Pyle PSWLE81 Installation Manual

TV Size Range: 26 42

Maximum Weight Capacity: 25kg/55lbs

VESA: 400X400

Safety automatic lock

Unlock cord

"～ "

CAUTION

-8-

This product containssmall items thatcould be achoking hazard if swallowed. Keep
these itemsaway from young children

1.Make sure these instructions are read andcompletely understood before attempting
installation. Ifyou are unsure of any partof this installation,contact a professional
installer forassistance.

2.The wallor mounting surfacemust be capableof supporting thecombined weight of
the mountand the display; otherwise the structure must be reinforced

3.Safety gearand proper tools must be used. A minimumof two peopleare required
for thisinstallation. Failure to use safety gear can result inproperty damage, serious
injury or death.

!

.

Warning

This product wasdesigned to beinstalled on woodstud walls andsolid concrete walls.
Before installing make sure the supporting surface will support thecombined load ofthe
equipment andhardware. Never exceed the Maximum Load Capacity.This product is
intended forindoor use only. Use of this product outdoorscould lead toproduct failure or
personal injury.The depth of this mount(1.3 ) maynot provide sufficient space for proper
ventilation onsome screens. Please refer to themanufacturer ’s requirements for mounting
your screen befourinstallation.

"

Wrench 4x4

±180°

±180°

±180°

Part 5-Adjusting display and using cord management

Route cords along articulating arms using cord management s.
Articulating arms can be adjusted to position display into desired location.
Use wrench(8) to tighten and loosen the tension screw. Do not overtighten
or overloosen to make the screws come out.

clip

Part 5-Adjusting display and using cord management

-5 15°~ °

±5°

Thank you for choosing our productThank you for choosing our product

Item No.:

PSWLE81

Item No.:

PSWLE81

INSTALLATION GUIDE

www pyleaudio com..

Pyle Audio
1600 63rd st , Brooklyn,NY,11204
[phone]

-2-

Hardware Kit:

Hardware Kit:

-7-

1

2

3

4

Part 4-Mounting the flat panel screen

NOTE:

Hook the top of brackets onto the top flange of wall plate(1). Then
swing the screen down. Fixed slide block into wall plate by screw.

(2)

Always use an assistant or mechanical lifting equipment to safely lift

and position heavy equipment.

Part 4-Mounting the flat panel screen

NOTE:

5

Magnetic removable
bubble level

A-D

H

E

G

F

6

7

6

7

2

8

ID Description

1
2

6

3

B

1
2

2

4

Screw

M5 mm×16 bolt

Qty

Description

Square washer

Long bolt
Wallanchor

Long bolt washer

M8×16mm bolt

M6× mm16 bolt

4

2

ID

Qty

3
3

F
G

H

3

D

4
4

E

C

4

Ribbon

Wallplate
Bracket

5

1

TV plate

2

Plastic cover

7

2

Slide block(Position lock)

A

4

M4 mm×16 bolt

8

1

Wrench(4x4)

Before installation, please attach these two decorative end caps to the two
sides of TV plate.(FIG.A)

FIG.A

-3-

Wood stud

Part 1a-Wood Stud Mounting

.

Usewallplate(1)asatemplate,makesureitislevel,andmark
mounting holes on the wood studs. Drill 3/16

)

)..

three

three (4.5mm)dia holes 50
mm deep. Level wall plate(1) and attach to wall with three long bolts(G and
three washers(F . Tighten screws firmly Do not overtighten

”

Part 1a-Wood Stud Mounting

Stud finder

50mm

Φ3/16 (4.5mm)”

-6-

.

Part 3-Attaching brackets to screen

Center brackets vertically on back of screen. Select the

Attach brackets to screen using four selected

screws and four square washers(E) at the top and bottom of each bracket.

small(A),medium

(B or C) or large(D) screws.

Tighten screws firmly. Do not overtighten

Part 3-Attaching brackets to screen

A-D

E

Square washer(E)

Small holefor
M4 screws

Medium holefor
M5andM6screws

Large hole for
M8 screws

Magnetic removable
bubble level

G

F

5

Part 2-Attaching plastic covers to wall plate

Secure plastic covers over wall plate by pushing them toward each other
until they lock in place.

Part 2-Attaching plastic covers to wall plate

-4-

-5-

Part 1b-Concrete Wall Mounting

.

Level wall plate and use wall as a template to mark three holes. Drill three
7/16 (10.5mm) dia. holes 58mm deep. Insert three anchors(H) into holes
and secure wall plate with three long bolts(G) and three washers(F).Tighten
screws firmly. Do not overtighten

”

Part 1b-Concrete Wal l Mounting

Concrete Wall

G

58mm

Φ7/16 (10.5mm)”

F

H

.

If you think the ribbon is too long, You can hide it at the back of the
televesion,once you want to uninstall the TV, it can help you to take out the
brackets

Magnetic removable
bubble level

3