Pyle PLVSHR-6 Owners manual

6 TFT LCD COLOR MONITOR

OPERATING INSTRUCTIONS

Before operating this set, please read these instructions completely

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Congratulations for purchasing our video mobile multimedia
products, before connecting, operating or adjusting this products,
please read these instructions compactly to make your particular
mobile multimedia products to best perform.

1.Do not repair it by yourself, if any trouble occurs, please
immediately shuts it off and contact our company or local dealer.
This monitor is composed of many precise electronic components,

7

any detachment or reassembling may result damages to the set.

2.Do not exposed it in humid air, dust, vapor, oil lampblack,
sunlight, etc.

3. Do not use thinner or any other chemical cleaner. Please
choose soft cloth to clean the dirt on the monitor.

4. Keep the monitor far from extremely heating or cooling places.
Storage temperature: -25~ +60 C
Operating temperature: -10- +50 C

o

o

5. Prevent the set from falling or struck.

Caution

To ensure security, please do not operate the monitor watch
video or it while driving.

Special hints

There may some blink dots in the screen, it's common
phenomenon in active matrix display technology, but not a
defect or trouble.

1.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Control and layout

1
2
3

4

5

6

7

8

Monitor

(1) Adjust Increase
(2) Menu (volume, brightness, color, contrast)
(3) Adjust Decrease
(4) Power on/off
(5) Remote sensor
(6) Audio out (earplug)
(7) Audio / video in
(8) Connecting cord

Remote Control

Power on/off

(1)
(2) Timer switch
(3) Preference switch

Adjust Decrease

(4)
(5) Mute
(6) Memory
(7) Picture up, down, left, right

Adjust Increase

(8)

Menu (volume, brightness, color, contrast)

(9)

1

2

4

6

7

5

8

9

3

2.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Installation

Video output

Audio input (red)

Video input (yellow)
Ground (black)

DC 12V power input (red)

Remote Control replacing batteries

PULL OUT

1) Always use new batteries when replacing the old set.

2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

3)Battery replacement is necessary when remote control acts sporadically or stops
operating this.

4)Do not drop, apply shock or step on the remote control

5)Do not spill water on the remote control

6) Do not place objects between the remote control and remote sensor.

7)Do not use remote controls for other equipments at the same time.

8)If the MONITOR does not operate even when operating the remote control from
a close range, it is time to replace the batteries (use CR-2025), refer to the label
on back of the basic control.

3.

PUSH

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Operating instructions

1)Press MODE button to select brightness, contrast and volume
control, press + or - to adjust correspondent analog.

2) Press PP to select the preset analog.

3) Store your favorite
When you have set desired brightness, color, contrast and Volume, press
STORE, then press PP, the screen will display STORE PP, press STORE
again, STORE in screen will turn into green, the moment analog has been
stored, in the future to call out this setting return to the stored state, you only
need to press PP button.

Technical parameters

LCD Drive Method: TFT Active Matrix
Display Size: 6 Inch (diagonal)
Aspect: 4:3
Display Format: 320 x RGB x 234
Number of Pixels: 224,640
Video System Input: NTSC
Back Light: High Brightness Type U Shaped CCFT
Power Source: DC12V
Current Consumption: 8W
Dimensions: 113 x 156 x 26 (mm) w/o headrest kit

Supplied accessories

Wire cord
Stand
Remote control
Headrest bracket
Key

1
1
1
1
2

4.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Bracket 1

for mounting stand style purpose

Mounting stand

Bracket 2

for headrest frame style use purpose

Key- for eject the monitor from

headrest frame

5.

Headrest frame

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Use bracket 2 for headrest frame style

Remove the bracket 2 from the
monitor and install bracket 1 as
folloes diagram for stand style use

Bracket 1

for mounting stand style purpose

Use bracket 1 for stand sytle

Bracket 2

for headrest frame style use purpose

6.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

液晶彩色顯示器使用說明書

Step of install headrest frame

Setup work

Remove the headrest and set it in an
uncluttered work area. Take the appropriate
precautions to ensure that it is not damaged
during the installation.

Measurements

Push on the headliner with your fingers to make
sure there are no obstructions that would hinder
the installation. Use the paper template to mark
the area to be cut.

Cut the headrest

Using an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonalyl across, stopping 1/4 inch in
from the other corner, repeat the procedure
for the other two corners.

7.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Remove form & obsturctions

Carefully peel back the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner or the foam
and use the blade to cut underneath. Remove
small section at a time, using the pull up and
cut method for uniform depth. Use a dremel or
other appropriate tool to remove other
obstructions. Insert the monitor to measure the
fit and make adjustment if necessary

Route the cable through th e headrest

Run the supplied cable through the opening
and out the bottom of the headrest. If possible,
conceal the wires using a shaft covering.
Connect the power, ground and video leads to
test the MONITOR.
Before connecting the monitor, pull the
connecting cable assembly through the
headrest frame as shown in diagram. Place
headrest frame into the opening and secure with
correct fasteners.

Install the headrest frame

Pull the connecting cable through the center of
the frame as shown in diagram, the secure with
correct fasteners

8.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

液晶彩色顯示器使用說明書

Preparing to insert monitor

Adjust the bracket pin to 90 , run the
cable through the frame as diagram
shown and connect it.

Inert the monitor

Push to insert the monitor to the
headrest frame

o

9.

LCD COLOR MONITOR OPERATING INSTRUCTIONS

Swivel an angle

Push up or down to adjust a suitable
angle.

Detachable

Insert the key between the monitor
and headrest frame gap and pull
out to remove the monitor from the
headrest frame.

10.