Page 1
Warning: Some TVrequire two people tolift, as weare notresponsible forany
personal injury orproduct damage dueto mishandling.
Warning:
Fig 3a Fig 3b
Step 3: Hangingdisplay
Firstly lift thebracket mounteddisplay overthewall mount.And then hookthe
brackets over thetop ofthe wall mount.Rotate thedisplay let thebottom of the
brackets hook overthe bottomof wall mount, as shown in Fig.3a. Thenput safe
bolts into thebottom of the brackets andlock it, as shown inFig.3b.
Step 3: Hangingdisplay
Thank you for choosing our productsThank you for choosing our products
-8-
Multifunctional double deck wall mount
Fixed Flat Panel TV Bracket
Easy installing:Just hang up the display
Safety: locking by spinning bolt on the bottom
Max loadcapacity:60kgs/132lbs
TV sizerange: 36 ~65""
Inside has balance adjust system
Bulit in leveler system
INSTALLATION GUIDE
IMPORTANT: If don’tunderstand aboutright install ways, please
consult to normal installing specialist.
IMPORTANT:
2
1
3
Item No.:PSW116MF1Item No.:PSW116MF1
UP
UP
UP
UP
www pyleaudio com..
MADE IN CHINA
Pyle Audio
1600 63rd st, Brooklyn, NY, 11204
(718)236-8000
Page 2
Hardware List: Actual parts appearance and the quantity may different
with illustrated.
Hardware List:
6
6
6
4
I
J
K
L
M
Square washer
Long bolt
Wallanchor
Long bolt washer
Spacer
ID Description
1
2
A
3
4
B
C
1
2
2
4
4
4
Wallmount
Long Bracket
Short Bracket
M4 mm×12 bolt
M4 mm×16 bolt
M5× mm16 bolt
M6× mm16 bolt
M8×16mm bolt
M ×36mm5 bolt
M6×36mm bolt
M ×36mm8 bolt
Qty
D
4
4
4
4
4
4
E
F
G
H
4
Safe bolt
After determining theheight of stand, follow theinstallation instructions inbelow
to install wallmount to different kinds ofwall -wooden, concrete.
Using a awl or nail to make wherethe nailsare located,as shown as fig.2b. Distance
between two nails for fixingwall mountmust not less than 12”.Pre-drill these holes
with a 5mmdrill bit to at least 40mmin deephole. Please make sure theseholes are
level and locatedat center. Use wallmount asa template tomark the location of other
three holes anddrill thesame holes. Fix the wallmount to the wall with 4 long bolts(J)
and washers(L).
Woodenwall:
Woodenwall:
-2-
-7-
A-H
L
I
1
3
K
J
M
ID
Description
Qty
Fig 2b
Fig 2c
Concrete wall:
Using the wallmount as template to mark6 holes locationon the wall. Th eeholes are
located at thetop rowof the slots and threemore arelocated at the bottom row. The
outer holes mustbe fall to the leftand right ofthe two holes in the middle of the
mount. Please makesure theseholes arelevel and at least 6”between any twolines.
Pre-drill these holes with a 10mm drillbit to atleast 50mm deep hole. InsertWall
anchors(K) into eachof these holes. Attach thewall mount tothe wall using 6 Long
bolts(J) and washers(L).
r
Concrete wall:
4
2
Using balance-adjustingsystem on theplate, make sure whether wall plate is installed
balance. Ifnot, then slidethe wall platelet pointer levelin the centerposition.
J
1
L
Balance-adjusting
UP
UP
UP
UP
Page 3
-6-
-3-
b
15 degree
viewing angle
eyelevel
a
Fig 2a
Step 2: mount to wall
First, determine the height of stand
The best height of standis parallelto eyelevel of a personwho sitting ona couch.
Normally,the horizontaldistance of eyelevel is about 4’ from groundlevel.
The following twoconditions arefor determining the perfect height of stand:
1) the distance between wall and couch(Fig2a).
2) the distance of eyelevel from groundlevel plusthe distance measuredfrom
eyelevel of aperson sitting on couch withviewing angle of15 (Fig 2a).
For example:
1) the distance of ‘a’ is 5’-7’, the distance of‘b’ is about1’
2) the distance of ‘a’ is 8’-13’, the distance of‘b’ is about3’
3) the distance of ‘a’ is 14’-17’, the distance of‘b’ is about4’
The perfect heightof stand centre will beanywhere withinb, whereyou feel
comfortable for viewing.
°
AttachStep 2: Attachmount to wall
WARNING
Step 1: Attachbracket toTV
CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt according to size,height and position of the holes on yourTV. See
pages 4-5 ofthese instructions for examples.
According your displayhole's distanceto choose the bracket :
Short bracket -upto 400mmheight of landed inserts
Long bracket -up to 600mmheight of landed inserts
For correct installing, makesure that hookof every bracketmust facingdown. Use
selected bolts, spacersand washers for installing bracketat the back of display.
Adjust two bracketsto equal heights and level. Once aligned, tightly secure the
bolts. the UP side onthe top As shown in Fig.1.
Don't force thebolt intothe hole, which will cause a damage of
equipments and injureof person.Don't use electric drill to fasten any bolts.
"" .Note
IMPORTANT::
Step 1: Attachbracket toTV
Note
IMPORTANT::
We are not responsible for any personal injury or product damagedue tomishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
The suppliedwall mounting hardware is not for use on steel stud walls or cold
cinder blockwalls. If youare uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware yourequired is not included please contact your
local hardware store.
Note:
Caution:This ProductLCD /PlasmaWall Mount Bracket isintended foruse only
with themaximum weights indicated.See apparatus instructions.Use with products
heavier thanthe maximum weightsindicated may result ininstability causing possible
injury .
Caution:
Fig.1
UP
UP
Page 4
Fig 1a
M4 Fig bit M5 Fig bit
Fig 1b
2. Some displayshave curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(M)between display and the
bracket. As shownin Fig1b.
Fig a
-4-
-5-
M6 Fig bitM5 Fig bit
Following examples showshow to use bolts, spacersand square washers.
1.Somedisplays have vertical backs. No spacer is required.Install thebracket directly
to the backof display by using boltsand square washersprovided. Asshown in Fig.1a.
M8 Fig bitM6 Fig bit
A,B
2
I
E
D
2
2
I
I
2
C
I
M8 Fig bit
F
2
I
M
2
G
I
M
H
I
2
M
Loading...