Pyle PSW598UT Installation Manual

Thank you for choosing our productsThank you for choosing our products

-8-

Multifunctional double deck wall mount

Fixed Flat Panel TV Bracket

Easy installing:Just hangup thedisplay

Safety: locking by locking bar on the bottom

Max loadcapacity:60kg/132lbs

TV sizerange:42 ~65""

INSTALLATION GUIDE

IMPORTANT: If don’t understand about right install ways, please

consult to normal installing specialist.

IMPORTANT:

Item No.:PSW598UTItem No.:PSW598UT

Fig 3c

3

4

UP

UP

5

Warning: Some TV requiretwo peopleto lift, aswe arenot responsiblefor any personal
injury or productdamage dueto mishandling.

Warning:

www pyleaudio com..

MADE IN CHINA

Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
[phone]

UP

UP

Hardware List: Actual parts appearanceand thequantity may different
with illustrated.

Hardware List:

-2-

-7-

Fig 3b

3

1

3

2

2

5

4

UP

UP

Step 3: Hangingdisplay

Firstly lift the bracket mounted displayover thewall
mount. And thenhook thebrackets over the top of the
wall mount. Rotate the display let thebottom of the
brackets hook over the bottom ofwall mount, as shown
in Fig.3a. Then use the Lockingbar(3) toprevent the
display from being removed or accidentallyknocked off
of the wallplate.When thelocking bar half insertes into
the wall plate, youcan use therotating rod(4)to make
it fully inserted. (4)

Step 3: Hangingdisplay

Fig 3a

2

1

.

.

screw out the locking rod ,then the
TV is settled, if you think
the ribbon is too long,You could hideit at the back of
thetelevesion,onceyouwanttouninstalltheTV,itcouldhelpyoutotakeoutthe
locking bar

AsshowninFig.3bandFig3c

(5)

(3)

5

UP

UP

A-H

LI

K

J

M

ID Description

1
2

A

3

B

1
2

4

1

4

Wallplate
Bracket

Locking bar

M4 mm×12 bolt
M4 mm×16 bolt

Qty

41

Rotating rod

51

Ribbon

4

4
4

F
G
H

I

Square washer
Long bolt

Wallanchor
Long bolt washer

C

4

M5× mm16 bolt
M6× mm16 bolt

M8×16mm bolt

D

4

4
4

E

ID

Description

Qty

J
K

L
M

4
4

4
4

M5×3 mm6 bolt
M6×3 mm6 bolt
M8×36mm bolt

Square

-6-

-3-

After determining theheight ofstand, follow theinstallation instructionsin below
to install wallmount todifferent kinds of wall -wooden, concrete.

Using a awlor nail to make where thenails arelocated, asshown as fig.2b.Pre-drill
these holes witha 5mmdrill bit to at least 40mmin deep hole. Please makesure these
holes are level and located atcenter. Use wallmount as a template tomark the location
of other three holes and drill thesame holes. Fix the wallmount tothe wall with long
bolts(J) and washers(L).

Woodenwall:

4

Woodenwall:

Fig 2b

Brick, Concrete wall:
Using the wallmount astemplate to mark4 holeslocation on thewall.three holesare
located at thetop rowof the slots and oneis located at the centerof bottomrow.
Pre-drill these holes witha 10mm drill bit toat least 50mm deep hole.Insert wall
anchors(K) into eachof theseholes. Attach thewall mountto the wallusing 4long
bolts(J) and washers(L).

Brick, Concrete wall:

J

1

L

Fig 2c

WARNING

We are not responsible forany personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect useof this product.

The suppliedwall mounting hardware is not for use on steel stud walls orcold
cinder blockwalls. If youare uncertain about the nature of your wall, please consulta
qualified contractor. If the hardware you required is not included please contactyour
local hardware store.

Note:

Caution:This Product LCD /PlasmaWall MountBracket is intended for use only

with themaximum weights indicated.See apparatus instructions.Use with products
heavier thanthe maximum weightsindicated may result in instability causing possible
injury .

Caution:

Step 1: Attachbracket toTV

CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt accordingto size, height and positionof the holes on yourTV.See
pages 4 ofthese instructionsfor examples.

For correct installing, make surethat hookof everybracket must facing down. Use
selected bolts andwashers forinstalling bracket at the back of display. Adjust two
brackets to equal heights and level. Once aligned,tightly securethe bolts.

As shown inFig.1a.

Don't force the bolt into thehole, which will cause adamage of

equipments and injure of person. Don't useelectric drill to fasten anybolts.

Note: the

UP side on thetop"" .

IMPORTANT:

Step 1: Attachbracket toTV

IMPORTANT

Note:

Fig.1a

UP

UP

Warning: Some TV requiretwo peopleto lift, aswe arenot responsiblefor any
personal injury orproduct damagedue to mishandling.

Warning:

-4-

-5-

Following examples showshow to use bolts andsquare washers.

Install the bracket directlyto the backof displayby using bolts and squarewashers
provided. As shown in Fig.1b.

Fig 1b

b

15 degree
viewing angle

eyelevel

a

Fig 2a

Step 2: mount to wall

First, determine the height of stand
The best height of stand is parallelto eyelevel of a personwho sitting on a couch.
Normally,the horizontaldistance of eyelevel is about4’ fromground level.
The following twoconditions arefor determining the perfect heightof stand:

1) the distancebetween walland couch(Fig2a).

2) the distanceof eyelevelfrom groundlevel plus the distance measuredfrom
eyelevel of aperson sittingon couch withviewing angleof 15 (Fig 2a).

For example:

1) the distanceof ‘a’is 5’-7’, the distance of‘b’ is about 1’

2) the distanceof ‘a’is 8’-13’, the distance of‘b’ is about 3’

3) the distanceof ‘a’is 14’-17’, the distance of‘b’ is about 4’
The perfect heightof standcentre will be anywherewithin b, where you feel
comfortable for viewing.

°

AttachStep 2: Attachmount towall

A,B

2

C,F

2

D,G

2

E,H

I

I

I

I

2

M4Fig bit

M5Fig bit

M6Fig bit

M8Fig bit