Pyle PSW976S Installation Manual

Multifunctional wall mount

IMPORTANT: If don’t understand about right install ways, please

consult to normal installing specialist.

IMPORTANT:

Item No.:PSW976SItem No.:PSW976S

INSTALLATION GUIDE

-12-

Ideal for Flat Panels from 32 to 50""

Weight Capacity:15kg/33lbs~60kg/132lbs

Adjustable Tilt

Adjustable Roll Control

Adjusting thedisplay

Note:

This mountprovides a wealth of display adjustment to offerthebest viewing from a
number ofseating positions. SeeFig. 6.

Vertical Tilt AdjustmentAngle
Vertical adjustment angle is -5º to 15º.

Left to Right Swivel Adjustment Angle
The displaycan swivel ±60ºfrom left to right. Choose the desired position and use
provided Wrench to tighten the back bolton thetop ofthe Arm Assembly.
Stowing theDisplay -Positions the display against the wall Grasp the side edges of the
display,swivel and pullthe display intothe center position,and then pushthe display
straight backtowards the wall into the stowed position.

Use care when stowing the display to ensure thatcables do notbecome pinched.

Lateral Tiltadjustment angle is±5º.
Left to Right Pan Adjustment Angle
The displaycan pan ±60ºfrom left to right. Choose the desired position and use
provided Wrench to tighten the front bolt on the top of the Arm Assembly.

Adjusting thedisplay

Note:

Fig. 6

±60°

±60°

-5 15°~ °

±60°

±5°

www pyleaudio com..

MADE IN CHINA

Bulit in leveler system

Pyle Audio

1600 63rd st, Brooklyn,NY,11204

[phone]

-2-

-11-

Contents of the ox: Hardware shownas actual size

Make sure that none of these parts are missing before beginning
installation. If there are parts missing stop the installation and contact us.

Contents of the ox: Hardware shown as actual size

Right Bracket

Cable management clip

4
4
4
4

I
J

K
L
M

Square washer
Long bolt
Wallanchor

Long bolt washer
Spacer

ID Description

1
2

4

A

3

5

B
C

1
1

4

4

1

4

4
4

Arm Assembly
Left Bracket

Plastic Cover

M4 mm×12 bolt
M4 mm×16 bolt

M5× mm16 bolt

M6× mm16 bolt

M8×16mm bolt
M ×36mm5 bolt
M6×36mm bolt
M ×36mm8 bolt

Qty

D

4

4

4
4
4
4

E

F
G
H

A-H

L

I

K

J

M

ID

Description

Qty

1

2

3

Step 5:Using CableManagement

This mount includesa cable management feature, wherecables canbe routedalong
length of theArm Assembly. Route thesignal cablesand power cable along theCable
management clip asshown in Fig.5. Be sureto leaveenough slack for all cables.
With all cablesin place,swivel the display at eachpivot and checkthat the Arm
Assembly moves freely, without stretching ordamaging the cables.

Step 5:Using CableManagement

4

6

7

671

1

5X5 Wrench
4X4 Wrench

5

Cable management clip
Cable routing access points

Fig. 5

-10-

-3-

WARNING

We are not responsible for any personalinjury or product damagedue to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.

The suppliedwall mounting hardware is not for use onsteel studwalls orcold
cinder blockwalls. If youare uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.

Note:

Caution:This ProductLCD /PlasmaWall MountBracket is intended for use only

with themaximum weights indicated.See apparatus instructions.Use with products
heavier thanthe maximum weightsindicated may result in instability causing possible
injury .

Caution:

Fig 4 b

2,3

1

Knob

Fig 4 c

Lock
Open

Lock
Closed

Rod

Step 1: Attachbracket toTV

Check your TVmanual to confirm the diameterof bolt tobe used or choose an
appropriate bolt according to size, heightand position of the holeson your TV.See
pages 4-5 ofthese instructions for examples.

"" .

For correct installing, makesure thathook of every bracket must facingdown. Use
selected bolts, spacersand washers for installing bracketat theback of display.
Adjust two bracketsto equalheights and level. Once aligned,tightly secure the
bolts. the UP side on thetop As shown inFig.1.

Don't force thebolt intothe hole, which will causea damage of

equipments and injureof person.Don't use electric drill tofasten any bolts.

Note:

IMPORTANT:

Step 1: Attachbracket toTV

IMPORTANT

Note:

UP

Fig 1

UP

-4-

-9-

Following examples showshow to use bolts, spacersand squarewashers.

1.Somedisplays have vertical backs. Nospacer is required. Install thebracket directly
to the backof display by using boltsand square washersprovided. Asshown inFig.1a.

Step 3: Installingthe Plastic Cover

Secure the separatedPlastic Cover overthe WallPlate by pushing them
towardeachotheruntiltheylockinplace.SeeFig.3.

Step 3: Installingthe Plastic Cover

Plastic Cover

Fig. 3

Fig. 4a

Step 4:Hang the Display

Note:

With the help of an assistant, lift the display
intopositioninfrontofthewallplate.
Align theslots on themounting rails withthe
rods on the wall plate, and then lower the
display ontothe rods. (Fig. 4c) Make sure that
both rods are fully engaged before releasing
the display.

Prior to lifting the display, make sure

that theflip lock isin the openposition, as
shown inFig. 4a.

Once inplace, the lateralposition of the
display canbe adjusted bygently sliding it
along therods.

(Fig. 4b)

Step 4:Hang the Display

Note:

Safety Lock

Knob

Lock
Closed

Lock
Open

Fig 1a

M4 Fig bit M5 Fig bit

M6 Fig bit

A,B

3

I

D

3

I

C

I

2

2

E

I

M8 Fig bit

-8-

-5-

2. Some displayshave curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(M)between display and
thebracket.AsshowninFig1b.

Fig a

Brick, Concrete andStone wall:
Using a awlor nail to make wherethe nailsare located.Distance between twonails
for fixing wallmount must not less than16 . Pre-drill these holes with a 10mm drill
bit to atleast 80mm in deep hole.Use wall mountas a template to markthe location
of other threeholes anddrill the same holes. Pleasemake sure these holes arelevel
and eudipleural. Insertwall anchors(K) into each ofthese holes. Attachthe wall
mount to thewall using 4 long bolts(J)and washers(L).

”

Brick, Concrete andStone wall:

Fig. 2e

J

L

Concrete Wall

K

Concrete Wall

80

10

Fig. 2d

Fig 1b

M6 Fig bit

F

3

I

M

2

G

I

M

H

3

I

M

M5 Fig bit

M8 Fig bit

-6-

-7-

b

15 degree
viewing angle

eyelevel

a

Fig 2a

Step 2: mount to wall

First, determine the height of stand
The best height ofstand is parallelto eyelevel of a personwho sitting ona couch.
Normally,the horizontaldistance of eyelevel is about4’ from ground level.
The following twoconditions arefor determining the perfect heightof stand:

1) the distance between wall and couch(Fig2a).

2) the distance of eyelevel from groundlevel plusthe distance measured from
eyelevel of aperson sitting on couch withviewing angle of15 (Fig 2a).

For example:

1) the distance of ‘a’ is 5’-7’,the distance of‘b’ is about 1’

2) the distance of ‘a’ is 8’-13’,the distance of‘b’ is about 3’

3) the distance of ‘a’ is 14’-17’,the distance of‘b’ is about 4’
The perfect heightof stand centre will beanywhere withinb, whereyou feel
comfortable for viewing.

°

AttachStep 2: Attachmount to wall

After determining theheight of stand, follow theinstallation instructions inbelow
to install wallmount to different kinds ofwall

Using a awlor nail to make wherethe nailsare located,as shown asFig.2b. Distance
between two nailsfor fixing wall mount mustnot less than16 . Pre-drill these holes
with a 5mmdrill bit to at least80mm in deep hole. Use wall mount asa template to
mark the locationof other three holes anddrill thesame holes.

Fix the wallmount tothe wall with 4 longbolts(J) and

washers(L).

-wooden, brick, concreteand stone.

Please make sure these

holes are leveland eudipleural.

Woodenwall:

”

Woodenwall:

Fig. 2b

16”

80

5

Fig. 2c

J

L

Wood stud