Outp ut p ower, 2 channels dri ve n
4-oh m, 1 K Hz 1% TH D. 28. 5 Wx2
4-oh m, 1 K Hz 10% THD. 22 .5 Wx2
Peak P ow er 4 0 Wx2
www.PyleAudio.com
MINI 2X40W STEREO POWER AMPLIFIER
W/BLUETOOTH& W/USB CHARGING
FOR MOBILE PHONE
MODEL:PTA22BT
7.48x.2.8 x5.31inch(WxHxD)7
USER MANUAL
FOREWORD
FEATURES AND CONTORLS
FRONT PANEL
1
2 3 4 5
6 7
1. POW ER On LED Indicator
-Lig hts to indicate pow er is turn on or off.
2. USB Charge Port
-
USB port charges for smartphone, not for USB reader
function.
3. BLUETOOTH Indicator
When switches to Bluetooth mode, the indicator light will
-
be on.
When plays by Bluetooth mode, the light will flash.
-
Bluetooth/Line input switch
4.
-
Mode button switches between the
audio inputs.
Push in is for Bluetooth function, and push out is for Line
-
!
audi o input.
5. 1/8" AUX/CD IN
-Let s you easily connect the computerized MP3 Device
(player) sources, such as PC( CD ROM),laptop, walkman,
iPod,and cell phone.
6. Main Power on Switch
The
amplifier is switched ON or OFF by using this switch.
-
8 9 10 11 12
Bluetooth and Line
7. 1/4" PH ONE JACK
Accepts headphones with 1/4" plug
-
!
BACK PANEL
13 14 15
14.
Bluetooth Antenna
-
Use of antenna is best receiving for Bluetooth signal.
15.Fuse
-
The amplifier uses a fuse for protection against surges
and short circuit. If the amplifier suddenly turn off and
will not turn on, check the fuse. If necessary, replace
it with a 1-amp, 250-volt, fast- acting, 5x20mm fuse
(not supplied)
16.
1/4" MIC INPUT JACK
-Lets you connect a microphone with a 1/4" p lug.
16 17 19 20 2118
8. MIC VOLUME CONTROL
-Lets you adjust the volum e of connected MIC to the proper
setting.
9.Master Volume Control
-Lets you adjust the overall sound level,turn the knob
clockwise to increase the volume.
10.BALANCE CONTROL
-let s you adjust the sound balance b etween the le ft and right
ampl ifier output.
11.BASS AND TREBLE TONE CONTROL
-Let s you boost or attenuate bass an d treble for the desired
soun d.
12.AUX1/AUX2/CD INPUT SELECTOR
-Let s you select the desired input m usic source .
13.SWITCHABLE MIC PAGER AND MIXING MODES
-Set t o PAGER , allows a voice to be heard clear ly through the
micr ophone by attenuating auto matically a ll the audio input
sour ce.This is good to use when pagi ng the person i n offi ce,
stor e, or restaurant.
-Set t o MIXING, both of the voices fro m the microphone and
musi c will be existed at the same time . It is similar like playing
at KAR AOKE events.
17.AUX1/AUX2/CD RCA INPUT
-Lets you connect to most high-level audio sources such as CD
player, tape deck, tuner, camcorder or VCR .
18.REC RCA OUTPUT
-Lets you connect the amplifier to a tape deck for recording.
19.
Push Type Speaker L/ R Terminals
-
Let you easily connect the speakers'wires directly to
the amplifier
20.110V/220V Switch
-
According to power voltage, push this button to the
correct station of the 110V or 220V.
21.
AC IN Power Cord
-Connect to AC 11 0V/60Hz or 220V/50Hz
BLUETOOTH FUNCTION INSTRUCTION
External devices w hich have a built‐in Bluetooth feature can be
connected to this amplifier wirelessly to play through the
amplifier’s speakers.
1. Be sure that the amplifier is powered on. And it’s better to pull
the Bluetooth Antenna on at the back of pan el for better
receiving. Press MODE button on the front panel in like
situation, and the Bluetooth Indicator is light on. (The unit is
automatically re ady to pair with your devic e)
2. Turn on the Bluetooth function of your external device.
3. Search for available devices within range of your external
Bluetooth device.
4. Wait for a while then find the “TD301-RY” on the paired
devices list on your external device and sele ct “TD301-RY”,
or find the “BT” on the paired devices list on your ext ernal
device and select “BT”.
5. Your amplifi er will beep and the lights will flash once when
pairing is a success.
6. You can now play music and other audio on your external
device through you r amplifier.
7. The amplifier will beep and the lights will flash once again
when the external de vice is turned off or unpaire d.
Sound source or speakers
may not be connected
properly.
Master volume control may
be set to a minimum.
The amplifier is shutting down
or powering off
Feedback Reposition the microphone and
Microphone and speakers are
to close together
Adjust the volume control to
a higher setting.
Make sure that the speakers
that you have connected to
the amp are matching in
impedance.
Turn the amplifier off and let it
cool, make sure that the amplifier
is properly ventilated, and then
turn it back on.
speakers
Loading...