Pyle PLVSHR-77 Owners manual

7" WIDE SCREEN 16:9 TFT-LCD MONITOR

PLVSHR77

1. Table of Contents------------------------------------- 1

2. Warning ----------------------------------------------- 1

3. Installation -------------------------------------------- 2

4. Features ----------------------------------------------- 3

4.1 Features ------------------------------------------- 3

4.2 Remote Control Bar ------------------------------ 3

4.3 Function keys at front panel --------------------- 4

5. Installation for Monitor ------------------------------ 5

6. Accessories ------------------------------------------- 7

7. Specifications ---------------------------------------- 7

1

3. INSTALLATION

1. Rotate the locking knob on the neck of the
mounting stand clockwise.

2. Slide the engagement head on the mounting
stand into the slide bracket slot on the rear of
the monitor housing.

3. Rotate the locking knob counterclockwise
until it is hand-tight and the monitor is securely
fastened to the neck of the mounting stand.

4. Locate a desirable spot in your vehicle for the
monitor. Hold it place there, with the mounting
plate resting in approximately the right location
and have a friend sit in the seat from which you
intend viewing of this monitor to take place to
confirm the location of the monitor. If necessary,
loosen the angle adjustment knob and rotate the
monitor to a more ideal angle and retighten.,

5. Once you have confirmed the location of the
monitor, remove the adhesive backing from
the underside of the mounting plate and firmly
press all the "petals" of the mounting plate
down to the car surface. Temporarily remove
the monitor by loosening the locking knob, and
use three screws in the locations indicated in
the drawing below to further secure the monitor
mounting plate. If necessary, drill pilot holes to
assist in inserting the screws.

6. Reinstall the monitor onto the neck of the mounting
stand and tighten the locking knob. Adjust the monitor
angle again as required, being sure to tighten the angle
adjustment knob when you are done.

2

4. Function:

4.1 Features

10

RED

11

YELLOW

12

RED

8

9

13 BLACK

1. Headphone Jack

2. Power

3. UP key

4. IR Sensor

5. Down key

6. Menu

7. AV-IN Jack

4.2 Remote Control Bar

TV/AV

MUTE

FM/AM

POWER

3
7

SETUP

Monitor

UP

FUNC

+

DN

MODE

-

POWER
MUTE

4
8

FUNC

UP
MODE

DOWN

To adjust functions of Monitor, use only 5keys:

Power: Press the Power button for ON/OFF

Mute: To shutdown Audio output

Function: Press the Function button to access On Screen

Display Menu of: CONTRAST / BRIGHTNESS /

COLOR / SHARPNESS / SOURCE IN /

VOLUME / MODE / LEFT RIGHT

/ RECALL / EXIT

UP+: To Adjust Volume Up

DN-: To Adjust Volume Down
MODE: Selection button for AV1 / AV2

TV/CATV

1
5
9

2
6
0

CHVOL

8. Interface cable

9. System Cable

10. Audio in (Red RCA Jack)

11. Video in ( Yellow RCA Jack)

12. Power Wire (Red)

13. Grounding Wire (Black)

3

4.3 FUNCTION KEYS AT FRONT PANEL

1. MENU FUNCTIONS

CONTRAST: Press or to adjust Contrast.
BRIGHTNESS: Press or to adjust Brightness.
COLOR: Press or to adjust Color.
SHARPNESS:
SOURCE IN: Selection button AV1 / AV2 for

VOLUME: Press or to adjust Volume.

MODE: 16:9 / 4:3
LEFT / RIGHT: Left/Right Revolving
RECALL: The Display will Return to The

EXIT: Exit Menu Mode.

Press or to adjust Sharpness.

Original by Factory.

1. POWER
Press the POWER button once it will be power ON. Press it
again. The will be power OFF.

2. UP / DOWN
Press "UP+" or "DN--"directly is to adjust volume. Using MENU
button together can adjust the other functions.

4

5. Installation for Monitor

Note

It is recommended that the fitting is carried
out at a specialist workshop.

5

8

Release Key

6

6. ACCESSORIES

(1) Monitor Stand x 1

(2) System Cable x 1

(3) Operation Manual x1

(4) Release Key x1

(5) Remote Controller x 1

(6) Warranty Card x 1

7. Specifications

1. Supply voltage 12Vdc 10%

2. Power consumption:

3. Operating temperature: 0 C ~+ 60 C

4. Storage temperature: -25 C ~ +70 C

5. Monitor screen size 7" ( 16: 9)

6. Operating system TFT active matrix.

7. Resolution 1440 x 234 dots.

8. Monitor overall dimension: 190(W) x 126.8(H) x 36(D) mm.

9. Monitor weight: 450 20 g

10. System NTSC / PAL Dual System View Area

11. Viewing angle (L/R; T/D): L/R:45/45 :Top/down :30/60 degrees

12. Video input range: 0.5~1.25Vp-p/75 Ohms composite signal.

13. Audio input range: 0~1.5Vp-p/620 Ohms 50Hz ~ 20K Hz.

14. Audio output power: 0.5W(Max.)

The specifications are subject to change without prior notice.

1A 10%

7