PLTK300
OWNER,S MANUAL
TV TUNER SYSTEM
Precautions 3
System features and controls 4
Installation and electrical connections 5
Remote Function 7
Selecting the input mode 7
Programming channels for TV 7
Selecting channels and adjusting the sound 8
Providing A/V audio to your car radio 8
Specifications 10
Transmitting audio to your car radio 9
Changing the remote battery 10
We verythank for yourpurchase.
Please readthis user,s Manualin detail anduse the setproperly.
CONTENTS
2
R
Installation and Electrical Connections
1.Find a suitable location for the tuner unit and mount it securely
in place. Be sure to place it in an area away from moisture and
dirt, and where incoming cables will not be walked on or pulled
accidentally.
2. Make all required audio, video and power connections to the
appropriate connectors on the tuner as indicated in the drawing
below to suit you system installation. Install the infrared remote
eye in a located you know will be available in line-of-sight with
the remote control use location.
Please note that the drawing below describes connections
for all system possibilities and your particular system may
vary from this.
5
Precautions
1.Do not operate this equipment while-safe driving should always be your highest priority.
2.Do not install these components in an area which are susceptible to rain, moisture, direct sunlight, extreme
heat or cold, excessive dust, dirt or humidity.
3.Immediately unplug the power cord and send the monitor to your local dealer or service center as soon as
possible:
a) If there is smoke or any peculiar odor present during use.
b) If there is damage to any of the component casings.
4.To avoid damage and risk of electronic shock, do not permit this equipment to become damp or wet from
water or drinks. If this dose occur, immediately unplug the power cord and send the unit to your local dealer
or service center as soon as possible.
5.Do not attempt to repair, open or diassemble any of the components. Dangerous high voltages are present
which may result in electric shock.
6.Use only a power source with 12 Volts DC (negative ground).
7.Do not place objects on or suspend objects from the power cord, as this may damage the cord.
8.Do not twist or place the power cord near any source of heat in the vehicle.
9.Do not attempt to repair a damaged, broken or faulty power cord. Replace it with a new one immediately.
Please read this manual completely and carefully prior to attempting to install the equipment.
3
8
POWER
MUTE
VOL+
VOL-
CH+
CH-
MENU
AVC
AUTO
TVTUNER
REMOTE
Selecting channels and adjusting the sound
Use the CH+ and CH- buttons for selecting channels.
Use the VOL+ and VOL- buttons to increase or decrease audio volume.
You will see a Volume Bar on screen indicating relative volume level.
Pressing the MUTE button will disable the audio output. To cancel the
muting function, press MUTE again.
Please note :VOL+, VOL- and MUTE buttons are of no effect inAV
mode.
Providing A/V audio to your car radio
This system offers you two ways of playing the A/V audio through your car radio
system. If your radio has AUX line-level inputs, you can attach the A/V audio output
connectors to these inputs with RCA-RCA interconnect cables.
If your car radio lacks these AUX line level input, your other option is to use the tuner
audio transmission ability to broadcast the audio signal within your car directly to
the radio FM modulation.
10
Specifications
Changing the battery in the remote
1.The remote battery is held in a small drawer on one edge
of the remote.To open this drawer, press and hold the small
button on the edge of this drawer(as show below) and slide
the drawer out
2. Insert a new battery and push the drawer back fully into the
remote.
NTSC
Audio R/L 2, Video 2
Audio R/L 1, Video 1
4 ChannelFM(87.7/87.9/88.1/88.3MHz)
Channels 2-81
L)7 (W)4.5 (H)1.1inch
0.47Kg
Signal System
Audio/Video Inputs
Audio/Video Outputs
FM transmitter
TV Channel
Tuner Box, Overall Dimensions
Tuner Box, Weight
Release button
Battery
+
Loading...