PYLE Audio FCN200 User Manual

FLOORING CLEAT
NAILER

Instruction

manual

The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.

Part No. 899223 (015)

ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 25

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Copyright © 2001 Porter-Cable Corporation

MODEL FCN200

Patent No: 6,155,472

899223 - 05-31-01.qxd 2/19/02 2:00 PM Page 1

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using pneumatic tools, basic safety precautions

should always be followed to reduce the risk of personal injury, including
the following:

READ AND FOLLOW ALL INSTRUCTIONS.

There are certain applications for which this tool was designed. Porter-Cable
strongly recommends that this tool NOT be modified and/or used for any
application other than for which it was designed. If you have any questions
relative to its application DO NOT use the tool until you have written Porter­Cable and we have advised you.

Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305

1. USE SAFETY GLASSES. To prevent eye
injuries, the tool operator and all persons in
the work area must wear safety glasses with
permanently attached, rigid, plastic side
shields. These safety glasses must conform to
ANSI Z87.1 requirements (approved glasses
have “Z87” printed or stamped on them).
Fig. 1.

2. WEAR EAR PROTECTION to safe­guard against possible hearing loss. Fig. 1.

3. OPERATOR AND BYSTANDERS WEAR
HARD HAT to safeguard against possible

injuries. Fig. 1.

4. USE CLEAN, DRY, REGULATED com­pressed air at 70 to 100 PSI, (4.8 to 6.9
BAR). Fig. 2.

5. DO NOT CONNECT TOOL TO pressure
which potentially exceeds 200 PSI (13.8
BAR).

6. ONLY USE AIR HOSE THAT IS RATED

for a maximum working pressure of at least
150 PSI or 150% of the maximum system
pressure, which ever is greater.

7. NEVER USE OXYGEN, CARBON
DIOXIDE, combustible gases or any other

bottled gas as a power source for this tool:
explosion and serious personal injury could
result. Fig. 3.

8. CONNECT TOOL TO AIR SUPPLY
HOSE with a coupling that removes all

pressure from the tool when the coupling is
disconnected. Fig. 4.

2

Fig. 1

Fig. 2

Fig. 3

Fig. 4

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 2

3

9. DISCONNECT TOOL FROM AIR
SUPPLY HOSE before doing tool

maintenance, clearing a jammed fastener,
leaving work area, moving tool to another
location, handing the tool to another
person, or making adjustments. Fig. 5.

10. NEVER USE A TOOL that is leaking
air, has missing or damaged parts, or
requires repair. Make sure all screws and
caps are securely tightened.

11. NEVER USE TOOL IF TRIGGER

mechanism is inoperable, missing or
damaged. Do not alter or remove trigger
mechanism. Make daily inspections for free
movement of trigger mechanism.

12. DO NOT USE TOOL WITHOUT
SAFETY WARNING LABEL. If label is

missing, damaged or unreadable, contact
your Porter-Cable Service Center for a
replacement. Fig. 6.

13. ONLY USE PARTS, FASTENERS,
AND ACCESSORIES recommended by

Porter-Cable.

14. REMOVE ALL FASTENERS from tool
before connecting to air supply. The tool’s
driving mechanism may cycle when tool is
connected to the air supply. Fig. 7.

15. ALWAYS ASSUME THE TOOL
CONTAINS FASTENERS. Keep the tool

pointed away from yourself and others at all
times. No horseplay. Respect the tool as a
working implement. Fig. 8.

16. DO NOT LOAD FASTENERS with
trigger depressed, to prevent unintentional
firing of a fastener. Fig. 9.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

1

2

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 3

4

17. REMOVE FINGER FROM TRIGGER

when not driving fasteners. Never carry tool
with finger on trigger: tool will fire a fastener
if rubber cap is bumped while trigger is
depressed. Fig. 10.

18. USE THE MALLET TO RACK THE
WOOD STRIP, NOT THE NAILER. Fig. 11.

19. DO NOT USE THE METAL END OF
THE MALLET TO STRIKE THE PLUNGER,

use the rubber capped end only.

20. FIRE FASTENERS INTO WORK
SURFACE ONLY: never into materials too

hard to penetrate.

21. DO NOT USE THE NAILER TO
POSITION the flooring strips. Hitting the

rubber cap without first activating the trigger
will cause severe internal damage to the
Nailer. Fig.12.

22. THE TRIGGER IS A SAFETY DEVICE

and should only be pulled when the Nailer is
in proper position on the work surface and
before the rubber cap is struck with the
mallet. Do not tie or tape down the safety
trigger as the Nailer could discharge if
dropped on the rubber cap. The Nailer will
not fire unless the trigger is pulled before the
mallet blow. Fig.13.

23. DO NOT DRIVE FASTENERS on top of
other fasteners: the fasteners can ricochet
causing personal injury.

Fig. 10

Fig. 11

Fig. 12

Fig. 13

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 4

5

EMPLOYER’S RESPONSIBILITIES

WARNING: Employer must enforce compliance with the safety warnings

and all other instructions contained in this manual.

Keep this manual available for use by all people assigned to use this tool.

For personal safety and proper operation of this tool, read and follow all of
these instructions carefully.

OPERATING INSTRUCTIONS

FOREWORD

Porter-Cable Model FCN200 is a heavy duty, pneumatic flooring cleat nailer.
It is designed to install tongue and groove hardwood flooring with L-shaped
flooring cleats. Flooring in thicknesses of

1

/2" and 25/32" can be installed using

1-

1

/2" and 2" length flooring cleats respectively. See ACCESSORIES Listing in

back of this manual.

CAUTION: Use approved Porter-Cable flooring cleats only. Porter-Cable
flooring cleats are made with special design features with superior holding
strength. See ACCESSORIES Listing in back of this manual.

POWER SOURCE

This tool is designed to operate on clean, dry, compressed air at regulated
pressures between 70 and 100 PSI (Pounds per Square Inch)( 4.8 to 6.9 Bar).
The preferred system would include a filter, a pressure regulator, and an
automatic oiler located as close to the tool as possible (within 15 feet is ideal).

All compressed air contains moisture and other contaminates that are
detrimental to internal components of the tool. An air line filter will remove
most of these contaminates and significantly prolong the life of the tool. If an
in-line oiler is not available: place 10 to 15 drops of Porter-Cable Air Tool Oil
(see ACCESSORIES), into the tool’s air inlet at the beginning of each workday.

IMPORTANT: Do not over lubricate the Nailer, excess oil mist or drops
will be vented with spent air when over lubricated. Excess oil could stain
the wood flooring, walls or furnishings. Dry fire the Nailer, without nails, to
purge excess oil, before you begin nailing.

The tool is equipped with a

1

/

4

" male “quick connector”. A

3

/

8

" male “quick
connector” is available from Porter-Cable and may be used in situations where
a

1

/

4

" supply line is not available. The tool must always be connected to the air
supply with a coupling such that all pressure is removed from the tool when the
coupling is disconnected.

WARNING:

All air line components (hoses, connectors, filters, regulators,
etc.) must have a minimum working pressure rating of at least150 PSI (10.3
BAR) or 150% of maximum system potential, whichever is higher.

Do not connect this tool to a system with maximum potential pressure
greater than 200 PSI, (13.8 BAR).

Only connect tool to air supply with a coupling that will release all
pressure from the tool when disconnected.

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 5

Disconnect tool from air supply before performing maintenance,
clearing a jammed fastener, leaving work area, moving tool to
another location, handing the tool to another person, or making
adjustments.

PREPARING THE TOOL

1. After reading and understanding this entire manual, connect tool to air
supply (see Fig. 15).

WARNING: Keep tool pointed away from yourself and others at all
times.

Always connect tool to air supply before loading fasteners. Do not
load fasteners with trigger depressed.

Use only approved Porter-Cable fasteners (see ACCESSORIES).
Always wear Z87.1 approved safety glasses, and hearing protection

when preparing or operating the tool.
Never use a tool that leaks air or needs repair.

2. Orient a strip of L-shaped cleats with points down (see Fig. 16), and align
with the slot (L) at the end of the magazine.

3. Feed the strip of cleats into the magazine

4. Pull the follower (B) Fig. 17, all the way to the rear of the magazine and
release. The follower will apply pressure to the strip of cleats to feed it into
the driving mechanism.

6

Fig. 15

Fig. 16

“L”

Fig. 17

B

Fig. 18

B

C

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 6

7

USING THE TOOL

Complete all steps of PREPARING THE TOOL before using the tool.

First position and closely fit together (rack) the flooring strip with the (metal)
mallet. Position the tool on the tongued edge of the flooring strip (see Fig. 18)
aligning the driver guide against the front of the flooring strip. Pull and hold
the trigger and strike the rubber cap with the rubber mallet. The tool will then
drive the cleat at the correct 45 degree angle as shown in Fig. 19 and 20. The
proper length of flooring cleat to use with various thicknesses of flooring is
also shown in Fig. 19 and 20.

It is not necessary to hit the rubber cap hard to activate it. Never hit the tool
hard with excessive force, as this will damage the tool.

DO NOT USE THE NAILER TO POSITION the flooring strips. Hitting the
rubber cap without first activating the trigger will cause severe internal
damage to the Nailer.

DO NOT USE THE METAL END OF THE MALLET TO STRIKE THE RUBBER
CAP, use the rubber end only.

WARNING: The trigger is a safety device and should only be pulled
when the tool is in the proper position on the work surface and
before the rubber cap is struck with the mallet. Do not tie or tape
down the safety trigger as the tool could discharge if dropped on the
rubber cap. The tool will not fire unless the safety trigger is pulled
before the mallet blow.

NOTE: When Using Tool to install Pre-finished Flooring

The Porter-Cable FCN200 was designed for installing both
unfinished and pre-finished hardwood flooring. Care must be used
however when installing pre-finished flooring to ensure that the finish
is not damaged by the tool. It is recommended that the tool be
inspected for damage [especially the base plate (C) Fig.18] and
tested on a sample section to be certain that the tool and technique
of use do not mar the finish. This procedure should be followed
before each job due to variations in flooring and tool condition.

WARNING: Remove finger from trigger when not driving fasteners.
Never carry tool with finger on trigger: tool will fire a fastener if
rubber cap is bumped.

WARNING: Keep tool pointed in a safe direction at all times.

Fig. 19

Fig.20

899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 7

8

WARNING: Never attempt to drive a fastener into material that is

too hard. The fastener can ricochet causing personal injury.
WARNING: Disconnect tool from air supply before performing

maintenance, clearing a jammed fastener, leaving work area, moving
tool to another location, handing the tool to another person, making
adjustments.

WARNING: Clean and inspect tool daily. Carefully check for proper
operation of trigger mechanism. Do Not use the tool unless the
trigger mechanism is functional. Do Not use if the tool is leaking air
or needs any other repair.

CLEARING A JAMMED FASTENER

1. CAUTION: Disconnect tool from air supply.

2. Remove any remaining fasteners from the nailer.
A. Pull pusher back by pulling front knob (A) Fig. 21. This will retract the

pusher face from the cleat strip.

B. Still using the front knob (A) Fig. 22, slide the pusher to the front

bypassing the cleat strip.

C. Slide the remaining Fasteners out of the magazine. Fig. 23.

3. Use the 3/16” hex wrench to remove the three screws (A) Fig. 24
attaching the Driver Guide Plate and Gate (B) Fig. 24.

4. Slide out the Driver Guide Plate and Gate assembly. Fig. 25.

5. Pull the Driver Guide Plate and Gate assembly apart and remove the

jammed Fastener. Fig. 26.

6. Replace the Driver Guide Plate and Gate with three screws.

Fig. 21

A

Fig. 23

Fig. 24

A

Fig. 22

A

B

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 8

9

MAINTENANCE

CLEAN AND INSPECT DAILY

CAUTION: Disconnect tool from air supply before cleaning and

inspection. Correct all problems before placing the tool back in use.

Wipe tool clean and inspect for wear or damage. Use non-flammable
cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK
tool with cleaning solutions. Such solutions can damage internal parts.

Inspect trigger mechanism to insure system is complete and functional: no
loose or missing parts, no binding or sticking parts.

Keep all screws tight. Loose screws can cause personal injury or damage
tool.

If tool is used without an in-line oiler: place 10 to 15 drops of Porter-Cable
Air Tool Oil into the air inlet of the tool at the beginning of each workday.

IMPORTANT: Do not over lubricate the Nailer, excess oil mist or drops
will be vented with spent air when over lubricated. Excess oil could stain
the wood flooring, walls or furnishings. Dry fire the Nailer, without nails, to
purge excess oil, before you begin nailing.

SERVICE AND REPAIRS

All quality tools eventually require servicing or replacement of parts due to
wear from normal use. Some user serviceable components are described in
the TROUBLESHOOTING Section. Complete product Service is available
from either an AUTHORIZED PORTER-CABLE SERVICE STATION or a
PORTER-CABLE/DELTA FACTORY SERVICE CENTER. All repairs made by
these agencies are fully guaranteed against defective material and
workmanship. We cannot guarantee repairs made or attempted by anyone
other than these agencies.

Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).

Fig. 25

Fig. 26

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 9

10

TROUBLESHOOTING

CAUTION: Disconnect tool from air supply before performing any

Service Procedure.

SYMPTOM PROBLEMS SOLUTIONS

1. Air leak near top of Loose screws. Tighten screws.

tool or in trigger area. Worn or damaged Install “OVERHAUL” Maintenance Kit.

o-rings or seals.

2. Tool does nothing or Inadequate air supply. Verify adequate air supply.

operates sluggishly. Inadequate lubrication. Put 10 to 15 drops of oil into air inlet.

Worn or damaged Install “DRIVER” Maintenance Kit.
o-rings or seals. Install “OVERHAUL” Maintenance Kit.

3. Air leak near bottom Loose screws. Tighten screws.

of tool. Worn or damaged Install “OVERHAUL” Maintenance Kit.

o-rings or bumper.

4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of

correct size.
Damaged fasteners. Replace w/undamaged fasteners.
Magazine or nose Tighten screws.
screws loose.
Magazine is dirty. Clean magazine.
Pusher spring damaged. Replace spring.
Driver is worn or damaged. Install “DRIVER” Maintenance Kit.

5. Other. Contact a Porter-Cable
Service Facility.

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 10

11

ACCESSORIES

A complete line of accessories is available from your Porter-Cable ·
Delta Supplier, Porter-Cable · Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site

www.porter-cable.com for a catalog or for the name of your nearest

supplier.

WARNING: Since accessories, other than those offered by Porter-Cable

· Delta, have not been tested with this product, use of such accessories

could be hazardous. For

safest operation

, only Porter-Cable ·Delta

recommended accessories should be used with this product.

CATALOG NO. DESCRIPTION LENGTH QUAN/BOX

FLC150 Flooring Cleat Nails 1-

1

/2" 1000

FLC200 Flooring Cleat Nails 2" 1000

60076 Overhaul Kit
60077 Driver Kit

48248 Wrench Allen 3/16”

48245 Wrench Allen 5/32”
884293 Oil (for Air Tools)
899226 Mallet

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 11

12

PORTER-CABLE LIMITED ONE YEAR WARRANTY

Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof
of purchase may be required. This warranty does not apply to o-rings and driver blades or to repair or
replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by
other than our Service Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF
PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825
Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND
UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 12

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE •DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA): BAMMER®, LASERLOC®, OMNIJIG®, POCKET

CUTTER

®

, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®, SPEEDMATIC®,

SPEEDTRONIC

®

, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®, TORQ-BUSTER®,

VERSA-PLANE

®

, WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™, JETSTREAM™, MICRO-SET™,

MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países. Marques déposées, indiquées par la lettre ®, sont déposées au Bureau des brevets d’invention et marques
déposées aux Etats-Unis et pourraient être déposées aux autres pays.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

(CENTRE DE SERVICE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable •Delta Power Tools are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one. Parts
and accessories for Porter-Cable

•

Delta products should be obtained by contacting any Porter-Cable •Delta Distributor, Authorized

Service Center, or Porter-Cable

•

Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will

be directed to the nearest Porter-Cable

•

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en

muchas grandes ciudades. Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los
accesorios para los productos Porter-Cable

•

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable

•

Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable •Delta. Si no tiene acceso a ninguna de estas
opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

•

Delta más cercano. Des centres de service

agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en
repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable

•

Delta, s’adresser à tout distributeur Porter-Cable

•

Delta, centre de service agréé ou centre de service d’usine Porter-Cable •Delta. Si vous n’avez accès à aucun de ces centres, appeler le

888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable

•

Delta le plus proche.

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]

Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
311 Laura Drive
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Braintree 02185 (Boston)
719 Granite Street
Phone: [phone]
Fax: [phone]

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
4315 68th Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.

Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: [phone]
Fax: [phone]

WASHINGTON

Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: [phone]
Fax: [phone]

Printed in U.S.A.

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 Ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: [phone]
Fax: [phone]

899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 36