Pyle PSW449T Installation Manual

Warning: Some TV requiretwopeople tolift,as weare notresponsible for any
personal injury or productdamage duetomishandling.

Warning:

Step 3: Hanging display

Firstly lift thebracket mounteddisplayover thewall mount. Andthen hook the
brackets over thetop of thewall mount. Rotatethe displaylet the bottomof the
brackets hook overthe bottom ofwall mount, asshown in Fig.3a. Then put safe
bolts into the bottomof thebrackets and lock it,as showninFig.3b.

Step 3: Hanging display

Thank you for choosing our productsThank you for choosing our products

-8-

IMPORTANT: If don’t understand about right install ways, please

consult to normalinstallingspecialist.

IMPORTANT:

Item No.:PSW449TItem No.:PSW449T

Multifunctional double deck wall mount

Tilt Flat Panel TV Bracket

Easy installing:Just hang up the display

Safety: locking by spinning bolt onthe bottom

Max loadcapacity:60kg/132lbs

TV sizerange: 23 ~36

Adjustable angle: 5 15

""

-～

Inside has balance adjust system

Bulit in leveler system

INSTALLATION GUIDE

4

Fig 3a

2,3

1

Fig 3b

UP

UP

www pyleaudio com..

MADE IN CHINA

Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
[phone]

After determining the heightof stand,followthe installationinstructionsin below
to install wall mountto differentkinds of wall-wooden, concrete.

Using a awl or nail to make wherethe nails are located,as shownas fig.2b. Distance
between two nails forfixing wall mountmust not lessthan 12”.Pre-drill theseholes
with a 5mm drill bit to at least50mm in deephole. Please make sure theseholes are
level and located atcenter. Use wall mountas a templateto markthelocation ofother
three holes anddrill the sameholes. Fixthe wall mountto the wallwith 4 longbolts(H)
and washers(J).

Woodenwall:

Woodenwall:

-2-

-7-

Hardware List: Actual parts appearance and the quantity may different
with illustrated.

Hardware List:

6
6

H

I
J

K

6

4

Square washer
Long bolt
Wallanchor

Long bolt washer
Spacer

ID Description

1
2

A

3

B

C

1
1

4

1

4

4

Wallmount
Left bracket

Right bracket

M4 mm×12 bolt
M4 mm×16 bolt

M5× mm16 bolt
M6×16mm bolt

M5×36mm bolt
M6×36mm bolt

Qty

D

4

4
4
4

E
F
G

42

Safe bolt

A-F

J

G

I

H

K

ID

Description

Qty

Fig 2b

Fig 2c

Concrete wall:
Using the wall mountas templatetomark 6holeslocation onthe wall. Thereholes are
located at the toprow ofthe slots andthree moreare locatedat thebottomrow. The
outer holes must befall totheleft andrightof thetwo holes inthe middle ofthe
mount. Please makesure theseholesare leveland atleast6” betweenanytwo lines.
Pre-drill theseholes with a10mm drill bitto atleast50mm deephole.Insert wall
anchors(I) into each ofthese holes.Attachthe wallmountto thewall using 6long
bolts(H) and washers(J).

Concrete wall:

1

2

3

4

Using balance-adjustingsystem on theplate, make sure whether wall plate is installed
balance. Ifnot, then slidethe wall platelet pointer levelin the centerposition.

H

J

1

Balance-adjusting

UP

UP

-6-

-3-

b

15 degree
viewing angle

eyelevel

a

Fig 2a

Step 2: mount to wall

First, determine the height of stand
The best height ofstand is parallelto eyelevel ofa personwhositting onacouch.
Normally,the horizontaldistance of eyelevelis about 4’from groundlevel.
The following two conditionsare fordetermining the perfectheight of stand:

1) the distance between walland couch(Fig2a).

2) the distance of eyelevelfrom groundlevel plusthedistance measuredfrom
eyelevel of a personsitting oncouchwith viewingangleof 15 (Fig 2a).

For example:

1) the distance of ‘a’is 5’-7’, thedistance of ‘b’is about1’

2) the distance of ‘a’is 8’-13’, thedistance of ‘b’is about3’

3) the distance of ‘a’is 14’-17’, thedistance of ‘b’is about4’
The perfect height ofstand centrewill be anywherewithin b,where youfeel
comfortable for viewing.

°

AttachStep 2: Attach mountto wall

WARNING

We are not responsible foranypersonalinjur y orproduct damagedue to mishandling,
incorrect mounting, incorrect assembly or incorrect use of thisproduct.

The suppliedwall mounting hardware is not for use on steel stud walls or cold
cinder blockwalls. If youare uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.

Note:

Caution:This Product LCD/PlasmaWall Mount Bracket is intended for use only

with themaximum weights indicated.See apparatus instructions.Use with products
heavier thanthe maximum weightsindicated may result in instability causing possible
injury .

Caution:

UP

Fig.1

UP

Step 1: Attach bracket to TV

CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt accordingto size,heightand positionof the holeson your TV. See
pages 4-5 of theseinstructions forexamples.

For correctinstalling, makesure thathook ofevery bracketmust facingdown. Use
selected bolts, spacers andwashers forinstallingbracket at the back of display.
Adjust two brackets to equalheights andlevel. Once aligned, tightly secure the
bolts. As shown in Fig.1.

Don't force thebolt into thehole, which willcause adamageof

equipments and injureof person. Don'tuse electric drillto fasten anybolts.

Note: the UP side on the top"" .

IMPORTANT:

Step 1: Attach bracket to TV

IMPORTANT

Note:

Fig.1

UP

2. Some displays havecur vedbacks with
recessed mounting lands(Fig.a).It will
require theuseof spacer. Forthis display,
install a spacer(K) betweendisplay and
thebracket.AsshowninFig1b.

Fig a

-4-

-5-

Following examples showshow to usebolts, spacersandsquare washers.

1.Somedisplays have verticalbacks. No spaceris required.Install thebracket directly
to the back ofdisplay byusingbolts andsquare washers provided.As shown inFig.1a.

Fig 1a

Fig 1b

M6 Fig bitM5 Fig bit

E

3

G

K

M5 Fig bitM4 Fig bit

M6 Fig bit

2

C

G

D

G

3

F

G

3

A,B

3

G

K