Page 1
PDWM 5300
UHF PLL Diversity Wireless
UHF PLL Diversity Wireless
Microphone System w/ LCD
Microphone System w/ LCD
PDWM 5300
UHF PLL Diversity Wireless
UHF PLL Diversity Wireless
Microphone System w/ LCD
Microphone System w/ LCD
PDWM5300
OPERATION MANUALOPERATION MANUAL
PDWM5300
OPERATION MANUALOPERATION MANUAL
Page 2
Thank you for buying the PDWM5300 Wireless System. Please
read through these operation instructions so you will know how
to operate your model properly. After you read it, put it away in a
safe place for future reference.
Precautions
Hand-held microphone
Receiver
Installation
Trouble shooting
Specifications
Avoid exposure of the system to rain or moisture.
No user-serviceable parts inside the system. Refer all servicing to a qualified
technician only.
Handle the wireless system carefully, dropping or other shocks may cause
failure.
Avoid using the system where it may be subjected to heat, such as direct sunlight,
near radiators or other heat sources.
Should any liquid be spilt on the system, stop using it immediately. It may be
possible to dry the system, but you should have it checked by a qualified technician
before using it again.
Take care with the main power adapter and lead. If damaged in any way, do not use
the system and refer to a qualified technician for repair.
Only use the system with the supplied components. Do not attempt to use with any
other main power supply adapter .
wireless system
If the is not going to be used for a while, remove the battery to
prevent leakage. In the event of electrolyte leakage inside the battery compartment,
carefully remove the leakage with a damp cloth. Take care not to get battery
electrolyte in contact with your skin, however if it does, wash your hands under a
running tap. If electrolyte comes into contact with your eyes, seek medical advice
immediately.
Only replace the battery with the same or an equivalent type.
Please dispose of old batteries in an environmentally friendly manner in accordance
with the relevant legislation.
Do not use any solvents to clean any part of the .
wireless system
1
Page 3
6
+
-
+
-
DIP
ON
1234
FREQUENCY CHART
CH01
CH00
795.8MHz
795.2MHz
CH09
CH08
800.0MHz
800.6MHz
7
CH02
796.4MHz
CH10
801.2MHz
CH03
797.0MHz
CH11
801.8MHz
CH04
797.6MHz
CH12
802.4MHz
ON
OFF
CH05
798.2MHz
CH13
803.0MHz
CH06
798.8MHz
CH14
803.6MHz
CH07
799.4MHz
CH15
804.2MHz
PARTS DESCRIPTION
1. Mesh: cartridge inside
2. Tube
3. Power LED indicator
4. Power and Mute switch: Switch on and off the microphone.
Move the switch to middle position to mute the mic.
5. Battery compartment
6. Battery Cover
7. CH selector
OPERATION
1. Unscrew the battery cover at the end of the microphone. Install the
provided 2 1.5V batteries, taking care to fit it with the correct polarity
connected.
2. According to frequency Chart on the battery cover, adjust the CH
selector to make the microphone to be the same frequency as receiver.
3. Check the battery by switching the microphone ON. The red LED will
come on. This indicates correct operation. If the red LED is dim, this
indicates the battery is low and should be changed. If the red LED does
not come on at all, it indicates the battery is dead and should be replaced.
2
Page 4
CH00 795.2MHz
00dB AF
PARTS DESCRIPTION
1. Power Switch: Turn on power switch, the display of LCD will illuminate.
2. Power LED indicator: Turn on power switch, this indicator will illuminate.
3. SET: Press once to adjust frequency by UP/DOWN buttons. Press again to exit.
4. UP: Channel UP
5. DOWN: Channel DOWN
6. LCD Display
7. Volume control
8. Antenna A and B
9. Balanced output
10. Unbalanced output
11. 12V DC IN
OPERATION
Connect the antennas A and B. Make sure they are vertical.
1.
2. Insert one end of included audio cable into AF OUT on rear panel,
and the other end into LINE IN of amplifier or mixer.
""
""
3. Connect the power adaptor from DC 12V of receiver to a main power socket.
4. Switch on the receiver. The power indicator comes on. LCD display will
Press
illuminate.
Now you can adjust frequency by UP/DOWN buttons. Press SET again to
SET once, there will be a mark displayed on LCD panel.
exit.
Make sure the microphone and receiver to be of same frequency.
5. Switch on the microphone.
A letter "A" or "B" will appear in the top right of the
LCD, indicating the diversity reception. RF strength (in dB) is indicated in the
bottom left corner of the display. hen you speak into the microphone, AF
signal will
display on the bottom of LCD display panel.
W
3
Page 5
Using the supplied audio cable, connect from the AF OUT jack socket to the
LINE IN socket on amplifier.
the XLR balanced output.
Alternatively, you can connect an XLR cable to
Connect the mains power adaptor from "DC 12V"
jack to a suitable mains power socket.
Installation Location:
At least 3 ft. above ground level
At Least 3 ft. away from wall
MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE
4
Page 6
The on air
indicator does
not light up
No sound
The sound is
distorted
A howling noise
heard from the
speakers.
The wireless microphone is not
turned on.
The microphone receiver is not
turned on.
The microphone receiver is not
connected properly.
Frequency not set correctly.
The battery in the wireless
microphone is weak.
The microphone receiver is not
turned on .
The connected audio equipment is
not turned on.
The speakers/headphones. are not
connected to the audio equipment.
The battery in the wireless
microphone is weak.
The AUDIO OUT on the receiver
is not set correctly.
The distance between the wireless
microphone and speakers are too
close.
The battery in the wireless
microphone is weak
Turn on the wireless microphone
Turn on the microphone receiver
and the connected audio equipment
Turn on the microphone receiver
and the connected audio equipment
Make sure mic and receiver are
set to the same frequency.
Replace the battery.
Turn on the microphone receiver
and the connected audio equipment.
Turn on the audio equipment.
Connect the speakers/
headphones
Replace the battery.
Adjust the volume controls.
Move the wireless microphone
away from the speakers or
change the direction of the
microphone.
Replace the battery.
5
Page 7
A. Overall System
arrier Frequency: UHF 795~805MHz
C
Frequency Stabilization: less than 30ppm
Dynamic Range: more than 90dB
Total Harmonic Distortion: less than 0.5%
Frequency Response: 40hz~15khz 3dB
Audio Output Level: separate type:0~ 400mV
Mix Type: 0~ 200mV
B. Receiver
Power Supply: DC 12V
Consume Power: 4W
Signal/Noise Ratio: more than 90dB
Image & Spurious Rejection: more than 80dB
Border upon Channel Rejection: more than 80dB
Receiving Sensitivity: 10dBuv(sinad=30dB)
De-emphasis: 50us
C. Transmitter
ansmitting Power: 8.5mW
Tr
Modulation Type : FM,F3F
Max Deviation: 25KHz
Spurious Emission: more than 40dB(with carrier)
Power Supply: 3V
6
Loading...