Pyle PSWLE08 Installation Manual

TV Size Range: 37 ~65

Maximum Weight Capacity: 60kg/132lbs

VESA: 200x100-800x600

""

-4-

This product containssmall items thatcould be achoking hazard if swallowed. Keep
these itemsaway from young children

1.Make sure these instructions are read andcompletely understood before attempting
installation. Ifyou are unsure of any partof this installation,contact a professional
installer forassistance.

2.The wallor mounting surfacemust be capableof supporting thecombined weight of
the mountand the display; otherwise the structure must be reinforced

3.Safety gearand proper tools must be used. A minimumof two peopleare required
for thisinstallation. Failure to use safety gear can result inproperty damage, serious
injury or death.

!

.

Warning

This product wasdesigned to beinstalled on woodstud walls andsolid concrete walls.
Before installing make sure the supporting surface will support thecombined load ofthe
equipment andhardware. Never exceed the Maximum Load Capacity.This product is
intended forindoor use only. Use of this product outdoorscould lead toproduct failure or
personal injury.

CAUTION

Part 3-

NOTE:

Hang the screen

Hook the screen onto the wall plate. Then swing the screen down. Once the screen is
settled, pull down the Supportable lever, so that you can insert the cable.

Always use an assistant or mechanical lifting equipment to safely liftand

position heavy equipment.

Part 3-

NOTE:

Hang the screen

Supportable block

TV connection block

Wallplate

TV connection block

Wallplate

Item No.:

PSWLE08

Item No.:

PSWLE08

INSTALLATION GUIDE

www pyleaudio com..

Pyle Audio
1600 63rd st , Brooklyn,NY,11204
[phone]

Thank you for choosing our productThank you for choosing our product

2

-3-

-2-

Hardware Kit:

Hardware Kit:

Wood stud

TV connection blockWallplate

Part 1a-Wood Stud Mounting

.

Use wall plate as a template, make sure it is level, and mark three mounting holes
along the center lines of the wood studs. Drill three 3/16

)

)..

””(5mm)dia holes 2 (50mm)
deep. Level wall plate and attach to wall with three long bolts(1 and three washers
(2 by box wrench(4). Tighten screws firmly Do not overtighten

Part 1a-Wood Stud Mounting

812mm(32 )

"

Φ3/16 (5mm)”

2 50mm)

”(

812mm(32 )"

2 (50mm)”

Φ3/8 (10mm)”

2

1

Part 1b-Concrete wall mounting

.

Level wall plate and use wall as a template to mark three holes. Drill three 3/10 (8mm)
dia. holes 2 (50mm) deep. Insert three anchors(3) intoholes and secure wall plate
with three long bolts(1) and three washers(2) by box wrench(4).Tighten screws
firmly. Donot overtighten

”

”

Part

1b-Concrete wall

mounting

1

3

Supportable block

Supportable lever

Bubble level

M6× mm15 bolt

M6×16mm bolt

M8 mm×16 bolt

M8× mm20 bolt

2
2
2

F
G
H

I

A

B
C

2
2

D

2
2
2

E

ID

Description

Qty

M5 taper washer
M5 washer

2

J

2

M5 mm×15 bolt
M5× mm16 bolt

M4× mm15 bolt
M4×16mm bolt

1

2
3

3
3

4

3
1

Long bolt

Wallanchor

Long bolt washer

Box wrench

2

1

3

4

A,C,E,G

I J

B,D,F,H

4

4

Part 2-Attaching To ScreenSupportable block and TV connection block

First, select the small(A,B), medium(C,D,E,F) or large(G,H) screws. To attach
supportable block by using selected screws(A,C,E,G) and washers(I), and then
attach TV connection block to screen by using selected screws(B,D,F,H) and washers
(J). Tighten screws firmly but do not overtighten. WARING screws(A,B,C,D)need
washer, screws(E,F,G,H) don’t need washer.

Part 2-Attaching ToScreenSupportable block and TV connection block

E,G

F, H

I

A,C

B,D

J

I

J