR FAST-REVERSE (REVIEW)
THE SPECIFIC TRACK, WHICH IS CURRENTLY PLAYING.
- YOU CAN OPERATE THE iPod USING EITHER THE SET, REMOTE CONTROL
OR DIRECTLY WITH THE iPod ITSELF.
- WHEN THE iPod HAS BEEN CONNECTED WITH THE UNIT, IT WILL START
CHARGING THE BATTERY OF THE iPod .
- NEVER REMOVE (OR UNPLUG) THE iPod/ iPhone FROM THE SET DURING PLAYBACK,
ALWAYS PRESS & HOLD FOR 2 SECONDS THE KEY FIRST AND THEN
PRESS THE KEY TO SWITCH TO ANOTHER SOURCE (EG. “RADIO”
OR “AUX”) BEFORE REMOVING OR UNPLUGGING THE iPod/ iPhone,
TO PREVENT DAMAGE TO YOUR SONG FILES OR MEMORY DEVICES.
"Made for iPod," "Made for iPhone," mean that an electronic accessory has
been designed to connect specifically to iPod, iPhone, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the operation
of this device or its compliance with safety and regulatory standards. Please note that the use
of this accessory with iPod, iPhone may affect wireless performance.
iPod/ iPhone iPod/ iPhone
FUNCTION
/ iPhone
KEYS ON UNIT (OR "iPod NEXT/ iPod BACK" KEY ON REMOTE
KEYS ON UNIT (OR "iPod NEXT/ iPod BACK" KEY ON REMOTE
/ iPhone
/ iPhone
FUNCTION
/ iPhone
/ iPhone
REPEAT PLAYBACK FUNCTION (iPod/ iPhone)
- AT ANYTIME DURING iPod/ iPhone PLAYBACK:
3D-VIRTUAL SURROUND
- PRESS THE "PLAY MODE" KEY ON REMOTE CONTROL OR
PRESS THE FOLLOWING SYMBOLS ON THE iPod/ iPhone SCREEN:
= TO REPEAT THE CURRENT TRACK
= TO REPEAT ALL TRACKS
E-10
iPod/ iPhone
PLAY/PAUSE
PLAY/PAUSE
PLAY/PAUSE
PLAY/PAUSE
NEXT/ TUNE +
NEXT/ TUNE +
OR
OR
SHUFFLE (RANDOM) PLAYBACK FUNCTION (iPod/ iPhone)
- THIS UNIT IS ABLE TO SHUFFLE ALL SONGS ON AN iPod/ iPhone AND PLAY THEM
BACK IN "RANDOM" ORDER.
- TO ACTIVATE THIS FUNCTION, SELECT THE SHUFFLE ICON " " (ON THE iPod/ iPhone).
- THE " " SYMBOL WILL BE DISPLAYED ON THE iPod SCREEN &
SHUFFLE / iPhone
THE SONGS WILL BE PLAYED IN RANDOM ORDER.
iPod VIDEO OUT
YOU CAN CONNECT THE iPod/ iPhone VIDEO OUT SOCKET TO THE VIDEO INPUT
TERMINAL OF YOUR TV TO WATCH VIDEO PROGRAMS FROM YOUR iPod/ iPhone
ON YOUR TV SCREEN.
* NOTE: THIS UNIT DOES NOT SUPPORT VIDEO-JOUT FROM THE iPhone 4.
INSERTION AND REMOVAL OF DISCS
PRESS THE "FUNCTION" KEY (ON UNIT) REPEATEDLY UNTIL THE DISPLAY
SHOWS "CD" OR PRESS "CD" KEY ONCE ON REMOTE CONTROL.
PRESS THE OPEN/ CLOSE KEY TO OPEN THE CD-DOOR. CAREFULLY PLACE
A COMPACT DISC ONTO THE CENTER SPINDLE WITH THE LABEL SIDE (PRINTED
SIDE OF DISC) FACING OUTWARDS (TOWARDS YOU).
PRESS THE "OPEN/ CLOSE" KEY TO AUTOMATICALLY CLOSE THE CD-DOOR.
THE CD-DISPLAY WILL BRIEFLY SHOW THE TOTAL NUMBER OF TRACKS ON THE DISC
AFTER A FEW SECONDS. THE CD IS NOW READY TO BE PLAYED.
TO REMOVE A DISC, PRESS THE OPEN/ CLOSE KEY. THE DOOR WILL OPEN
UPWARDS ALLOWING THE REMOVAL OF THE CD INSIDE.
IMPORTANT:
SMUDGES OR DIRT ONTO THE SURFACE OF A DISC. IN CASE THIS HAPPENS,
USE A SPECIAL CD-CLEANING CLOTH OR CLEANING KIT TO REMOVE THE DIRT OR
SMUDGES.
- THIS UNIT HAS A MOTORIZED (MOTOR OPERATED) AUTOMATIC CD-DOOR.
- PLEASE NEVER TRY TO OPEN OR CLOSE THE DOOR MANUALLY (BY HAND)
- ALWAYS USE THE CD OPEN / CLOSE KEY
- WHEN OPENING, THE DOOR WILL SWING UPWARDS AND STOP AUTOMATICALLY
- IF THERE IS ANY OBSTRUCTION WHEN OPENING THE DOOR (IF SOMETHING
ALWAYS HOLD A CD BY IT'S EDGES. AVOID GETTING ANY FINGER-PRINTS,
MOTORIZED AUTOMATIC CD-DOOR - OPERATION AND PRECAUTIONS
IMPORTANT
WHEN IT IS FULLY OPEN. NEVER APPLY PRESSURE ON THE DOOR TO OPEN
THE DOOR FASTER OR BEYOND ITS LIMIT.
IS BLOCKING THE DOOR AND PREVENTING IT FROM OPENING) THE DOOR WILL
AUTOMATICALLY STOP AND REVERSE DIRECTION (CLOSE) AFTER 4-5 SECONDS
TO PREVENT DAMAGE TO THE CD-DOOR AND MOTOR.
NORMAL CD OPERATION
- PRESS " " KEY TO SWITCH ON THE UNIT.
ON/ STANDBY
- PRESS THE " " KEY (ON UNIT) REPEATEDLY UNTIL THE DISPLAY SHOWS
"CD" OR PRESS THE " " KEY ON REMOTE CONTROL.
- PRESS THE " " KEY & INSERT A CD AS DESCRIBED.
- PRESS KEY IF PLAYBACK DOESN'T AUTOMATICALLY BEGIN.
THE DISK WILL START SPINNING & THE FIRST SONG (TRACK) WILL START PLAYING.
THE DISPLAY WILL INDICATE THE CURRENT TRACK NO.
- AT ANY ANYTIME DURING PLAYBACK, PRESS THE KEY
TO PAUSE OPERATION OF THE UNIT. PRESS KEY TO RESUME
OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS THE KEY TO STOP OPERATION
OF THE SET. THIS WILL RESET THE SET TO THE FIRST TRACK (IF YOU PRESS
PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS START PLAYING).
- AT ANYTIME DURING PLAYBACK, PRESS AND RELEASE THE OR
KEYS TO SKIP FORWARD OR BACKWARDS BY ONE TRACK, AS DESIRED.
- ANY ANYTIME DURING PLAYBACK, PRESS AND HOLD THE OR
KEYS TO FAST-FORWARD (CUE) OR FAST-REVERSE (REVIEW) THE SPECIFIC
TRACK, WHICH IS CURRENTLY PLAYING.
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO 20
TRACKS, AS DESIRED.
- ALWAYS PRESS THE KEY BEFORE STARTING THE PROGRAMMING.
1. SWITCH ON THE SET AND SELECT "CD" FUNCTION. THEN PRESS KEY.
2. PRESS KEY ONCE.
3. PRESS AND KEYS TO SELECT THE TRACK (SONG) NUMBER IN THE
CURRENT MEMORY POSITION (AS DISPLAYED ON THE SCREEN).
4. PRESS KEY. THIS SAVES THE SELECTED SONG INTO THE PREVIOUS
MEMORY POSITION AND ADVANCES THE MEMORY POSITION TO THE NEXT NUMBER
SO THAT YOU CAN SAVE ANOTHER SONG IN THIS POSITION.
5. REPEAT STEP (3) AND (4), EACH TIME SELECTING ANY TRACK (SONG) NUMBER OF
YOUR CHOICE TO BE STORED IN SUCCESSIVE PROGRAM MEMORY POSITIONS.
MAKE SURE TO PRESS KEY EACH TIME.
6. AFTER A MAXIMUM OF 20 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED,
PRESS THE KEY TO START PLAYING YOUR PROGRAMMED SEQUENCE OF
SONGS.
7. TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS KEY TWICE. THIS WILL RESET THE MEMORY AND CLEAR
THE PROGRAM.
FUNCTION
OPEN/ CLOSE
PLAY/PAUSE
PROGRAM
NEXT
PROGRAM
PLAY
STOP
CD
STOP
BACK
PROGRAM
PLAY/PAUSE
PLAY/PAUSE
STOP
NEXT BACK
NEXT BACK
STOP
MUSIC EQUALIZER
- ANYTIME DURING CD PLAYBACK, PRESS THE KEY (ON REMOTE CONTROL)
REPEATEDLY TO CHOOSE THE DESIRED SOUND EFFECT ACCORDING TO THE
MUSIC YOU ARE LISTENING TO :
CLASSIC
ROCK
POP
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
EQ
JAZZ
*OFF
E-11 E-12
REPEAT PLAYBACK FUNCTION
- AT ANYTIME DURING PLAYBACK:
3D-VIRTUAL SURROUND
- PRESS P-MODE KEY
REPEATEDLY TO SELECT:
PRESS ONCE = REPEAT ONE: TO REPEAT THE CURRENT TRACK
PRESS TWICE = REPEAT ALL:
PRESS THREE = RANDOM:
(SAME AS PLAY MODE KEY ON REMOTE CONTROL)
(DISPLAY FLASHES "REP")
(DISPLAY SHOWSS "REP")
(DISPLAY SHOWS "RAND")
TO REPEAT ALL TRACK
TO SHUFFLE ALL SONGS ON A DISC.
MUTE FUNCTION
- THIS SET HAS A MUTE FUNCTION TO ENABLE YOU TO TURN OFF THE VOLUME
TEMPORARILY.
- PRESS THE MUTE KEY (ON REMOTE CONTROL) ONCE, THE VOLUME WILL TURN
OFF AND THE MUTE SYMBOL WILL SHOW ON THE DISPLAY.
- TO RESUME THE SOUND, SIMPLY PRESS THE MUTE KEY AGAIN.
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER OR A TV TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE
THROUGH THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD STEREO
HEADPHONE (3.5MM TO 3.5MM PLUGS) CABLE TO CONNECT THE
"HEADPHONE-OUT OR AUDIO LINE-OUT" OF THE DEVICE TO THE AUX-INPUT SOCKET
OF THIS UNIT.
- SWITCH THE FUNCTION TO "AUX" USING THE KEY ON UNIT OR "AUX"
KEY ON REMOTE CONTROL.
- SWITCH ON THE UNIT AND THE EXTERNAL DEVICE (eg. MP3-PLAYER OR TV).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE UNIT WHEN YOU ARE FINISHED USING THE
EXTERNAL DEVICE.
FUNCTION
SPECIFICATIONS
POWER SUPPLY : ......................................... AC 120V ~ 60 Hz
POWER CONSUMPTION : ............................. 23W
SPEAKER : ..................................................... MAIN SPEAKER: 2.5" x 2
FREQUENCY : ............................................... FM 87.5 - 108 MHz
MYLAR SPEAKER: 1¼" x 2
THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND
NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE APPARATUS.
THE MARKING AND RATING LABEL IS LOCATED AT REAR ENCLOSURE OF
THE APPARATUS.
THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN
READILY OPERABLE. TO BE COMPLETELY DISCONNECTED THE POWER INPUT,
THE MAINS PLUG OF THE APPARATUS SHALL BE DISCONNECTED FROM
THE MAINS COMPLETELY. THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR
SHOULD BE EASILY ACCESSED DURING INTENDED USE.
UNDER THE INFLUENCE OF ELECTROSTATIC PHENOMENON,
THE PRODUCT MAY MALFUNCTION AND USER TO POWER RESET.
BATTERY SHALL NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE,
FIRE OR THE LIKE.
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
CAUTION
WALL MOUNT SET UP
- THIS UNIT CAN BE MOUNTED ON TO A WALL SURFACE.
- TYPE OF SCREWS USED FOR WALL-MOUNTING: 3.5 X 34MM BA (2 PCS)
IMPORTANT PRECAUTIONS
Not all types of walls are suitable or strong enough to support the weight of
this unit.
Please refer to a specialist to make sure that your wall is suitable, before wall
mounting. Drilling of holes must also be done by an experienced specialist,
to avoid injury and damage to your walls. Never place objects on top of the
speakers when they are wall mounted.
E-13 E-14
SYSTEM SET UP PROCEDURE
AS A "SHELF SYSTEM" (TABLE TOP USE)
- INCLUDED 1 PC STAND FOR THE MAIN UNIT.
FIXING THE BASE TO THE UNIT:
1. PLACE THE STAND UNDER
THE UNIT.
3. STOP WHEN THE INDICATOR MARK ON THE STAND IS ALIGNED WITH
THE LOCK SYMBOL ON THE REAR CABINET.
(TO RELEASE THE STAND FROM THE UNIT , SLIDE THE STAND DOWNWARDS
(OPPOSITE DIRECTION) UNTIL IT BECOMES RELEASED.
CLICK
2. SLIDE THE STAND UPWARD
(SEE DIAGRAM BELOW).
INDICATOR MARK
WHEN THE
INDICATOR MARK
ON THE STAND
LOCKED
IS ALIGNED
WITH THE LOCK
SYMBOL , THE
BASE IS
PROPERLY
IS PROPERLY
INSTALLED.
LOCK SYMBOL
E-15
DATE : 3 JAN 2011
MODEL : PICD65I “PYLE”
MANUAL PLAN FOR APPROVAL
E-8
E-7
E-6
E-5
E-9
E-10
E-11
E-12
E-4
E-3
E-2
COVER
E-13
E-14
E-15
BLANK
Loading...