Pyle PSW128ST Installation Manual

Item No.:PSW128STItem No.:PSW128ST

This product wasdesigned to beinstalled on woodstud walls andsolid concrete walls.
Before installing make sure thesupporting surface willsupport the combinedload of the
equipment andhardware. Never exceed the MaximumLoad Capacity. This product is
intended forindoor use only. Use of this product outdoors could leadto product failure or
personal injury.

CAUTION

INSTALLATION GUIDE

-8-

Thank you for choosing our productThank you for choosing our product

This product containssmall items thatcould be achoking hazard if swallowed.Keep
these itemsaway from young children

1.Make sure these instructionsare read and completely understoodbefore attempting
installation. Ifyou are unsure of anypart of thisinstallation, contact aprofessional
installer forassistance.

2.The wallor mounting surfacemust be capableof supporting thecombined weight of
the mountand the display; otherwise the structure must be reinforced

3.Safety gearand proper tools mustbe used. Aminimum of twopeople are required
for thisinstallation. Failure to use safety gearcan result in property damage,serious
injury or death.

!

.

Warning

UP

UP

TV Size Range: 23 ~37

Maximum Weight Capacity: 35kg/77lbs

Adjustable angle: 0 5

Locked by locking bar on the bottom

""

～°°

www pyleaudio com..

MADE IN CHINA

Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
[phone]

UP

UP

ID Description

1
2

A

3

B

1
2

4

1

4

Wallplate
Bracket

M4 mm×12 bolt
M4 mm×16 bolt

Qty

Locking bar

-2-

-7-

1

3

2

2

Description

Square washer
Long bolt

Wallanchor
Long bolt washer

M6×16mm bolt

M5× mm16 bolt

4

1

Rotating rod

ID

Qty

4
4

F
G

H

4

D

4
4

E

C

4

4

51

Ribbon

5

Hardware Kit:

Hardware Kit:

A-D

H

E

G

F

3

4

5

If you think the ribbon is too long,You could hide it at the backof the
televesion, once you want touninstall the TV, itcould help you to take
out the locking bar .

(5)

(3)

UP

UP

-6-

-3-

Wood stud

F

H

Part 1a-Wood Stud Mounting

.

Usewallplate(1)asatemplate,makesureitislevel,andmarkfour
mounting holes along the center lines of the wood studs. Drill four 3/16

)) .

.

”

”(5mm)dia holes 2 (50mm) deep. Level wall plate(1) and attach to wall

with four long bolts(F and four washers(H . Tighten screws firmly Do not
overtighten

Part 1a-Wood Stud Mounting

2 50mm)”(

Φ3/16 (5mm)”

Part 3-Mounting the flat panel screen

NOTE:

Hook the top of brackets onto the top flange
of wall plate(1). Then swing the screen down.

(2)

Always use an assistant or mechanical
lifting equipment to safely lift and position
heavy equipment.

Part 3-Mounting the flat panel screen

NOTE:

Use the Locking bar(3) topreventthe TV from being removed or
accidentally knocked off of thewall plate. When the locking bar half
insertes into the wall plate, you can use the rotating rod(4) to make it
fully inserted.

3

UP

UP

5

Stud finder

2

1

-4-

-5-

Part 1b-Concrete Wall Mounting

.

Level wall plate(1) and use it as a template to mark four holes. Drill four 3/8
(10mm) dia. holes 2 (50mm) deep. Insert four anchors(G) into holes and
secure wall plate with four long bolts(F) and four washers(H).Tighten screws
firmly. Do not overtighten

”

”

Part 1b-Concrete Wal l Mounting

Concrete Wall

2(” 50mm)

Φ3/8 (10mm)”

.

Part 2-Attaching Brackets To Screen

Center brackets vertically on back of screen. Select the small(A or B)
medium(C ). Attach brackets to screen using four selected screws and
four square washers(E) at the top and bottom of each bracket.

or

or D

Tighten screws

firmly. Do not overtighten

Part 2-Attaching Brackets To Screen

F

H

G

Square washer(E)

Small holefor
M4 screws

Medium holefor
M5andM6screws

E

A-D

UP

UP