Page 1
Page 2
IMPORTANT SAFETY SYMBOLS
£
RISK
OF
ELECTRIC
SHOCK
ill
DO
NOT
OPEN
CAUTION
TO
REDUCE
THE
RISK
OF
ELECTRIC
SHOCK.
DO
NOT
REMOVE
COVER
(OR
BACK)
NO
USER-SERVICEABLE
PARTS
INSIDE,
REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL
The symbol
is
used to indicate that some hazardous live terminals are involved
within this apparatus, even under the normal operating conditions, which may
be
sufficient to constitute the risk of electric shock or death.
The
symbol
is
used
in
the service documentation
to
indicate that specific
component
shall
be
replaced only
by
the component specified
in
that
documentation for safety reasons.
@ Protective grounding terminal.
- Alternating current/voltage.
~
Hazardous live terminal.
ON:
Denotes the apparatus
is
turned
on.
OFF: Denotes the apparatus
is
turned off.
WARNING: Describes precautions that should
be
observed to prevent the danger
of injury or death to the operator.
CAUTION: Describes precautions that should
be
observed to prevent danger of
the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
• Read these
instructions
.
• Keep these
instructions.
• Heed all warning.
•
Follow
all
instructions.
• Water &
Moisture
• Water &
Moisture
The apparatus should
be
protected from moisture and rain, can not used near water, for
example: near bathtub, kitchersink or a swimming pool, etc.
· Heat
The apparatus
should
be
located away from the heat source such as radiators, stoves or
other
appliances that produce heat.
• Ventilation
Do
not block areas of ventilation opening. Failureto do could result
in
fire. Always install
accordance with the manufacturer' s instructions.
Page 3
· Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside
of
the apparatusfor
safety.
· Power Cord and Plug
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point wtere they exit from the apparatus. Do not defeat
the safety purpose
of
the polarized or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grolIlding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, refer to electrician for replacement.
· Power Supply
The apparatus should
be
connected to the power supply only
of
the type as marked on the
apparatus or described
in
the manual. Failure to do could result
in
damage to the product
and possibly the user.
Unplug this apparatus during lightning storms or when unused for long periodsof time.
· Fuse
To
prevent the risk
of
fire and damaging the unit, please use only
of
the recommended
fuse type as described
in
the manual. Before replacing the fuse, make sure the unit turned
off and disconnected from the AC outlet.
· Electrical Connection
Improper electrical wiring may invalidate the product warranty.
· Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzol
or
alcohol.
• Servicing
Do not implement any servicing other than those means described
in
the manual.
Refer all servicing to qualified service personnel only. Only use accessories / attachments
or parts recommended by the manufacturer.
• Warning
Please remember the high sound pressure do not only temporarily damage your sense
of
hearing, but can also cause permanent damage. Be careful to select asuitable volume
Page 4
CAUTION!
We should like to draw your attention to the fact that extreme
volumes may damage your hearing and/ or your headphones or
loudspeakers. Turn the MAIN MIX control and phones control
in
the
main section
fully down before you switch
on
the unit. Always be
careful to set appropriate volume levels.
1.
CONTROL ELEMENTS AND CONNECTORS
1.
1 FRONT PANEL
: , +:. :.
.
~
~
••••
c .
.~
.....
PMX63DI 6·t:HANNEL
POWERED
MIXER
SDOW
. ·:e
:·
:e,
....
c .
6
i
"
1) 3 Pin Low impedance Microphone input- This input
is
for balanced low
Is
always
on
and available ,
It
has
an
input impendance of
IK
ohm. The connector
Is
wied as: Pin 1 + shieid : Pin 3+negative (cold)
2) 1/4 Line/ High Impedance balanced input this may
be
used as either a high
Impedance microphone input or a line level device such
as
: tape players , CD
Player.
returns or radios.
It
will also allow connection from an electric guitar ,
Bass , or keyboard
It
is
a 2- conductor input with an impedance of 10k ohms.
Both the high and
low impedance impedance input may be used simultaneously.
3) Gain this
is
the volume control for each channel.
It
sends the
Signal to the master mix buss . Typical operation
is
between 4 and 8 , dependent
Upin the device (s) on that
channel , please remember that
it
acts like a pre amp ,
So if you are using a device that has a volume output control (i, e, : a tape or
CD
Page 5
Player ) you will need
to
do some level matching
by
adjusting the level controls on
Each
unit.
4)
EO
Control This
is
to
adjust the overall tone
of
the individual inputs.
It
is
set at 60Hz/ 10k
Hz.
Since
it
is
a cut or boost control, (+/- 15dB) it will add or
Diminish presence fred hens
in
the
sound.
5) EFFX Control This
is
a send control to
the
reverb buss. It controls the amount of
Reverberation added to the input
signals.
6) USB/
SO
player, this
is
a support USB/
SO
memory card MP3 / WMA music format player.
By USB/
SO
to control the volume, Typical operation
is
between 4 and 8 .
7) Master EFFX This controls the level , I echo and time of internal reverberation added
Back
to
the mix.
8) Master
EO
This controls the overall amount of EO frequencies (63 250 1 K
4k 12k Hz). This
controls allows +/-12
dB
of
boost or
cut.
9) This
is
a switch power switch, control of the machine
on
or off, will this machine start,
you
will see the blue LED indicator emit light.
10
) Power LED Indicator
11
)3.5mm input jack for use with personal music players
12) Volume
control
for
USB/
SO
~
Please
do
not
connect
microphones
to
the
mixer (or
the
stagebox/wallbox
)
as
long
as
the
phantom
power
supply
in
switched
on.
Connect
the
micro
-Phones
before
you
switch
on
the
power
supply.
IN
addition, the
monitor
/ PA
loudspeakers
should
be
muted
before
you
activate
the
phantom
power
supply.
After
switching
on,
wait
approx. one
minute
in
order
to
allow
system
stabilization
.
13
) Master Volume This controls the overall volume level of the entire amplifier.
Typical
operation
is
between 4 and 8 .
14)Tape
Volume This controls the level ,
of
the playback inputs (RCA jack
on
rear
Panel) .
1.
2BACK PANEL
Page 6
111111111111111111111111111111111111111111111111
9
+-'
--
I
111111111111
~"
...
oon",n
•
@ @
"
"
15) AC Cable this is a standard cable for use with standard voltages from
A.
C.
Wall
Outlets. It is
grounded
and
should
NFVFR
have
the
ground
pin
romovod
for
ony
Reason.
16
)Speaker output, each channel impedance
is
8.0hm
17) RETURN These 1/4 jack are for brining
in
a effects return effect or other
Line
level source. the impedance
is
10K ohms@- 10dBv.
18
) SEND
Out-this
is a 1/4 2-
conductor
line
output.
The
impedance
is 1 k
ohm
@-
10
dBv
. It is
used
to
connect
the
either
additional
power
or
as
an
additional
Recording device. This line level signal
is
a mirror image of the mail outputs.
19)Tape
play (L/R) These RCA jacks are for brining
in
a deck , CD play
or
other line
Level
source. The impedance
is
10K ohm @- 10dB
v.
20)Tape Record (L/
R)These
RCA jack are for hooking up a tape desk to record from
The
mixer.
Both channels are summed into mono for compatibility. The signals are
Taken pre-master section , meaning thatthey are without reverb or the master tone
Section
and
does not include the tape
in
signal , the impedance
is
1 k ohm @- 10dNv.
2.
1 Mains
connection
AC POWER
IN
2.INSTALLTION
Connect the power supply to the 3-
pin
mains connector
on
the rear
of
the console.
Use the
AC
adapter supplied to connect the console to the mains. The adapter complies
with
all
applicable safety standards.
Q Please use
only
the
power
supply
unit
provided
with
the
console
.
Page 7
~
Never
connect
the ME
to
the
power
supply
unit
while
the
latter
is
connected
to
the
ains I First
connect
the
console
to
the
power
supply
unit, then
connect
the
power
supply
unit
to
the
mains.
2.
2Audio
connections
You will
need a larger number of cable for the various connections
to
and from the
console. The illustrations below show. Thewing of these cables.
Be
sure to use only
high-grade cable.
Please
use commercial RCA cables to wire the 2-track inputs and outputs.
You
can, of course, also connect unbalanceddevices to the balanced input/ outputs.
Use either mono
plugs, or ensure that ring and sleeve are bridged inside the stereo plug
(or pins 1 & 3
in
the case of XLR connectors) .
Caution
I Never
use
unbalanced
XLR
connectors
(PIN 1
and 3 connected) on
the
MIC
input
connectors
when
using
the
phantom
power
supply.
Balanced
use
with
XLR
connectors
I
nput
1 =groud I shield
2=hot
(+ve)
3=co
ld
(-ve)
3
Output
For
unbalanced
use
pin 1
and
pin 3 have
to
be bri
dged
Fig.
2.
1:
XLR
connections
Page 8
strain relief clamp
sleeve
Unbalanced
use
of
1/4
" TRS
connector
sleeve
ground shield
r r'!tt-'., .. q
---!----
tip
signa
l
The foo t swit
ch
con nects the two poles momenta
ril
y
strain relief ciamPi
sleeve
ring
tip
Fig
. . 2: 1/ 4
mono
plug
Balanced
use
of
1/4
"
TRS
connector
sleeve
gro
shield
ring
cold(-
vel
tip
h
ot(+ve)
For connecti
on
of balanced and unbalanced plus,
rig and sleeve have to be bridged at the stereo plug
Fig
. 2. 3: 1/
YI
stereo
plug
Page 9
Headphones
connection
with
1/4" TRS
connector
strain relief clamp
sleeve
ring
tip
sleeve
ground shi eld
ring
ri
ght signal
tip
left signal
Fig
. 2. 4:
Stereo
plug
for
headphones
connection
3. SPECIFICATIONS
Mono inputs
Microphone inputs (XENYX Mic Preamp)
Type XLR, electronically balanced,
discrete input circuit
Mi
c E.
I.
N. (20 Hz - 20 kHz)
@ 0 n source resistance
@ 50 n source resistance
@
150 n so
ur
ce res istance
Frequency response
Gain range
Max.
Input level
Impedance
Signal- to
noise ratio
Distortion (
THD
+ N)
Line input
Type
Impedan ce
- 134 dB / 135 . 7
dBA
-weighted
-
131
dB / 13
3.3
dBA
-weighted
- 129 dB /
130. 5
dBA
-weighted
<10 Hz - 150 kHz (-1 dB
),
<10 Hz - 200 kHz (- 3 dB),
+10 to +60
dB
+12 dBu @+10 dB gain
approx.
2.
6 kQ balanced
110
dB / 112 dB A-weighted
(0 dBu
In
@ +22 dB gain)
O. 005% / O. 004% A- weighted
1/4" TRS connector,
Electronically balanced
approx. 20Q banlanced
Page 10
Gain range
Ma
x.
Input lev
el
Channel
Equalization
Frequency:
Hz
High : @10K
Lo
w: @60
Master 5-band
graphic
equalizer
Frequency:
Hz
60
250
1K
4K
12K
Effects
Loop
Effects send
Type
Impedance
Ma
x.
output lev
el
Effects return
Type
Impedance
Ma
x.
output lev
el
Control room outputs
Type
Impedance
Ma
x.
output lev
el
Headphones output
Type
Ma
x. output lev
el
Parallel output
Power output
10k
Q unbanlanced
-
10
to +40 dB
+22 dBu
@ 0 dB Ga
in
control range
+/-
15dB
+/-
15dB
control range
+/-
12dB
+
/-
12dB
+/-
12dB
+/-
12dB
+/-
12dB
1/ 4" TS connector, unbalanced
appro
x.
1 k ohm
- 10dBv
1/ 4" TS connector , unbalanced
appro
x.
10k ohm
- 10dBv
RCA, unbalanced
appro
x.
1 k ohm
- 10dBv
1/
4"
TRS connector, Stereo
+
19
dBu / 150Q(+25 dBu)
200Watts PMS 40hms
r::r
you
can
connect
two
or
a 8 Ohm speakers
or a 40hm
speakers,
but
did
not
allow
connect
two
40hm
horns
.
Protection Circuit Power
on
Mute 2 seconds
Loading...