Pyle PLPK-5-TVD-1 Owners manual
PLPK5TVD
OWNER’S MANUAL
COLOUR LCD TV/RECEIVER
INSTALLATION
Notes:
• Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
• Before finally installing the unit, connect the wiring temporarily and make sure it is
all connected up properly and the unit and the system work properly.
• Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
• Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
• Install the unit where it does not get in the driver’s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum
performance.
30˚
• Avoid installing the unit where it would be subject to high temperature, such as from
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,
dirt or excessive vibration.
INSTALLATION HARDWARE
Bracket (A)
(2 pcs)
Hexagonal Bolt
(M6 x 12) (4 pcs)
Tapping Screw
(M5 x 25) (1 pcs)
Bracket (B)
(2 pcs)
Tapping Screw
(M5 x 12) (4 pcs)
Nut
(M5) (1 pcs)
Mounting Bolt
(M5 x 5) (8 pcs)
Plain Washer
(M5) (1 pcs)
2
Double sided
tape (2 pcs)
Mounting Bolt
(M4 x 5) (4 pcs)
Spring Washer
(M5) (5 pcs)
Lever
(2 pcs)
Strap (1 pcs)
Spring Washer
(M6) (4 pcs)
MOUNTING THE TUNER UNIT
2
1
1
2
4
6
5
7
3
6
4
8
5
7
3
7
8
Step 1 Step 2
1. Bracket (A) 5. Tapping Screw with Washer (M5 x 12)
2. Mounting Bolt (M5 x 5) 6. Spring Washer (M6)
3. Bracket (B) 7. Spring Washer (M5)
4. Hexagonal Bolt with Washer (M6 x 12) 8. Double Sided Tape
INSTALL THE DISPLAY UNIT
Before install the display unit, please remove its tail screw and cable parts. This unit
can be properly installed either from “front” (convertional DIN Front-mount) or “rear”
(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit
chassis). For details, refer to the following illustrated installation methods.
6
5
DIN FRONT-MOUNT
Installing the unit
1
182
53
(Fig. 1)
2
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
3
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Display Unit
3
1
6
4
2
3
(Fig. 2)
Removing the unit
1. Dashboard
2. Nut (M5)
3. Spring Washer
4. Tapping Screw with Washer (M5 x 25)
7
5
5. Screw
6. Plain Washer
7. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
1
1. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers upward and out to
makes it possible to remove the unit.
DIN REAR-MOUNT
Installation using the screw holes on the both sides of the unit.
1
2
3
2
5
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw holes
of the bracket and the screw holes of
5
the main unit become aligned (are fitted),
and tighten the screws at 2 places on
each side.
4
Use either truss screws (5 x 6mm) or
screws (4 x 6mm), depending on the
shape of the screw holes in the bracket.
2. Screw
3. Factory Radio Mounting Bracket
4. Dashboard or Console
5. Hook and Screw (Remove this part)
Note: The frame, strap, and half-sleeve are
not used for REAR-MOUNT.
4
HOW TO OPEN AND CLOSE THE SCREEN DISPLAY
1. Press release button to draw out the screen display.
Release Button
2. Turning the display upward.
3. Adjusting the viewing angle. Angle should be adjusted slowly without applying
unreasonable force.
5
4. Turning the display downward. Make sure to return the display to centre position
before drawing in. It cannot be draw in with its angles adjusted.
5. Push the panel, the display will be drawn in.
6
Loading...