Page 1
Warning: Some TV requiretwopeople tolift,as weare notresponsible for any
personal injury or productdamage duetomishandling.
Warning:
Fig 4b
Step 4: Hanging display
Firstly lift thebracket mounteddisplayover thewall mount. Andthen hook the
brackets over thetop of thewall mount. Rotatethe displaylet the bottomof the
brackets hook overthe bottom ofwall mount, asshown in Fig.4a. Then put safe
bolts into the bottomof thebrackets and lock it,as showninFig.4b.
Step 4: Hanging display
Thank you for choosing our productsThank you for choosing our products
-8-
Multifunctional double deck wall mount
Tilt Flat Panel TV Bracket
Easy installing:Just hang up the display
Safety: locking by spinning bolt onthe bottom
Weight Capacity:10kg/22lbs~50kg/110lbs
TV sizerange: 26 ~42
Adjustable angle: 5 15
""
-～
Inside has balance adjust system
Bulit in leveler system
INSTALLATION GUIDE
IMPORTANT: If don’t understand about right install ways, please
consult to normalinstallingspecialist.
IMPORTANT:
Item No.:PSW503STItem No.:PSW503ST
the facingof a quilt
Fig 4a
2,3
1
5
www pyleaudio com..
MADE IN CHINA
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
Page 2
Hardware List: Actual parts appearance and the quantity may different
with illustrated.
Hardware List:
4
4
H
I
J
K
4
4
Square washer
Long bolt
Wallanchor
Long bolt washer
Spacer
ID Description
1
2
A
3
4
5
6
B
C
1
1
1
4
1
2
1
4
4
Wallmount
M4 mm×12 bolt
M4 mm×16 bolt
M5× mm16 bolt
M6×16mm bolt
M5×36mm bolt
M6×36mm bolt
Qty
D
4
4
4
4
E
F
G
Cable Cover
Safe bolt
Box wrench
After determining the heightof stand,followthe installationinstructionsin below
to install wall mountto differentkinds of wall
Using a awl ornail tomake where thenails arelocated,as shownas Fig.3b.Distance
between two nails forfixing wallmountmust notlessthan 16 .Slide theplateinto
position as required.(Fig.3c) Pre-drillthese holes witha 5mm drillbit toatleast
40mm in deep hole.Use wallmountas atemplateto markthe location ofother three
holes and drill thesame holes.
Fixthewallmounttothewallwith4longbolts(H)andwashers(J) .
-wooden, brick, concreteand stone.
Please make surethese holesare level andeudipleural.
by box wrench(6)
Woodenwall:
”
Woodenwall:
-2-
-7-
A-F
J
G
I
H
K
ID
Description
Qty
Fig 3b Fig 3c
Brick, Concrete andStone wall:
Using a awl ornail tomake where thenails arelocated.Distance betweentwo nails
for fixing wall mountmust notlessthan 16 . Slide the plateinto position asrequired.
(Fig.3c) Pre-drillthese holeswith a 10mmdrill bit toat least 50mmin deephole.Use
wall mount as atemplate tomarkthe locationofother threeholes anddrillthe same
holes. Please makesure theseholesare leveland eudipleural.Insertwall anchors(I)
into each of theseholes. Attachthewall mounttothe wallusing 4 longbolts(H) and
washers(J)by box wrench(6).
”
Brick, Concrete andStone wall:
1
2
5
3
4
Plate
Fig 3d
H
J
1
Balance-adjusting
Using balance-adjustingsystem on theplate,
make sure whether wall plate is installed
balance. Ifnot, then slidethe wall platelet
pointer levelin the centerposition.
Left bracket
Right bracket
6
6
Page 3
-6-
-3-
b
15 degree
viewing angle
eyelevel
a
Fig 3a
Step 3: mount to wall
First, determine the height of stand
The best height ofstand is parallelto eyelevel ofa personwhositting onacouch.
Normally,the horizontaldistance of eyelevelis about 4’from groundlevel.
The following two conditionsare fordetermining the perfectheight of stand:
1) the distance between walland couch(Fig3a).
2) the distance of eyelevelfrom groundlevel plusthedistance measuredfrom
eyelevel of a personsitting oncouchwith viewingangleof 15 (Fig 3a).
For example:
1) the distance of ‘a’is 5’-7’, thedistance of ‘b’is about1’
2) the distance of ‘a’is 8’-13’, thedistance of ‘b’is about3’
3) the distance of ‘a’is 14’-17’, thedistance of ‘b’is about4’
The perfect height ofstand centrewill be anywherewithin b,where youfeel
comfortable for viewing.
°
AttachStep 3: Attach mountto wall
WARNING
We are not responsible foranypersonalinjur y orproduct damagedue to mishandling,
incorrect mounting, incorrect assembly or incorrect use of thisproduct.
The suppliedwall mounting hardware is not for use on steel stud walls or cold
cinder blockwalls. If youare uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
Note:
Caution:This Product LCD/PlasmaWall Mount Bracket is intended for use only
with themaximum weights indicated.See apparatus instructions.Use with products
heavier thanthe maximum weightsindicated may result in instability causing possible
injury .
Caution:
Step 1: Attach bracket to TV
CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt accordingto size,heightand positionof the holeson your TV. See
pages 4-5 of theseinstructions forexamples.
For correctinstalling, makesure thathook ofevery bracketmust facingdown. Use
selected bolts, spacers andwashers forinstallingbracket at the back of display.
Adjust two brackets to equalheights andlevel. Once aligned, tightly secure the
bolts.
Don't force thebolt into thehole, which willcause adamageof
equipments and injureof person. Don'tuse electric drillto fasten anybolts.
IMPORTANT:
Step 1: Attach bracket to TV
IMPORTANT
Step 2: Install the Cable Cover
Route the cables as required. Snap the cable cover into place onto
the rods (Fig. 2a), and then slide the cover into position as required.
(Fig. 2b)
Step 2: Install the Cable Cover
Fig 2a Fig 2a
Page 4
2. Some displays havecur vedbacks with
recessed mounting lands(Fig.a).It will
require theuseof spacer. Forthis display,
install a spacer(K) betweendisplay and
thebracket.AsshowninFig1b.
Fig a
-4-
-5-
Following examples showshow to usebolts, spacersandsquare washers.
1.Somedisplays have verticalbacks. No spaceris required.Install thebracket directly
to the back ofdisplay byusingbolts andsquare washers provided.As shown inFig.1a.
Fig 1a
M5 Fig bitM4 Fig bit
M6 Fig bit
A,B
3
G
2
C
G
D
G
3
Fig 1b
M6 Fig bitM5 Fig bit
E
3
G
K
K
F
G
3
Loading...