Pyle view PLTS76DU User Manual

PLTS76DU

7'' Single DIN In-Dash Detachable Motorized Touc h Screen TFT/LCD Monitor

w/ Digital Video/CD/MP3/MP4/USB/SD/AM-FM-RDS Player

USER MANUAL

To ensure safety while driving

and to comply with laws,

drivers should not watch video or

operate the video device while driving.

Content

Precaution......................................

Safety Information.........................

Disc Note.......................................

Installation ....................................

Detaching control panel ....................

Attaching control panel .....................

Electric Connection ......................

Remote Control ...........................

Basic Operation............................

Loading/Ejecting a DISC .................

Open/Close Monitor and Angle

Adjustment......................... ........

TFT Monitor Adjustment ................

Audio Quality Adjustment.................

Setting Time...................................

Setting Audio Mode .........................

Reset Factory Settings....................

Rear View Camera

External Audio Source ....................

Control Panel ................................

Unit keys ........................................

Radio Operation............................

Listening to radio ...........................

Storing and Listening to a Memory

station......................................

Automatic memory storing &

program scanning.......................

RDS Function ................................

Media Operation............................

Basic Operation..............................

Selecting Play Modes......................

On-Screen Display Function............

........................

Digital Video Special Function.......

2

Multi-subtitle language function........

3

Multi-audio language function...........

4

Tit le menu function ..........................

5

Media Setup Menu..........................

7

System Setup..................................

8

Language Setup..............................

9

Video Setup

10

Digital Setup ...................................

13

AUX Operation...............................

13

USB Operation...............................

SD/MMC Card Operation................

13

MP3/WMA/JPEG/MPEG4 Play..........

14

Specification.................................

15

Troubleshooting ...........................

15

16

17

20

21

24

25

27

-1-

....................................

28

29

31

32

33

34

35

36

37

38

39

Precaution

THANK YOU FOR PURCHASING THIS CAR DIGITAL VIDEO PLAYER .

Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit .

ON INSTALLATION

DO NOT install any receiver in locations where;

- it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.

- it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.

may obstruct visibility.

- it DO NOT operate any receiver while manipulating the steering wheel, as this may result in a traffic accident. The driver must not watch the monitor while driving. IF THE DRIVER watches the monitor while driving, it may lead to carelessness and cause an accident. IF YOU NEED carefully or you may be involved in a traffic accident. IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the monitor, and no playback picture will be shown.

- This warning appears only when the parking brake the parking brake system built in the car ( refer to the electric connection)

ABOUT

Do not press on the LCD panel on the unit as doing so can distort the picture or cause a malfunction . The picture may become unclear , or the LCD panel may be damaged .

NOTES ON CLEANING

-Clean the LCD panel with a slightly damp soft cloth.

-Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray .

-Do not use alcohol to clean the screen .

If your car was parked in a cold or hot place, the picture may not be clear . The monitor is not damaged . The picture will become clear the temper ature in your car becomes normal

THE LIQUID CRYSTAL DISPLAY (LCD) PANEL

to operate the receive while driving, be sure to look ahead

wire is connected to

.

-2-

Safety Information

CAUTION:

THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .

HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

THIS DEVICE

IS INTENDED FOR CONTINUOUS OPERATION.

REGION MANAGEMENT INFORMATION:

This Digital Video Player is designed and manufactured to respond to the Region Management Information that is recorded on a Digital Video disc. If the Region number described on the Digital Video disc does not correspond to the Region number of this

Digital Video Player, this Digital Video Player cannot play this disc.

-3-

Disc Note

Disc formats supported by this player

Digital Video

VCD

CD

MP3

Digital Video

VCD

CD

MP3

Audio and Video Disc size 12 cm

Audio Disc size 12 cm

Discs which cannot be played with this player

Digital Video-RAM CDV CDG

Handling and Cleaning

Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging.

not place discs in the following

Do places:

1.Direct sunlight

2.Dirty, dusty and damp areas

3.Near car heaters

4.On the seats or dashboard

Disc Cleaning

Use a dry soft cloth to wipe the surface. If the disc is quite dirty, use a soft cloth slightly moistured with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.

Note:

A disc may become somewhat scratched (although not enough to make it

unusable) depending on your handle it and conditions in the usage environment.

Note these scratches are not an indication of any problem with the player.

Label side up

Do not touch the underside of the disc

Do not bend

Wipe the disc from center toward the outside edge

Preparing New Discs with Rough Spots

A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the proper setting will not be performed and the player will not play the disc. Therefore, remove the rough edges in advance by using a ball point pen or pencil shown on the right. To remove the rough edges, press the side of the pen or pencil against the inside and outside edges of the disc.

Rough spots on outside edge

Ball point pen or pencil

Rough spots on inside edge

-4-

as

Installation

NOTES:

Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications of

Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

If installation angle exceeds 30 from horizontal, the unit might not give optimum performance.

the vehicle.

system work properly.

'

its

30

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt

or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from "Front"(conventional DIN Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

-5-

Installation

Installating the unit

DASH BOARD

HEX NUT

SPRING WA SH ER

PLAIN WASHER

TAPPING SCREW

SCREWDRIVER

METAL MOUNTING STRAP

TAB S

CONSOLE

KEY PLATE

SLIDE BRACKET HOUSING

HEX BOLT

If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into left and right side of chassis as above illustration.

PLASTIC TRIM OUT

KEY PLATE

-6-

Installation

How To Remove And Install The Front Panel

When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder.

Detaching Control Panel

Before detaching the control panel, be sure to turn off the power.

1). Press the “REL” release button and the right hand side of front pane will release

First pull up the panel as the direction indicated by the arrow (See )And then

taking out the panel as the direction indicated by the arrow (See ).

1

2

REL button

2). Put the front panel in the protective case for safe keeping.

1

protective case

2

-7-

Installation

ATTACHING CONTROL PANEL

1). First, insert the left side of the front panel into the main unit(SEE ). (Note: the “Hollow ” point on the front panel must be attached into the “Bulge” point of the unit . )

2). Gently push the

(SEE )

2

right-down hand side of the front panel until you feel a “ Click” .

Bulge

Hollow

1

2

Precautions

Do not touch the contacts on the front panel or the unit body, since this may result in poor electrical contact. If dirt or dust accumulates on the contacts , wipe them with a clean, dry cloth .

-8-

Electric Connection

WIRING CONNECTION

REAR RCA OUTPUT

RCH RED

LCH WHITE

RADIO ANTENNA JACK

CABLE

RCA CABLE

FRONT RCA OUTPUT CABLE

ISO CONNECTOR

REAR CAMERA INPUT YELLOW

SUBWOOFER GREY

VIDEO IN YELLOW

FRONT RCA RED R

VIDEO OUT

YELLOW

FRONT RCA WHITE L

(B+)12V REAR CAMERA SWITCH

(B-)PARKING BRAKE

AUTO ANTENNA

FRONT RCH SPK.

REAR RCH SPK.

IGNITION SWITCH(B+)

MEMORY BACK-UP(B+)

GROUND(B-)

FRONT

LCH SPK.

REAR

RED

YELLOW

BLACK

CHOKE BOX

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

PINK

BROWN

BLUE

GREY

GREY/BLACK

VIOLET

VIOLET/BLACK

Note:

the earth connection cable (parking brake B-) must be connected in order for pictures to be played back to the monitor. If the cable has not been correctly connected, the message “PARKING BRAKE” appears on the monitor.

-9-

Remote Control

MENU

SETUP

ENTER

1

2

3

4

5 6

7

8

9

0

VOL

SEL

A/PS

MUTE

STOP

MO/ST

POWER

CLK

PLAY/PAUSE

EQ

BAND

VOL

OSD

TITLE/PBC

LO/DX

GOTO

+10

ZOOM

Ref #

1

Button

CLK

15

7

17

POWER

REPEAT

PLAY/PAUSE

ZOOM

19

2

13

22

6

14

24

18

11

10

4

8

Press it briefly to view the clock time .

MENU

LO/DX

OSD

BAND

TITLE/PBC

SETUP

MODE

ENTER

TOP

RDM

Function

MO/ST

INT

AF

TA

16

3

5

20

1

21

23

9

12

27

26

25

2

3

4

5

6

7

MODE

STOP

SETUP

MO/ST (AUDIO)

SUBTITLE LOCAL/ DISTANT

REPEAT

Press it to select a desired work source. Press once to pause playback. Press PLAY/PAUSE to resume

playback. Please note: if you press STOP twice, playback will start at the beginning of the disc.

Press this button to open the SETUP menu.

In Radio mode, press this button to change between Mono and Stereo reception modes (when a station is weak, sometimes switching to Mono will improve sound quality). In Disc Playback mode, pressing this button opens the AUDIO setup menu for making changes to the way the soundtrack is reproduced.

In Digital Video Disc Playback mode, pressing this button will allow you to change the subtitle language on discs which have this as an option. In Radio mode, press this button to change the radio reception sensitivity in stations are near or far.

Pressing the button will open a menu presenting you with the playback repeat options available for that kind of disc .

-10-

Remote Control

Ref #

8

9

10

11

12

13

14

16

17

18

19

Button

GOTO

/

SEL

VOL+/-

///

Menu SubWoofer ( )

BAND (OSD)

POWER15

PLAY/ PAUS E

MUTE

TITLE/ PBC(A/P)

Function

Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed.

Press these buttons to skip ahead or back one track.

Briefly press this button repeatedly to switch between BASS,TRE, BAL, FADER,COLOR,BRIGHT,CONTR,TINT and VOL; Long press this button to switch REG, then briefly press this button repeatedly to switch between PI, TA, AF, LOUD, SWF,EQ,DX/LOCAL(in radio mode),STEREO/MONO (in radio mode),TIME 24H/12H, CLOCK, BUZZ,EUR/USA FREQ,ANIMA, BG and LED; After switching a desired item above, VOL- button to set.

press the VOL+ or

Use these controls to adjust the volume level.

Press to navigate the various menus present in the product.

Press this button briefly to display the root level directory of a Digital Video disc. Press and hold this button to turn on or off the SUBWOOFER output.

In Radio mode, press this button repeatedly to switch between the five radio bands: FM1 > FM2 > FM3 > AM1 > AM2. In Disc Playback modes, Press this button to see information about the disc currently in play.

Press this button to turn the unit ON , press it again to turn the unit OFF.

In Disc Playback mode, press to pause playback. Press again to start where playback stopped.

Press this button to turn off the audio. Press again to restore the sound to its

prior volume level.

Display the TITLE menu that is stored in Digital Video disc changing between PBC ON and PBC OFF on the VCD disc. In

Radio mode, press and hold this button to start the Auto-Program mode, during which the tuner will scan for all strong stations and assign them

to the radio preset buttons.

Press this button to Open/Close the operate monitor .Long press it to adjust the angle of monitor Upward/Downward

ZOOM

20

21

EQ

22

Shortly press it to increase the picture in size .

Press repeatedly to cycle through the different equalizer curve presets you may wish to use for enhanced listening.

In Disc Playback mode, press for fast forward playback.

-11-

Remote Control

Ref #

23

24

25

26

27

Button

ENTER

0-9

+10

1-6

This button is used to confirm selections and settings within many of the menus in the OSD system.

In DISC mode, press it to reverse rapidly

Use to input numerical values during programming, with the GOTO button, or to directly select a track to play . In Radio mode, (when the RDS engaged,), 0 serves as TA function, 9 serves as the AF function .

This button is used with the other number buttons for use with two-digit number entries.

Six numbered preset buttons store and recall stations for each band

Function

Preparing the Remote Control

Inserting the Battery

1.First push to inside as the direction indicated by the arrow (See )And then

Remove the battery holder as the direction indicated by the arrow (See ).

2.Replace the battery Set a new battery property with (+)side up as illustrated

(See

3.Insert the battery holder. Push in the holder to the original position(See ).

).

3

1

2

4

Using the Remote Control

Face the remote control towards the player front face IR mark (remote control signal

receiver).

Operation angle: About 30 degree in each the direction of the front of the IR mark.

Note :

The lithium cell in the battery compartment of remote control has been secured for

transport with a foil . Before initial use please remove this foil so that the remote control is ready for operation .

-12-

Basic Operation

POWER ON/OFF

Touch the “OFF” ICON on screen to turn the unit off . Press the“ ” onthe front panel to turn It on, press it again to turn off .

LOADING/EJECTING A DISC

Loading a Disc

1. Press the POWER ( ) button on the front pane to turn the device on .

2. Insert the disc with printed side facing up into the disc slot (1) .

3. The player starts playback the disc automatically .

1

Ejecting a Disc

In disc mode, Press the (2) button on the front panel to eject the disc .

2

FIG.2

Adjusting the viewing angle . When the monitor does not move, you press button on the panel to turn the monitor upward or downward at fine steps to get a desired viewing angle .

FIG.3

Do not rotate the monitor forcibly to avoid mechanical damage .

OPEN/CLOSE MONITOR AND ANGLE ADJUSTMENT

Touch OPEN button on front panel, the monitor will draw out automatically .

FIG.1

OPEN/CLOSE button

When the monitor draws out to a certain location, it will turn upward automatically and stop at vertical position .

FIG.4

Return the monitor to the central viewing position, then press OPEN button on the front panel , the monitor will turn downward automatically .

FIG.5

-13-

Basic Operation

When the monitor turns downward to a certain angle, it will draw in .

Touch the “S ET ” ICON on touch screen to enter the setting mode, the message will display like following :

FIG.6

TFT Monitor Adjustment

In Radio mode, touch the“ RADIO ” icon or In media mode , touch the range to enter the home menu, the message like following as below.

(1) (2)

(3) (5)

(1). SET button

touch to enter the SETTING mode .

(2). OFF (Power) button

in any modes, touch the “ OFF ” ICON to switch the unit off .

(3). Button

Touch to close the monitor .

(4). Button Touch to eject the disc form the disc slot.

(5). to adjust the angle of monitor down ward until your desired angle .

Button

(6). Button

to adjust the angle of the monitor

upward until your desired angle .

(6)(4)

BRIGHTNESS

CONTRAST

COLOR

15

Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.

Touch “SYSTEM” on the setting menu, touch the “ / ” ICONS to select the adjustment item, touch the “ / ” ICONS to adjust the selectment item, it depends on your habit to setup the data.

ADJUSTABLE ITEMS:

BRIGHT: 0 to 32

Adjust if the picture is too bright or too dark.

CONTRAST: 0 to 32

Adjust the contrast of the bright and dark portion.

COLOR: 0 to 32

Adjust the color for the picture-lighter or darker.

TINT: 0 to 32 Adjust the tint if the human skin color is unnatural.

-Adjustable when “NTSC “ is selected for “NTSC/PAL “ .

ANIMATION

In RADIO mode, you can change the playing time of animation among of “OFF, 10S, 30S, 1M,1.5M, 2M, 3M and 4M ”.

Note:

Please set the playing time of the ani mation to “ 10S ” for the first, when you

turn the unit on .

-14-

Basic Operation

SETTING WALLPAPER

in wallpaper mode, you can select the among of “AUTO, GREEN, YELLOW, RED,

LIGHT BLUE, BLUE, PINK ” .

When you select the “AU TO ” item, the player will change the background automatically .

SETTING LED LIGHT (3 COLORS) In

LED COLOR mode, you can select the

color among of “A uto, Blue, Red, Pink ” . When you select the “AUTO” item, the

player will change the panel color illumination automatically .

AUDIO QUALITY ADJUSTMENT

In Radio mode, touch the screen of the “ RADIO ” ICON to enter the home menu, touch the “ SE T ” ICON to enter the Setting mode, the message will display in the screen :

BALANCE: R 0-10 to L 0-10 .

Adjust sound balance between left and right speakers .

FADE: F 0-10 to R 0-10

Adjust sound balance between front and rear speakers .

SUB-WOOFER: ON or OFF

LOUDNESS: ON or OFF

RADIO LOC: LOC or DX

RADIO STEREO: STEREO or MONO

BUZZER: ON or OFF

SETTING TIME

In SETTING mode, touch the “TIME” range to select the time mode .

TREBLE

BASS

+06

Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.

Touch the “ SOUND ” section on the setting menu, touch the “ / ” ICONS to select the adjustment item, touch the “ / ” ICONS to adjust the selectment item , It depends on your habit to select the Audio

mode . Then touch the “SET ”

icon to return to the previous playback .

ADJUSTABLE ITEMS:

TREBLE: -7to +7

Adjust treble level .

BASS: -7 to +7

Adjust bass level .

HOUR

MINUTE

24H/12H

11:36 AM

Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.

Tou c h the “ TIME ” section on the setting menu, touch the “ / ” ICONS to select the adjustment item, touch the “ / ” ICONS to adjust the selectment item, then touch “ SET ” icon to confirm. It`s depend on your need to setup the data.

ADJUSTABLE ITEMS:

Hour adjustment: 0-23 Minutes adjustment: 0-59 Tim e format selectment : 24H/12H

-15-

Basic Operation

87.50

FM1

MHZ

DX

ST

USER

1 2

388.50 90.00 98.00

65

4

80.50

103.00106.00

Setting Audio Mode

In any modes, touch the “EQ” range on the touch screen (or press the EQ button on remote control) to select one of the preset sound modes: ROCK/POP/ JAZZ/CLASSIC/USER .

EX.: In RADIO mode

USER

DX

103.00

The information will display in the

monitor as follow :

ROCK

POP

It depends on your habit to select the

80.50

USER

Audio mode .

Reset Factory S ettings

RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object.

JAZZ

CLASSIC

Rear View Camera

When connecting the rear view camera the mirror image of the rear view is automatically displayed on the monitor when you change the gear to the back position. (Note: additional monitor can not display the image.)

EXTERNAL AUDIO SOURCE

On the front panel of the unit , there is an AUX IN jack, to connect analogue replay devices. Use this jack to replay sound of other replay equipment such as Digital Video players, computers, etc. Via the loudspeakers.

1). Please f connect the external device with stereo jack plug the AUX

2). Press the MOD button to select the AUX IN connection.

3). Use the buttons on the external device itself to operate it .

AX IN

U

ollowing the diagram below,

IN socket .

AUX IN

RESET

The RESET button is to be activated for the following reasons: A. Initial installation of the unit when all wiring is completed. B. All the function buttons do not operate. C. Error symbol on the display.

Hea phon s port

de

-16-

Control Panel

UNIT KEYS

11 10

OPEN

VOL-

VOL+

USB IN

IR

PUSH SEL

1

2

12 13 14 15

18

AUX IN

MODE

3

TA/AF

4 5 6

/CH1~6

BND

MU/PTY

9 8

7

17 16

1. OPEN or BUTTON

To slide the monitor out and stand it up or into the monitor slot, press this button;

To adjust the angle of the monitor, long press this button .

2. VOL & SEL

In normal mode, knob is used to increase or decrease the volume.

KNOB BUTTON

VOL

Briefly press SEL button repeatedly to switch between BASS,TRE,BAL,FADE, COLOR,BRIGHT,CONTR, TINT and VOL; Long press SEL button to switch REG, then briefly press SEL button repeatedly to switch between PI, TA, AF, LOUD,SWF, EQ,DX/LOCAL(in radio mode),STEREO/MONO(in radio mode), TIME

24H/12H, SET CLOCK, BUZZ,EUR/USA FREQ, ANIMA,BG and LED;

After switching a desired item above, rotate VOL knob to set.

3. (POWER On/O ff )/MODE

Press it to turn on the unit, to switch the device off. In playback mode, Press it repeatedly to select RADIO, DISC, USB, CARD and AUX IN mode.

Press and hold for two seconds

-17-

Control Panel

4/10. |<< and >>| BUTTONS

In radio mode, Long pressing |<< or >>| button can automatically search down or up

for an available station beginning from the current frequency; Briefly pressing |<< or >>| button can manually search down or up for the current frequency.

In media mode, pressing |<< or >>| button can play previous or next track; conti nuously and long pressing |<< or >>| button can fast backwards or forwards at the

following multiple of normal speed: x2, x4, x8, x20, x1.

5. TA/AF BUTTON

TA Function [traffic Announcement] Button(for Rds Only)

In RADIO mode When you swing briefly the MU/PTY knob in the direction of the TA/A F button , the TA function is activated, the TA symbol appears in the display . (swing

AF [Alternative Frequencies] Swing and hold (more than 2’s) the MU/PTY knob in the TA/ AF direction , the AF function is activated. The AF symbol appears in the display . (swing and hold it

again to cancel this function .) The function about RDS to see page 23 . Note: In Radio mode, press and hold the SEL knob for a long time to access the selection menu: REG ON/REG OFF, PI MUTE/PI SOUND, AF ON/AF Repeatedly pressing the SEL knob to select the item and by using the VOL+/- to change .

it again to turn off . )

a your desired station beginning from

OFF .

6. BAND BUT TON

In Radio mode, press it repeatedly to select the desired radio band: FM1, FM2, Fm3, AM1(MW1), AM2(MW2) .

7. MU/PTY BUTTON

Press it button to switch of the loudspeakers for a short period. The word MUTE flashes in the display. Press it again to cancel the mute function. This function can also be cancelled by rotating the VOL multifunction button. In

Radio Mode, press this button and hold for a bout 2 seconds to select the PYT

of the grogram type (examples of such types of program are : NEWS, POP.....)

8 /CH 1-6 (R ADIO PRESET) BUT TON

A) In Disc Playback Mode Press this button to pause playback, press it again to resume playback.

B) In Radio Mode Press this button repeatedly to preset station. With this system a total stations can be stored in the memory . Each band store up to six preset stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2 (MW2) band.

-18-

of 30

Control Panel

Follow the instructions below:

-Store in Memory > Select the frequency band > Press repeatedly the button to select the desired memory key .

> Select the station > Keep the desired memory key after a brief interruption .

- Retrieve a preset station press the button repeatedly to retrieve a station which had been stored in the memory in

advance the chose number is shown on display .

9. REL BUTTON

Press it to detach the control panel.

11 (EJECT) BUTTON

Insert the disc, label side facing up, until the mechanism senses its presence and draws the disc in. Press it to eject the disc.

pressed in until the station is heard again

12. IR sensor

13. USB PORT

14. AUX IN JACK

15. LCD Display Screen

16. SD C ARD SLOT

17. RESET BUT TON

Press this button to return to factory settings.

-19-

Touch Screen Operation

87.50

FM1

MHZ

DX

ST

USER

1 2

388.50 90.00

98.00

65

4

80.50

103.00

106.00

RADIO OPERATION

Listening to radio

Touch the RADIO ICON in home menu to enter the RADIO mode:

87.50

103.00

106.00

Selecting The Frequency Band

Touch the screen of “ BAND ” section repeatedly to select the band , the message will show in turn :

FM1 FM2 FM3

AM2(MW2)

MHZ

USER

DX

98.00

80.50

AM1(MW1)

Start Searching For a Station

Manual Search

During Radio mode, briefly touch “ ” to increase frequency by one step of channel spacing. Briefly touch “ ” to decrease frequency by one step of channel spacing.

Automatic Search

During Radio mode, touch and hold (for more than 2 seconds ) either “

/ ”

ICONS to start search for a radio station automatically.

To tune in strong-singnal FM Station only (LO/DX function)

In home menu, then touch the “ SET ” icon to enter the setting menu, the message will display as below :

RADIO LOC/DX

DX

When an FM stereo broadcast is hard to receive

Press ST/MO button on the remote control to select the MONO or STEREO mode . (When Stereo mode is activated, the ST symbol will appear . )

Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.

Tou c h the “ SOUND ” section on the setting menu, touch the “ / ” ranges to select the “ Radio L/D ” item, touch the “ / ” ranges to choose between the LOC and DX mode of Local and distance traffic news .

-20-

Long-

Touch Screen Operation

87.50

FM1

MHZ

DX

ST

USER

1 2

3

88.50

90.00 98.00

65

4

80.50

103.00106.00

87.50

FM1

MHZ

DX

ST

USER

1 2

3

88.50

90.00

98.00

65

4

80.50

103.00106.00

Storing and Listening to a Memory station

Setting Memory

MHZ

USER

DX

88.50

90.00

103.00

With this system, a total of 30 stations can be stored in the memory of six buttons. Each band stores up to six preset stations. The stations might be FM1, FM2, FM3, AM1(MW1), and AM2(MW2) band. The operation is as below :

- Store in Memory >Select the frequency band

> Select the station > Keep the desired memory key pressed in until the station is heard again after

a brief interruption .

- Retrieve a preset station Touch the 1-6 ranges briefly to retrieve

a station which had been stored in the memory in advance the chose number is shown on display .

Automatic Preset Setup

In Radio Mode, touch and keep (for more than 2 ’ S) the screen of “ APS ” range to active automatic station storage. The radio searches within the current frequency band, e.g. FM1, for the stron ger signal level until the search

cycle has finished . The six strongest stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set .

Scan Function

In Radio mode, briefly touch the “APS” section on the touch screen , the radio briefly plays all the preset stations of the frequency band .

RDS FUNCTION

In Radio mode, touch the “RADIO” ICON to enter the main menu, then touch the “ SET ” ICON to enter the set mode, the message in the display : (only in the “TA ON” mode. )

REGION

PI SOUND

ON

Automatic Memory Storing & Program Scanning

MHZ

USER

DX

88.50

90.00

98.00

80.50

103.00

Note: the RDS icon displays only when setting EUR FREQ and power off the unit and then power on again.

Tou c h the “ RDS ” section on the setting menu, touch the “ / ” ranges to select the adjustment item, touch the “ / ” ranges to adjust the selectment item , It`s depend on your need to select the different

function . Then touch the “SET” range to return to the previous playback .

-21-

Touch Screen Operation

ADJUSTABLE ITEMS:

REGION SET

Touch to switch the REGION function ON and OFF .

PI SET

Touch to change between PI MUTE and PI SOUND .

REG FUNC TION

at certain times some stations divide up their programs with varying content . REG ON : the message “REG ON” will appears in the display for a few seconds . Note :

- the display capacity is limited . It is possible that in the double display mode some segments of the display are deleted .

- the function REG radio from switching to alternative frequency which have a diferent regional program content . REG OFF : the program identification (PI) of the regional program is ignored during the search for an alternative frequency (AF) or a program identification (PI) .

PI MUTE / PI SOUND

(only for radio operation)

if you are in an area where two program identifications (PI) overlap, you can select the option PI SOUND and PI MUTE for playback of the sound. Alternate switching of the program identification should be avoided .

PI SOUND : if switching nevertheless occurs the sound of another station is heard for less than one second .

PI MUTE : the sound of another station is suppressed .

into regional programs

ON prevents the

TA Traffic Announcement

(Priority For Traffic Information)

In Radio mode, touch the cursor button to switch the TA function ON and OFF .

When the TA function is activated, the TA symbol appears in the display . During radio operation in one FM frequency band the search for a traffic announcement station is started automatically (TA SEEK) . If an

FM station is being received which transmits the latest traffic announcements from time to time, the TP display lights up.

When the TA function is switched on , the FM traffic automatically interrupt CD operation (the word TRAFFIC appears in the display).

The volume level is increased to the minimum traffic announcements.

After the traffic announcements has finished, the program that was previously running is resumed.

Interruption of the TA Function: if you would like to interrupt the current traffic announcement, touch the TA section on screen briefly . This does switch off the TA mode .

value for the transmission of

AF FUNCTION

(Alternative Frequencies)

In Radio mode, touch the cursor button to switch the AF function ON and OFF .

AF is a function that works with the help of RDS (Radio Data System) and can only be used with FM stations . The radio searches in the background for the best frequency reception of the has been tuned into .

station that

-22-

Touch Screen Operation

Touch the AF section on touch screen or swing and keep the SEL knob in the TA/A F direction for about 2 seconds , the AF function is activated. The AF symbol appears in the display .

When the AF function has been switched on, the radio continuously tests the signal strength The test interval for each AF frequency depends on the signal strength of the

current station and varies from a few minutes in the case of weak signals. Whenever the new AF frequency is stronger than the station that is currently tuned in , the radio switched frequency for a short time for a short time and the message “NEW FREQUENCY “ is displayed for one or two seconds.

Note :

the status of the AF function is shown by

an AF symbol in the display.

If the AF symbol

the AF function is switched on and RDS

transmission date is being received .

If the AF symbol flashes in the display, the AF function is selected but no RDS signal can be received at the moment .

of the AF frequency .

to this

appears in the display,

With PTY function you can specifically select stations transmitting a particular type of program. Touc h the PTY range on screen repeatedly to call up the PTY selection menu . The message “PTY SEEK” then appears briefly in the

display .

When PTY has been selected the radio starts searching for corresponding PTY information and stops when the PTY information has been found, “NO PTY” appears in the display. If the PTY information being searched for no longer exists, switches to normal mode .

the PTY function automatically

PTY FUNCTION

In Radio mode, touch screen of “PTY” range to select the Program type .

PTY Selection of the program type besides the stations name, stations also transmit information on the type of program. This information can be displayed by your car radio .

Examples of such types of program are :

SPORT NEWS POP WEATHER ......

some FM

-23-

Touch Screen Operation

TITLE

PBC

MENU

MEDIA OPERATION

In any mode, press the MODE on the front pane (or touch the DISC icon on the home menu)to enter the DISC play mode . The message will display as below : (When Parking Brake supplied .)

Mute function

To decrease the volume level

To increase the volume level

To enter the main menu

To skip the previous track

To search the disc with numbers

To display the root menu on stored

MENU

Digital Video discs .

In Digital Video mode, touch to

TITLE

display the title menu. In VCD mode,

PBC

touch to switch PBC ON and PBC OFF.

To show/hide the Subtitle (depending on the used media)

To change the AUDIO setting (depending on the used media)

ZOOM IN and OUT

Turning pre-switching for traffic announcements on and off

Random Function

Repeat Function

Intro Function

Next menu

To search fast forward

To search fast backward

Stop

Play/Pause the disc

To skip the next track

Switching on and off an Alternative frequency

To display the SETUP menu

To select the Equalizer mode

On screen- display

To show / hide the clock

Loudness Function

Subwoofer Function

Previous menu

-24-

Touch Screen Operation

BASIC OPERATION

Stopping Play

Touch ICON to stop the unit playback. Touc h to start play.

Pause (still picture)

Touch during playback to temporarily pause play. Tou c h again to return to normal playback.

Rapid Forward/Rapid Reverse

During DISC playback, touch / for rapid forward/reverse.

The speed of rapid forward/ reverse changes according to the disc as follows:

Digital Video/VCD/CD/MP3:

Normal Playback 2x 4x 8x 20x

Skipping Track

During DISC playback, touch / to skip to next/back one track.

Note:

when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right .

SELECTING PLAY MODES

During the Disc playback, touch the “RPT, RDM, INT ” range to select the different playing mode .

1). REPEAT FUNCTION

FOR Digital Video :

Tou c h the screen of the “RPT” range (or press the REPEAT button on the remote control) to select REPEAT mode as follows :

CHAPTER REPEAT ON TITLE REPEAT ON

REPEAT OFF

FOR VCD/CD :

Touch the screen of the “RPT” range (or press the REPEAT button on the remote control) to select REPEAT mode as follows :

REPEAT ONE REPEAT ALL

REPEAT ALL

REPEAT OFF

Note :

For some VCD2.0 disc (PBC-playback

control), above these buttons may be

unavailable.

Zoom Function

Repeatedly touch for zoom-in/ zoom-out rates as follows:

“zoom 2, zoom 3, zoom 4 , zoom ½,

Use the direction keys ( / / / on remote control to move the enlarged picture.

zoom 1/3, zoom 1/4 , zoom off . ”

FOR MP3 :

Tou c h the screen of the “RPT” range (or press the REPEAT button on the remote control) to select REPEAT mode as follows :

REPEAT ONE REPEAT FO LD ER( or DIR)

REPEAT OFF

REPEAT ALL

2). INTRO FUNCTION

FOR

CD :

Tou c h the screen of the “INT” section (or longer press the 3/INT button on the remote control ) to play the previous 10

-25-

Touch Screen Operation

seconds part of each track/chapter on disc. (Touch it again to cancel this mode)

FOR VCD :

Touch the screen (or longer press the 3/INT button on the remote control ). It display will following menu as below :

SEQ PLAY IN RO 1

Note: when select the INRO Mode, this

player to start to play the previous 10

seconds part of each track/chapter on

disc. (Touch it again to cancel

this mode .)

FOR Digital Video/MP3 :

For Digital Video/MP3 , press the INT

button is not available .

of the “INT” section

3). RDM(RANDOM) FUNCTION

During DISC playback, touch screen of

“RANDOM” section ( press the 4/RDM

button longer on the remote control to

play in random. Each playing, the order

is different . (Depend on the disc used

for VCD).

Touch it again to cancel this function .

Note : in random mode, the button is

not available .

DISC Search (GOTO)

FOR Digital Video :

Tou c h the screen the of “GOTO” range the screen will display the following message :

Digital Video TT 01/01 CH 03/31 0:01:44

Touch the / to select the your adjustment item, then select the item you want to watch through CHAPTER/ TIME setting by touching the numberic buttons , then touch the ENTER button to confirm .

FOR VCD (With PBC OFF):

Tou c h the screen the of “GOTO” range , the screen will display the following message :

VCD TRK 01/19 PBC 0:01:44

A

4). TO P FUNCTION

ForDigital Video/ VCD/CD/MP3:

In the state of Digital Video/VCD/CD/

MP3 disc playing, press the 1/TOP

button on the remote control to select

the first track/chapter to play.(depend

on the disc used for VCD)

Tou c h the / to select the your adjustment item, then select the item you want to watch through TRACK/TIME setting by touching the numberic buttons , then touch the ENTER button to confirm .

-26-

Touch Screen Operation

ON-SCREEN DISPLAY FUNCTION

OSD

1. Digital Video:

A.Touch or Press OSD for first time:

Digital Video TT 01/01CH 04/31 C 0:02:06

Tit l e Number, To t al Titl e Number,

Chapter Number, To t a l Chapter Number

of this Title of the disc currently being

played will be shown on the screen,

along with the elapsed time.

B.Touch or Press OSD for second time:

½ ENG 2CH OFF AN OFF

The underlined part is different from

the used discs. The AN is a camera

figure for some models.

C.Touch or Press OSD for third time:

Digital Video TT 01/01CH 04/31 C -0:01:32

During playback, touch the screen of the OSD section, it will display the following as below :

2.Example for VCD/SVCD/CD:

A.Touch or Press OSD for first time:

VCD TRK 1/19 PBC C 0:01:36

A

B.Touch or Press OSD for second time:

VCD TRK 1/19 PBC C -0:06:06

A

C.Touch or Press OSD for third time:

VCD TRK 1/19 PBC T 0:02:12

A

D.Touch or Press OSD for fourth time:

VCD TRK 1/19 PBC T -1:23:06

A

E.Touch or Press OSD for the fifth time: The message on the screen will be cleared for SVCD and VCD.

NOTE:

For CD(audio) Disc, touch OSD button is not available .

D.Touch or Press OSD for fourth time:

Digital Video TT 01/01CH 04/31 T 0:16:00

E.Touch or Press OSD for fifth time:

Digital Video TT 01/01CH 04/31 T -1:36:55

F. Touch or Press OSD for sixth time:

The message on the screen will be

cleared.

3. Example for MP3

A.Touch or Press OSD for first time:

CDrom TRK 2/76 C 0:00:36

A

B.Touch or Press OSD for second time:

CDrom TRK 2/76 C -0:03:38

A

C. Touch or Press OSD for third time: The message on the screen will be cleared.

-27-

Touch Screen Operation

Digital Video Special Function

1. Multi-subtitle Language

Function (for Digital Video Only)

During Digital Touch the SUBTITLE section on touch screen(or press the SUBTITLE on the remote) .

Each time the button is pressed or touch, number of the subtitle language changes in sequential order.

Notes:

- The language number is different

according to the disc.

- Some discs only contain one subtitle

language.

- When no different subtitle language

are recorded, “ INVALID KEY ” will be

displayed at screen left top corner.

Video playback.

2. Multi-Audio Language Function

For Digital Video:

During Digital Video playback , touch the AUDIO section on touch screen (or press the AUDIO

on the remote .) Each time the button is

pressed or touch , number of the audio

soundtrack language changes on

sequential order.

Notes:

- The language number is different

according

- Some disc only contain one language

soundtrack

- When no different language soundtra-

ck are recorded will be

display at screen left top corner.

For VCD/CD:

during playback, touch the AUDIO

section of the touch screen or Press

AUDIO on the remote . It is possible to

switch the sound between monaural

and stereo sound.

MONO LEFT MONO RIGHT

to the disc.

“ INVALID KEY ”

MIX-MONO

STEREO

3. Title Menu Function

For Digital Video:

If the Digital Video has multiple titles recorded on the disc. It can select preferred title from the title menu to start playback.

- During Digital Vid eo playback, press TITLE button on the remote .The title menu is display.

- Select preferred title by the button and confirmed by press the ENTER button .

For VCD:

Press TITLE/PBC button on the remote control while the disc is playing, you can switch between "PBC ON"and "PBC off" mode.

cursor

-28-

Touch Screen Operation

MEDIA SETUP MENU

USING THE MENU

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

EXIT

1. Touch the screen of “ ” range or press the SETUP button on remote .

2.The SETUP menu is displayed.

3.Touch directly the desired item to select the preferred item . Or by using the / / /

4. Touch the EXIT section to clear the setup menu or press the SETUP on the remote control .

Overview Of The Main Menu

(1)(2)(3)(4)

(1). System Settings

(2). Language Settings

(3). Video S ettings

(4). Digital Settings

buttons .

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

EXIT

TV TYPE SETUP

This player is capable of playing discs recorded in either PAL or NTSC formats. Make the selection based on whether you are connecting the unit to a PA L TV or an NTSC TV. You can also set the unit to AUTO (autoselect). The disadvantage to autoselect is that

each time you turn the unit on it checks to see what kind of monitor is connected, which causes a small delay and some flickering of the display image which you may find unpleasant.

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

EXIT

SCREEN SAVER SETUP

If the screen displays a static image for too long, some "burn-in" may occur, leaving

a permanent trace of the image behind. To avoid this, turn ON the SCREENSAVER item. After a short period of inactivity on the monitor, the unit will substitute a moving image to avoid burn-in.

NTSC

PAL AUTO

ON

OFF

-29-

Touch Screen Operation

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

EXIT

16:9

4:3PS

4:3LB

16:9

4:3 Letter Box

4:3 Pa n Scan

TV DISPLAY SETUP

This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set. Normal/PS (For 4:3 TV) Played back in the PAN & SCAN style. (If connected to wide-screen TV, the

left and right edges are cut off.) Normal/LB (For 4:3 TV) Played back in LETTER BOX style. (If connected to wide-screen TV, black bands appear at top and bottom of the screen.) Wide (For 16:9 TV) Select when

a wide-screen TV set is

connected.

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

-----

EXIT

PASSWORD SELECTION

The password must be used to make changes to the Parental Control menu below . The factory default password is

0000. Yo u will be asked for the current password. Key in “0000” and then press “ENTER” on remote control to confirm .

you have the opportunity to change it and enter your new password . Then when you enter the Parental Control menu, you can make any changes.

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PAS S WO R D RATING DEFAULT

EXIT

1 KID SAFE 2 G 3 PG 4 PG13 5 PG-R 6 R 7 NC-17

8 ADULT

RATING

Select suitable parental guidance with the cursor buttons and confirm it by pressing the ENTER button.

-30-

Touch Screen Operation

SYSTEM SETUP

TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT

RESTORE

EXIT

DEFAULTS

Selecting the DEFAULT item and confirming RESTORE will return ALL personal settings you have made, including radio and TV presets, to the factory default settings.

LANGUAGE SETUP

OSD LANGUAGE AUDI O LANG SUBTITLE LANG MENU LANG

EXIT

ENGLISH

GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN

LANGUAGE SETUP

OSD LANGUAGE AUDI O LANG SUBTITLE LANG MENU LANG

ENGLISH

GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN

EXIT

AUDIO LANGUAGE SETUP

Select the preferred AUDIO soundtrack language by touching directly the desired language .

LANGUAGE SETUP

OSD LANGUAGE AUDI O LANG SUBTITLE LANG MENU LANG

EXIT

ENGLISH

GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN OFF

OSD LANGUAGE SETUP

Select the preferred OSD language by touching directly the desired language .

SUBTITLE LANGUAGE SETUP

Select the preferred Subtitle language

by touching directly the desired

language .

-31-

Touch Screen Operation

LANGUAGE SETUP

OSD LANGUAGE AUDI O LANG SUBTITLE LANG MENU LANG

ENGLISH

GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN

EXIT

DISC MENU LANGUAGE SETUP

Select the preferred DISC MENU langu age by touching directly the desired language .

VIDEO SETUP

these settings allow you to set the video signal brightness, contrast, hue, and saturation .

VIDEO SETUP

BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS

12 10

8 6 4 2 0

VIDEO SETUP

BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS

12 10

8 6 4 2 0

EXIT

CONTRAST- the contrast of the video signal (the dark portions of pictures).

VIDEO SETUP

BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS

+6 +4 +2

0

- 2

- 4

- 6

EXIT

HUE- the hue of the video signal (the color of the pictures)

.

EXIT

BRIGHTNESS- the brightness of the video signal (how light the picture is) .

-32-

Touch Screen Operation

DIGITAL SETUP

VIDEO SETUP

BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS

12 10

8 6 4 2 0

EXIT

SATURATION- the saturation of the video signal (the vividness of the color) all above can be adjusted to your tasters .

VIDEO SETUP

BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS

EXIT

8 6 4 2 0

DI GI TAL SETUP

FULL

DYNAM I C RANGE

6/8 4/8 2/8

OFF

EXIT

DYNAMIC RANGE CONTROL

Select DRC and adjust the dynamic range of a Dolby Digital encoded program. There are 8 steps between full compression and off compression.

SHARPNESS- the sharpness of the video signal (the image setting acumination) .

-33-

Touch Screen Operation

AUX Operation

On the front panel of this unit, there is an AUX IN jack, follow the diagram below to connect analogue replay devices(only for the Audio connect, if you want to connect the Video, please plug the <Video input > on the back of the unit .) . Use this jack to replay sound of other replay equipment such as media players, computers, etc. Via the loudspeakers.

1). Please connect the external device with stereo jack plug the Aux in socket .

AUX IN JACK FRONT PANE L

RCA

3). You now hear the sound from the external device played back through the loudspeakers .

AUX IN

Ground

Right

Left

Note:

the unit is only support the 3.5 mm A/V Jack Pin Assignment shown as the diagram .

2). In any mode, press the “MOD” button on the front panel to select AUX mode .

4). Touc h the volume+/- sections on touch screen or use the VOL+/- on the panel to adjust the volume level.

-34-

Touch Screen Operation

USB Operation

Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically.

USB IN

IN USB PLAYBACK MODE

User can use your finger directly to touch the desired track to start play .

Yo u can use the UP, DOWN, RIGHT or LEFT buttons files to play, and press ENTER to begin playback (or viewing, in the case of JPEG files).

To skip to the next or last track, touch or press the or . Press the or buttons for Fast Forward or Fast Reverse playback.

REPEAT play modes are also available by repeatedly long pressing the 2/RPT button until the desired mode is found.

to navigate and to select

Changing From DISC to USB Playback Mode

If the disc present in the player is an DISC or VCD or MP3/WMA or MP4 disc, touch the screen of the “ ” range to enter “USB” ICON to enter the USB mode .

IMPORTANT NOTE:

To prevent damage to the USB device, do not remove or disconnect it during playback. it is also a good practice to remove the USB drive during disc playback.

the home menu, then touch the

Changing From USB to DISC Playback modes

If you are in USB Playback mode and wish to begin in the player, touch the screen of the “ ” range to enter the home menu,

then touch the “ DISC ” ICON to enter the DISC mode .

playback of a disc already

-35-

Other Main Operation

SD/MMC card OPER ATION

The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card .

INSERTING THE SD OR MMC CARD .

Label side facing upward

Insert the memory card

Press REL button to detachable the panel

Press in till heard a “CLICK”

REMOVING THE SD OR MMC CARD .

into slot with label side facing upward . Note: the mini card slot for GPS only.

Mode change to SD/MMC card

After a SD or MMC card was inserted into the main unit card slot . the unit will starts playing the files contained on the memory card . Once the unit read the memory card successfully, the first file on the memory card will automatically start playback. Press the MODE button

Change DISC to SD/MMC card

The operations are same as USB mode, refer to see USB operation .

Change SD/MMC card to DISC

The operations are same as USB mode, refer to see USB operation .

File Playback Operation

All the SD or MMC memory car playback operation function is same as the operation on CD/MP3/WMA . Please to “ MP3/WMA” operation for more details .

Remove the memory card Press in till heard a “CLICK”

repeatedly is allowing changing to other modes .

-36-

Touch Screen Operation

WMA

Mp3

[MP3]

ITLE / SONG: TRACK 03 /

001

002

003

004

005

006

007

008

007

001

002

003

MP3/WMA/JPEG/MPEG4 PLAY

The unit is support MP3/WMA/JPEG/MPEG4 . When a disc is inserted into player, the following picture will appear on the monitor . The unit will play the first track automatically . Yo u can touch to directly others mode (MP3/JPEG /MPEG4) to play . EX. : when the MP3 mode is selected

2

ITLE / SONG: TRACK 03 /

1

.

1 Current type

(highlighted bar) .

2 Current track (ID3 TAG display) .

3 The current play mode(MP3).

007

4 Select the play mode(JPEG).

5 Select the play mode(MPEG4).

Touch directly to select the play mode and then touch the desired track to play . Or Use / / / on the remote control to select the play press ENTER button on the remote control to confirm.

MOVING TO ANOTHER TRACK :

1. Touch directly the desired song to start play .

3 4 5 6

6 Current song in MP3 folder .

mode or item, then

2. Touch the or range on the touch screen to skip a track ahead or back.

3. Press the or button on the remote control to skip a track ahead or back.

FAST FORWARD/FAST BACKWARD

1. Touch briefly the “ / ” range on touch screen for fast forward / fast backward.

2. Press shortly the or button on the remote control for forward or backward .

REPEAT FUNCTION

Touch the screen of “REPEAT ” range or press longer “REPEAT” on the remote control repeatedly can

select two kinds of repeat play mode.

REP-ONE:

Play the same song over and over again.

REP ALL:

Play all songs on the disc, then repeats the entire disc over and over again .

NOTE:

in JPEG/MPEG4 mode, the details operations as same as MP3/WMA operation .

-37-

Specification

Generall :

Supply Voltage: 12V DC (11V-15V) Current Consumption: Less than10 A Signal System: Compositive video 1.0Vp-p 75 Discs Played: 5"(12 cm) single-sided, single-layer

(2)Compact Disc (CD-DA, VIDEO CD)

Audio Signal Output: 2ch&4ch line out Characteristics: (1)Frequency Response 20 Hz - 20 KHz

(2)S/N Ratio 90 dB (JIS)

5"(12c m) disc

(3)Wow and Flutter Below measurable limits

(1)DIGITAL-VIDEO Disc

5"(12 cm) single-sided, double-layer

RADIO Section:

For 2 Bands For 2 Bands

(Europe) (U.S.A.)

Frequency Coverage: 87.5 to108 MHz 87.5 IF: 10.7 MHz 10.7 MHz Sensitivity (S/N = 30 dB): 15 dBu MW Frequency Coverage: 522 to1620 KHz 530 to1710 KHz IF: Sensitivity (S/N = 20 dB): 40 dBu 40 dBu

FM FM

to107.9 MHz

15dBu

AM

450 KHz 450 KHz

TFT Monitor:

Monitor Screen Size: 7 Inch Wide Color System: NTSC/PAL

NOTE:

Specifications and design are subject to modification, without notice, due to improvements in technology.

-38-

Troubleshooting

Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer.

SYMPTOM CAUSE SOLUTION

If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC"

Replace the fuse

Remove the then put a new one

Insert the compact disc with the label facing upward

Clean the disc or try to play a new one

Cool off or until the ambient temperature return to normal

Please switch to correct color system from menu

Make proper connection according to wire connection

For safety reasons no video/ images are displayed while the vehicle is moving. Engaging the parking brake will cause images to be displayed.

Please choose a proper color system.

Change the disc

Change the disc Record JPEG files using a compliant application

Press the RESET button. Front panel is not properly fixed into its place

Insert the antenna cable firmly

Select a station manually

disc in the player,

“”

No power

Disc can not be loaded or ejected

Video/image appears black-white

No video/image appears

No color in picture

JPEG disc can not be played back

The operation keys do not work

The radio does not work

The car ignition switch is not on

The fuse is blown

Presence of disc inside the player.

Inserting the disc in reverse direction

The disc is extremely dirty or defective

Temperature inside the car is too high

The color system is set incorrectly

The unit is not connected to the parking brake detection switch

The parking brake is not engaged

The disc format is not according to the TV-set used (PAL/NTSC)

No JPEG files are recorded on the disc.

JPEG files are not recorded in a compliant formant

The built-in microcomputer is

not operating properly

due to noise The antenna cable is not

connected

The signals are too weak

MADE IN CHINA

88-J8300-02D

-39-