Pyle PLTLD16 User guide

NTSC, ATSC

PLTLD16

15.6’’ LED RV Digital TV

FHD Flat Screen TV with DVD Combo

with Digital Antenna and 12V/24V Car Adapter

CONTENTS

SAFETY INFORMATION

PRODUCT INTRODUCTION

CONNECTIONS

REMOTE CONTROL

SETUP WIZARD

SELECT INPUT SOURCE

MAIN MENU

PICTURE MENU

SOUND MENU

3

5

6

7

8

9

9

10

11

TIME MENU

SETUP MENU

CLOSE CAPTION

LOCK MENU

CHANNEL MENU

PC MENU

DVD OPERATION

SPECIFICATION

13

14

15

16

18

19

20

24

www.PyleUSA.com

2

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS- READ CAREFULLY BEFORE USE.

Take note of the following safety information which appears on the back of the TV.

CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVER SCREWS.
NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that there are important operating maintenance instructions
in the literature accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.

KEEP THESE INSTRUCTIONS

• Do not use this TV near water.

• Clean only with a slightly damp cloth.

• Do not block any ventilation openings.

• Install in accordance with the supplied Quick Start Guide and this User Guide.

• Protect the power chord from being walked on or pinched, particularly at plugs,and the point where it

exits from the TV.

• Do not allow the power chord to overhang the edge of a table.

• Unplug this TV during lightening storms or when unused for long periods oftime.

WARNING!

TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS TV TO RAIN OR
MOISTURE. THE TV MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS
FILLED WITH LIQUIDS SHOULD BE PLACED ON THE TV.

NOTE: No naked ames such as candles should be placed on the TV.

www.PyleUSA.com

3

SAFETY INFORMATION

This unit has been produced according to aII current safety regulations. The following safety tips

should safeguard users against careless use and the dangers.

• Although this appliance has been carefully manufactured and rigorously checked prior leaving the

factory, as with all electrical appliances it is possible for problems to develop. If you notice smoke, an
excessive build up of heat or any other unexpected phenomena, you should disconnect the plug from
the mains power socket immediately.

• Ensure that the unit is suciently ventilated! Never place next to or underneath curtains!

• The mains plug or appliance coupler is used as the disconnect device, the disconnect device shall

remain readily operable.

• This set should only be connected to a mains power supply which matches that stated on the Iabel on

the rear of theTV- do not attempt to connect it to any other type of supply.

• The socket -outlet must be installed near the equipment and easily accessible.

• To prevent overload, don't share the same mains supply socket with too many other items of equipment.

• Apparatus with Class 1 construction shall be connected to a mains socket outlet with a protective

earthing connection.

• Keep away from rodents. Rodents enjoy biting into electric exes.

• Always hold the plug when pulling out the plug from the mains supply socket.

Do not pull on the ex, the ex can become overloaded and cause short circuit.

• Set up the unit so that no one is able to trip over the ex.

• Do not place heavy items on the ex,which may damage it.

• Take note that the ex cannot be reached and pulled by young children to avoid injury.

• Do not set up the unit near to heat sources.

The casing and the ex could be damaged by the impact of heat.

• The screen is made of plastic and can break if damage is done.

Be careful when collecting sharp edged plastic splinters to avoid injury.

• Avoid placing the unit on any surface that may be subject to vibrations or shocks.

• To protect the unit during a thunderstorm unplug the AC power cable and disconnect the aerial.

Caution: Do not touch the aerial (RF) connector.

• When you leave your home for a long period of time, unplug the AC power cable for safety reasons.

• The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to

prevent overheating. The ventilation holes are not to be blocked. Do not set up near radiators.
Do not place in direct sunshine. When placing on a shelf leave 5cm (2") free space around the whole unit.

• Do not allow water or moisture to enter the TV. Do NOT use in wet or moist areas such as Bathrooms,

steamy kitchens or near swimming pools.

• Do not use this unit when moisture condensation may occur.

• Any repairs must be carried out by qualied personnel only.

• Do not open this unit. A non- expert attempting to repair the unit could be dangerous and potentially

cause a re hazard.

• Liquids spilt into the unit can cause serious damage. Switch the set OFF and disconnect the mains

power supply, then consult a qualied service person before attempting to use the unit again.

www.PyleUSA.com

4

• Do NOT remove the safety covers. There are no useable or serviceable parts inside. You may invalidate

the warranty. Qualied personnel must only service this apparatus.

• Do NOT tap or shake the screen, you may damage the internal circuits. Take good care of the remote

control, do not drop.

• Never place hot objects or open ame sources on or close to the TV.

• High temperatures can melt plastic and lead to res.

• To clean the TV use a soft dry cloth. Do NOT use solvents or petrol based uids. For stubborn stains, you

may use a damp cloth with dilute detergent.

HEADPHONE WARNING

Loud music can damage your hearing irreversibly, therefore do not set the volume to a high level
when listening through headphones, particularly for lengthy listening periods.

WHERE TO INSTALL

Locate the television away from direct sunlight and strong lights, soft indirect lighting is recommended
for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen.
Place the TV on a sturdy platform of which the surface should be at and steady.
This will prevent it from falling over. Make sure the television is located in a position where it cannot be
pushed or hit by objects, as pressure will break or damage the screen, and so that small objects cannot be
inserted into the ventilation slots or openings in the cabinet.

Product Introduction

Front View

The functions of the TV buttons are
described below.

PLAY/PAUSE:

Play/pause the disc playing.

EJECT: Eject the disc.

SOURCE: Press to select the source.

MENU: Press to display the OSD menu,

Press again to exit the menu.

CH+/CH- :
Press to scan through channels. Use to
move down/up in the OSD menu screen.

VOL+/ VOL- : Press to adjust the volume.
Use to move left/right in the OSD menu
screen VOL+ button can be used to skip
forward to next menu.

POWER: Turn on/o the TV set.

LED Indicator Remote Control Window (keep clear)

www.PyleUSA.com

5

CONNECTIONS

1/2. Audio output to connect power amplier stereo equipment.

3. Connect a stereo headphone (3.5mm) for private listening.

4. Connect an optional coaxial digital cable through a compatible amp/receiver to enjoy superior

audio sound.

5/6/7. Connect to an AV device that features component video and audio output jacks.

8. Connect it to the HDMI of DVD or other equipment.

9. Connect an optionalVGA cable from your personal computer.

10. Connect an optional 3.5mm audio cable for sound when using VGA.

11. Connect antenna or cable for television reception.

12. For service technician use only.

13. Connect to the mains adaptor or the car adapter (Input for the 12V/24V power supply)

www.PyleUSA.com

6

REMOTE CONTROL

The remote control is using Infra-Red (IR). Point it towards the front of the LED TV.

The remote control may not work correctly if it is operated out of range or out of angle.

www.PyleUSA.com

7

SET UP WIZARD

STEP 1: Choosing your Picture mode
Use the arrow buttons to select Home Mode standard. Press the ENTER button to complete the step.

STEP 2:

Use the arrow buttons to select Menu Language.
Use the arrow buttons to select English-Francais-Espanol.
Use the arrow buttons to select AIr/Cable.
Select Cable, then press the button to select Cable System. Then press the button to select
Auto-STD-IRC-HRC.

www.PyleUSA.com

8

AUTO SCAN
Press ENTER/ button to start auto scan.

SELECT INPUT SOURCE

MAIN MENU

Press SOURCE button to display the input source list;
Press or SOURCE button to select the input source;
Press ENTER button to enter the input source;
Press EXIT button to quit.

Press MENU to display the main menu or return to the previous menu or close the main menu.
Press to highlight the desired menu icon, and press ENTER to select.

www.PyleUSA.com

9

MAIN MENU OPERATION

Picture Menu

Press MENU to enter the main menu. Press button to select. Press ENTER / to enter.
Press MENU again to exit or back to parent menu.

Press button to select among Picture Mode/Brightness/Contrast/Color/Tint/Sharpness/

Color Temperature/Blue Screen.

Press ENTER / to enter.
Press button to adjust.
Press MENU again or back to parent menu.

PICTURE MENU

Adjust picture mode to change picture appearance.
Press button to select (Standard/Dynamic/Mild/Energy saving/User).

Note: The brightness, contrast, color, tint and sharpness are only available in User mode, you can adjust as

you like.

Standard: Produces a highly dened image in a normally lit room.

Dynamic: Produces a highly dened image in a brightly lit room.

Mild: Produces a highly dened image in a soft lit room.

User: Select to customize picture settings.

Energysaving: Produses a highly dened image in a Energy saving lit room.

[Brightness]

Adjust the visual perception output of the entire picture, it will eect the luminousness of the picture.
Press button to adjust.

[Contrast]

Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.
Press button to adjust.

www.PyleUSA.com

10

[Color]

Adjust the saturation of the color based on your own like. Press button to adjust.

[Tint]

Adjust the hue (Red, Green, Blue) of the picture. Press button to adjust.

[Sharpness]

Adjust the peaking in the detail of the picture. Press button to adjust.

[Color Temperature]

Increase or reduce warm color of the picture personally (red), and the cool color personally (blue)
according to your like.

Normal: The most balanced setting
Warm: Increase the red color for the white.
Cool: Increase the blue tone for the white.

Blue Screen

Press button to select (o/on).

SOUND MENU

Press MENU to enter the main menu, Press button to select.
Press ENTER / to enter.
Press MENU again to exit or back to parent menu.

Press button to select among Soundmode/Bass/Treble/Balance/Surround sound/Auto Volume/
SPDIF type/Accessibility/TV Speaker.
Press ENTER / to enter.
Press button to adjust.
Press MENU again or back to parent menu.

SOUND MODE

Select a sound mode to achieve ideal sound.
Press button to select (Standard/Music/Movie/Sports/User).

Note: The bass and treble are only available in User mode, you can adjust as you like.

www.PyleUSA.com

11

Standard: Produces a balanced sound in all environments.
Music: Preserves the original sound. Good for musical programs.
Movie: Enhances treble and bass for a rich sound experience.
Sports: Enhances vocals for TV audio.
User: Select to customize audio settings.

BASS: Adjust the bass eect. Increases or decreases lower-pitched sounds. Press button to adjust.

TREBLE: Adjust the treble eect. Increases or decreases high-pitched sounds. Press button to adjust.

BALANCE: Adjust the balance between left and right speakers to adapt to your listening position.

Press button to adjust.

SPDIF Type:

Accessibility:

Voice Guide

Press

Volume

Press the sserP. emuloV ot nottub button to select (Middle-Strong-weak)

Speed

Press the button to speed . Press

Pitch

TV Speaker:

Adjust Accessibili ty settings ress ENTER / button to enter.

）

sserP. hctiP ot nottub eht sserP button to select (Middle-Strong-weak).

p

button to sele ct (Middle-Strong-weak).

www.PyleUSA.com

12

is used

TIME MENU

Press MENU to enter the main menu, Press button to select.
Press ENTER / to enter.
Press MENU again to exit or back to parent menu

Press button to select among Sleep Timer/Time Zone/Daylight Saving Time/Time Format/Auto Clock/
Clock.
Press ENTER / to enter.
Press button to adjust.
Press MENU again or back to parent menu.

SLEEP TIMER

Set a timer for the TV to turn o automatically.
Press button to select (O / 5min/10min /15min/ 30min / 60min / 90min / 120min/180min/240min).

TIME ZONE

Select your time zone.
Press button to select (Eastern/Central/Mountain/Pacic/Alaska/Hawaii/Samoa/Newfoundland/Atlantic).

DAYLIGHT SAVING TIME

Set the daylight saving time for your area. Press button to select (On/O).

TIME FORMAT

Select your time format.
Press button to select (12-hour/24-hour).

AUTO CLOCK

Use to synchronize the display automatically. It is only available in DTV.
Press button to select (On/O).

www.PyleUSA.com

13

SETUP MENU

Press MENU to enter the main menu, Press button to select.
Press ENTER / to enter.

Press MENU again to exit or back to parent menu.

Press button to select among Menu Language / Transparent / Zoom Mode/Noise Reduction/
Advanced/Source Label/Closed Caption/DLC/Setup Wizard/Overscan/HDMI CEC/Restore Default/OSD
Timeout.

Press ENTER / to enter.
Press button to adjust.

Press MENU again or back to parent menu.

MENU LANGUAGE

Select an OSD menu language can be displayed. Default English is selected as menu language.
Press button to select language (English / Français / Español).

TRANSPARENT

Adjust the transparency of the OSD (on screen display) menu.
Press button to select (ON/OFF).

ZOOM MODE

Adjust how the picture lls the screen.

Normal Automatically adjust Aspect Ratio based on TV size and TV program.
Wide Use to watch wide screen (16:9) content.
Zoom Expands image to ll screen. Top and bottom maybe cut o.
Cinema Stretches image at edges but keeps a clear image in the center.

www.PyleUSA.com

14

Source Label: Create labels for the devices connected to your TV. Press ENTER / button to enter.

CLOSED CAPTION

Adjust Closed Captioning settings. Only available under TV and AV source.

CC MODE: Turn Closed Captioning on/o. Press button to select (Of/On/CC On Mute).
Basic Selection: Set Closed Captioning for standard (analog) program.

Press button to select (CC1/CC2/CC3/CC4/TEXT1/TEXT2/TEXT3/TEXT4).
Advanced: Set Closed Captioning for digital program.
Press button to select (Of/Service 1/Service 2/Service 3/Service 4/Service 5/Service 6).

OPTION: Adjust the digital Closed Captioning setting. Press button to enter.
MODE: Set the look of digital Closed Captioning. Automatic uses broadcaster's style.

Press button to select (Default/Custom).
FONT STYLE: Select from 8 font styles.
Press button to select (Default/Font 0/Font 1/Font 2/Font 3/Font 4/Font 5/Font 6/Font 7).
FONT SIZE: Adjust the size of the digital Closed Captioning font.
Press button to select (Default/Normal/Large/Small).
FONT EDGE STYLE: Adjust the edge of the digital Closed Captioning box.
Press button to select (Default/None/Raised/Depressed/Uniform/Left Shadow/Right Shadow).
FONT EDGE COLOR: Adjust the color of the digital Closed Captioning box.
Press button to select (Default/Black/White/Red/Green/Blue/Yellow/Magenta/Cyan).
FG COLOR: Adjust the color of the digital Closed Captioning font.
Press button to select (Default/White/Red/Green/Blue/Yellow/Magenta/Cyan).
BG COLOR: Adjust the digital Closed Captioning background color.
Press button to select (Default/Black/Red/Green/Blue/Yellow/Magenta/Cyan).
FG OPACITY: Adjust the transparency of the digital Closed Captioning font.
Press button to select (Default/Solid/Flashing/Translucent/Transparency).
BG OPACITY: Adjust the digital Closed Captioning background transparency.
Press button to select (Default/Solid/Flashing/Translucent/Transparency).

DLC: Automatically adjust picture detail and brightness. Press button to select (O/On).
Setup Wizard: Set the rst time installation.
Overscan: Press button to select (On/O).

It is only available to enter 1080i/720p/1080p in DTV/Component/HDMI. Default is On.
It is xed set to be On in ATV/AV. It is xed set to be O in PC.

HDMI CEC: Press the button to highlight CEC, then press the ENTER / button to enter.
Restore Default: Change power on options or reset TV to factory default. Press ENTER / button to enter.
OSD TIME OUT: Adjust the duration of the OSD (on screen display) menu.

Press button to select (5 Sec.1, 5 Sec., 30 Sec., 45 Sec., 60 Sec.)
Auto sleep: Adjust the time for automatic standby without signal display.
Select the ON mode: When there is no signalinput, the TV will automatically enter the standby state after
about 15 minutes.
Select O mode: The TV will not automatically stand by when there is no signal input.

www.PyleUSA.com

15

LOCK MENU

Press MENU to enter the main menu, Press button to select. Press ENTER / to enter.
Press MENU again to exit or back to parent menu.

Press button to select among Set Password/System Lock/Input Block/US/Canada/RRT Setting/
Reset RRT/Clear LOCK.

Press ENTER / to enter. Press button to adjust.
Press MENU again or back to parent menu.

Enter your 4-digital password. Default password is 0000, if you forgot your password, please call the
service center.

Set Password

Enter a new 4-digital password then re-enter it to conrm. Press button to enter.

SYSTEM LOCK

Lock or unlock the buttons on the TV. Press button to select (O/On).

INPUT BLOCK

Block or unblock the input sources. Press button to enter. Press button to select (Unblock/Block).

www.PyleUSA.com

16

US RATING: Restrict movie and TV programs by US Ratings. Only available when "System Lock" is "ON".
Press button to enter.

CANADA RATING: Restrict movie and TV programs by Canadian Ratings. Only available when "System
Lock" is "ON". Press button to enter.

RRT SETTING: Display an advance V-Chip rating table for digital channels.
The item is available only When current stream has downloadable rating data.

RESET RRT: Reset the RRT to default. The item is available only when current stream has downloadable
rating data

US RATING: For the United States, the rating setting basically include the following options: TV, MPAA.

TV: The TV rating compose of two aspects: age-based and content-based.

Note: The content ratings will increase depending on the level of the age-based rating.

For example, a program with a TV-PG V (violence) rating may contain moderate violence, while a TV-14 V
(violence) rating may contain intense violence. So locking a higher level option will automatically cause
locking the options that has more sensitive level.

www.PyleUSA.com

17

CHANNEL MENU

Favorite/Channel List

www.PyleUSA.com

18

PC MENU

SOURCE

Advanced.

www.PyleUSA.com

19

DVD OPERATION

BASIC OPERATION

· Press the Power button on the TV or the remote control, then press the INPUT button to select DVD mode.

· If there is no disc in the DVD player the screen will show "NO DISC".

· Insert Disc according to picture next to disc slot.

· Do not touch the playing surface.

· Hold the disc around the outside with your ngers and place the disc into the slot.

The player will automatically draw the disc into the player.

· To "Eject" the disc, press the EJECT button on the TV or the " " button on the remote control.

DVD SETUP MODE

· Setup Mode provides the menu forthe conguration of General Setup Page, Audio Setup Page,

Dolby Digital, Setup, Preference Page.

· Item selection in the Setup Menu is done by using the Navigation Arrows, SETUP button and the

OK button.

· Press the SETUP button rst, enter into SETUP menu, then press the DIRECTION RIGHT button, you can

enter into the next Sub-menu.

· Press the SETUP button again to exit the Setup Menu.

GENERAL SET UP

TV DISPLAY

· 4:3 Pan Scan: This is selected when the DVD player is connected to a normal TV.

Wide-screen images are shown on the screen, but with some parts out automatically.

· 4:3 Letter Box: This is selected when the player is connected to a normal TV.

Wide-screen images are shown on the screen, with black belt on the top and bottom.

· Wide: This is selected when the player is connected to a wide-screen TV.

www.PyleUSA.com

20

OSD LANGUAGE

This is used to select the OSD language.

SCREEN SAVER

Start the screen saver, the screen saver image will appear when the player stops or the picture is frozen for
a few minutes. This saver can keep the screen from being damaged.

· ON (Start the screen saver)

· OFF (Remove the screen saver).

LAST MEMORY

Can set the items on the last memory, "ON" and "OFF" option.

Select "ON" the shutdown will shutdown the machine before the settings for memory, re-boot the
machine settings. Set near the same time.

Select "OFF" every time the machine automatically switches back to the default settings

· On (Start the memory)

· O (Remove the memory).

www.PyleUSA.com

21

AUDIO SETUP

• SPEAKER SETUP: In the "Audio Setup page" press " " button to select "Speaker Setup" item, press the
"OK ENTER" or " " button (play) into the "Speaker Setup Page".

DOWNMIX

• LT/RT: A disc recorded multi channel soundtrack. The output signal will be incorporated to left and
right channel

• STEREO: A disc recorded multi channel soundtrack. The output signal will be incorporated to stereo.

PREFERENCE SETUP

www.PyleUSA.com

22

You must press STOP twice to enter Preference Page or NO disc

TV TYPE

• PAL: This is selected when the player is connected to an PAL System TV.

• MULTI: The player will set the TV system according to the disc in the tray.

• NTSC: This is selected when the player is connected to a NTSC System TV.

AUDIO: If a language listed below is recorded on the disc, you can play the sound in such language.
If not, the language recorded will be used.

SUBTITLE: If a language listed below is recorded on the disc, you set the subtitle to be displayed in such
language. If not, the language recorded will be used.

DISC MENU: If a language listed below is recorded on the disc, you can set the Menu to be displayed in
such language. If not, the language recorded will be used.

www.PyleUSA.com

23

SPECIFICATION

1920*1080
3000:1
180cd/m²

16.7M colors
160H,160V

www.PyleUSA.com

24

AC 100V~240V / DC 12V 3A / 24V 1.5A

Questions? Comments?

We are here to help!

Phone: [phone]

Email: [e-mail]