PYLE Audio AT-3040 User Manual

INSTALLATION

PRECAUTIONS

1. Choose the mounting location carefully so that the unit will not interfere with the
normal driving functions of the driver.

2. Avoid installing the unit where it would be subject to high temperatures, such as
from direct sunlight or hot air from the heater, or where it would be subject to
damp, dust, dirt or excessive vibration.

3. Use only the supplied mounting hardware for a safe and secure installation.

DASH BOARD

AT-3040

HEX NUT

SPRING WASHER

PLAIN WASHER

TAPPING SCREW

METAL MOUNTING STRAP

CONSOLE

SLIDE BRACKET HOUSING

HEX BOLT

KEY PLATE

To remove the player from the Cage, insert the supplied key
into the slot of the chassis then pull the chassis out of the
cage as shown.

SPECIFICATION

GENERAL
Power Supply Requirements DC 12Volts. Negative Ground.
Unit Dimensions 178[W]X150[D]X50[H] mm.

FM SECTION
Frequency Range 88MHz - 108MHz.

AM SECTION
Frequency Range 530KHz - 1700KHz.

INSTRUCTION MANUAL

H

PWR

BD

VOL

LOC

M

F/C

ST

BAL

TONE

MHzFM

THEFT DETERRENT DETACHABLE SYSTEM
AUTO-STOP CAR CASSETTE PLAYER
AM/FM 2 BAND LCD DISPLAY TUNING RADIO

www.pyleaudio.com

AUTO STOP

CD IN

TUNE

REL

LOCATION AND FUNCTION OF CONTROLS

11

1

4

2

3

9. Local/Distance Reception Button
This operation is effective on FM reception only.

6

16

In RADIO mode, press this button to change between local and distant reception.
Press LOC to improve local reception in some areas where the signal is too strong.
Press LOC to improve distant reception when you are located at a weak signal location.

H

PWR

BD

VOL

LOC

M

5

12

F/C

ST

BAL

TONE

13

8 109

14

MHzFM

7

AUTO STOP

CD IN

15

TUNE

REL

1. POWER ON/OFF BUTTON

Press this button to turn the power supply on or off.

2. VOLUME CONTROL

Slide this control up or down to increase or decrease the volume level.

3. CASSETTE TAPE DOOR

In RADIO mode, insert a cassette into this slot, the tape playback starts automatically.

4. EJECT KEY

In TAPE mode, push this key half way to fast forward, and fully to stop tape playback
and release cassette tape. The car radio cassette player will automatically go into
radio mode.

5. BAND SELECTOR BUTTON

Each press for AM / FM reception. The character of band which has been selected
will be visible on the display indicating the status of tuning.

6. TUNING CONTROL

Rotate this control at radio mode to select your desired radio broadcasting station
within AM/FM. While the frequency appears on the display.

7. LCD DISPLAY

8. MO/ST BUTTON

This operation is effective on FM reception only.
In RADIO mode, press this button to change between mono or stereo sound effect.
The ST will appear on the display while there is a strong signal from an FM station
that is broadcasting in stereo. Mono improves the reception of the distant stereo FM
stations.

10,11& 12. CLOCK DISPLAY AND SETTING BUTTON

Press F/C at radio or tape mode for frequency or clock display.
Time setting:
With time appeared on the LCD display, press and hold F/C button, then press the
H and M button at the same time to adjust hour and minute.

13. BALANCE CONTROL

Rotate this knob to adjust the audio output balance of left and right speaker.

14. TONE CONTROL
Rotate this knob to adjust the TONE sound effect.

15. EXTERNAL CD INPUT JACK

This car radio cassette player can be connected to a portable CD player through this
jack.

16. RELEASE BUTTON

Press this button to eject the detachable front face panel from the chassis.

WIRING DIAGRAM

ANTENNA JACK

RED

R.

RCA LINE OUT

L.

WHITE

WHITE

LEFT
SPEAKER

+

L.

-

BLACK GROUND

NOTE:
Speakers with load impedance less than 4 ohms could damage the equipment.
Make sure use a speaker with 4 ohms load impedances to reduce the distortion
during high volume level.

BLUE AUTO ANTENNA

3A

B+ POWER

0.5A
YELLOW

B+ MEMORY

GRAY

+

R.

-

RED

RIGHT
SPEAKER