Page 1
PSS6
6 Channel High Power Stereo Speaker Selector
100-Watt Power, Accepts Speaker Wires Up to 14-Gauge
Page 2
CAUTION!
RISK OF ELECTRIC SHOCK. DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT POWER CORD BEFORE REMOVING BACK PANEL COVER
TO ACCESS GAIN SWITCH.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
The PSS6 PYLE PRO Multi-Speaker Selectors lets you connect up six separate
pairs of speakers to your stereo receiver/amplier. The control center is especially
convenient if you have speaker sets in dierent rooms and want to turn them on
and o independently. You can enjoy the convenience and exibility of listening
to multiple speaker pairs simultaneously.
The control center lets you use one to six sets of speakers at a time, and is
designed to operate with a stereo receiver/amplier that has a maximum of 100
watts per channel, and with speaker systems that have a minimum impedance of
8 ohms (see “Impedance Chart” on page 5)
PREPARATIONS
• Use the PYLE PRO Speaker Selectors only with ampliers rated at 100 watts per
channel or less.
• Your PYLE PRO Speaker Selector is designed to accept any size cable up to 14
gauge non-terminated speaker wire.
www.PyleUSA.com
2
Page 3
If you’re using non-terminated speaker wire, do not use any speaker wire that is
larger than 14 gauge. The lower the gauge number, the larger the cable (e.g., 12
gauge is larger in actual physical size than 14 gauge).
• Do not hook the outputs of one selector into the inputs of another speaker
selector together.
MAKING THE CONNECTIONS
The control center divides the power from your receiver/amplier dierently to
its speaker terminals. (This is especially noticeable when you connect only one
pair of speakers. If you connect more than one pair of speakers, see “Impedance
Chart” on page 5 to selector the best terminals to connect.)
For the best performance, make the connections based on how frequently you
use each set of speakers.
CAUTIONS:
To avoid damaging your speakers or receiver/amplier:
• Be sure your receiver/amplier’s power is turned off before you make the
connections.
• Never let the speaker wire’s bare ends touch each other or the adjacent terminals
on the control center.
• Do not connect more than one pair of sepakers to each set of terminals.
www.PyleUSA.com
3
Page 4
Press open the AMP terminals on the control center, then insert your receiver/
amplier’s positive (+) wires into the positive (red) terminals, and negative (-)
wires in the nagative terminals. Then press the tabs to close them.
Notes:
• If your receiver/amplier has more than one set of speaker terminal (A and B),
connect only one or the other to the control center.
• For the best results, we recommend 14-gauge, two conductor speaker wire
(not supplied) for most connections. If you plan to located the speakers further
than 80 feet from the control center, use a heavier gauge of wire.
OPERATION
CAUTION:
• To avoid damaging your receiver/amplier, set its volume to the lowest setting
before changing the control center’s settings.
• To turn on a pair of speakers connected to the control center, simply press in the
desired button. For example, to turn on the set of speakers connected to SPK A,
press A.
• To turn off a pair of speakers, press the button again so it is in the “out” position.
Note:
if no speakers are connected to a set of terminals, do not press in the corresponding
control button.
IMPEDANCE CHART
Impedance is a measurement of the
load placed on your receiver/
amplier by the speakers. The load
placed on your receiver/amplier
from thte control center will vary
depending on how many pairs of
speakers you turn on at one time,
and on which speakers you turn on.
The chart below shows the
impedance for all possible
combinations of 8-ohm speakers.
www.PyleUSA.com
4
Page 5
Features:
Up to 6 Separate Speaker Pairs to Your Stereo System
•
• Accepts Speaker Wires up to 14-Gauge
• Handles 100Watts per Channel w/ Speaker Systems
• Minimum Impedance of 8 Ohms
• Protection Circuitry Keeps It Running Smoothly
• Play Any Combination or Sets of Speakers at Once
• Plug and Play, Easy to Install
• Impedance Protection Prevents Amplier from Damaging Low Impedance
Loads
What's in the Box:
6 Channel High-Power Stereo Speaker Selector
•
Technical Specs:
Power Supply: 100 Watts
•
• Construction Material: Iron
• Speaker Wire Size: Up to 14 gauge
• Frequency Response: 20Hz-20KHz
• Number of Stereo Speaker Zones: 6 zones
• 150watts RMS/channel. 75watts RMS/channel with impedance protection
• Number of connections: 4 red/black IN and 12 red/black OUT
• Product Dimension (L x W x H): 9.05'' x 5.9'' x 1.85'' -inches
This product can expose you to a chemical or group of chemicals, which
may include ”Nickel Carbonate” which is known in the state of California
to cause cancer, birth defects, or other reproductive harm. For more info,
go to https://www.p65warnings.ca.gov/.
www.PyleUSA.com
5
Page 6
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
Loading...