Pyle PLMR3DNWT User guide

To ensure correct operation and avoid damage,

please read this user manual carefully before using this product.

INSTALLATION

Installation Procedures

First complete the electrical connections and then check for correctness.

Installation Opening

This unit can be installed in any dashboard having an opening as shown below.

103 mm

182 mm

To Install the Car Radio

Be sure you test all connections rst, and then follow these steps to install this unit.

1. Make sure the ignition is turned o, and then disconnect the cable from the
vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. Attach the “L” brackets (2pcs) on the both sides of the car receiver with screws
(M5.5 x 7) as shown as the below gure. The others xing screws that x the
other terminal of the “L” metal bracket, please buy from your dealer according
to the drilling of holes size.

4. Consult with you nearest dealer if installation requires the drilling of holes or
other modications of the vehicle.

5. Install this car receiver in the dashboard.

6. Make wiring connections, as illustrated in the “Wiring Diagram.”

7. Install the plastic outer trim ring.

www.PyleUSA.com

2

INSTALLATION

Connect all wiring harness and slide the head unit into the mounting collar

until it clicks into place.

Wiring Connections

ANT: Radio Antenna Socket

FL: Front Left Pre-Amp RCA Output (White)

FR: Front Right Pre-Amp RCA Output (Red)

RL: Rear Left Pre-Amp RCA Output (White)

RR: Rear Right Pre-Amp RCA Output (Red)

ACC/ignition (Red)
GND/ground (Black)
ANT/aerial (BLUE)
Power/battery (Yellow)

10A: 10A Fuse

- +12V DC Negative Ground.

- Only use speakers with 4 ohms impedance.

- The maximum current of the Amp remote trigger is 200mA.

www.PyleUSA.com

3

OVERVIEW OF THE CONTROLS

MIC

1. (power)/Volume knob and SEL (select/menu) button

2. SRC (source) button

3. BAND (band) button, (answer call) button

4. AMS (automatic store/preset station scan, automatic music search) button

5. (pause/play), Preset station1 button

6. INT (intro), Preset station 2 button

7. RPT (repeat), Preset station 3 button

8. RDM (random), Preset station 4 button

9. -10 (previous 10 tracks), Preset station 5 button

10. +10 (next 10 tracks), Preset station 6 button

11. CLOCK (clock setting) button, (end call) button

12. (tune down, seek down, previous, fast reverse) button

13. (tune up, seek up, next track, fast forward)button

14. (MUTE) button

15. EQ (Equalizer)

16. IR remote sensor

17. LCD Display

18. USB Port

19. AUX IN (auxiliary input) jack

20. Hands-free Microphone

21. Reset button

www.PyleUSA.com

4

GENERAL OPERATION

Turn Unit ON/OFF, Change the Source

• Press any button to turn on the unit.

• Press the power ( ) button to turn the unit o.

Adjust the volume (VOL)

Rotate the VOL knob on the front panel or press the VOL+ /VOL- button

on the remote control to increase or decrease the volume level.

Adjust Menu Options (SEL)

• Press the SEL button on the front panel or on the remote control repeatedly to

cycle through the following adjustable audio functions: BASS, TREBLE, BALANCE,

FADER, EQ OFF, CLASS/ROCK/POP/ FLAT, LOUD ON/OFF, DX/LOC, STEREO/MONO,

CLOCK 12/24, AREA US/EU, AUTO/BLUE/RED/CYAN/GREEN/PURPLE/YELLOW/WHITE.

• Rotate the VOL knob on the front panel or press the VOL+ /VOL- button

on the remote control to adjust the selected item.

• BASS/TREBLE: -7, -6, ~, -1, 0, +1,~, +6,+7

• BALANCE: L7, L6, ~, L1, 0, R1,~,R6, R7

• FADER: R7, R6,~, R1, 0, F1,~,F6, F7

• EQ (Equalizer) Setting: OFF, CLASS, ROCK, POP, FLAT

• Loudness: LOUD ON/OFF

• DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).

• Stereo/Mono: Switches between MONO and STEREO reception mode for

radio frequencies.

• CLOCK 12/24: Select between 12 hours and 24 hours display.

Note: If 12 hour display is selected , AM= Morning; PM= Afternoon

• AREA US/EU: This car radio is equipped the USA / Europe frequency.

Rotate the volume knob to switch between USA and Europe frequency.

The system will change the frequency setting in about 3 seconds.

• 7 color-changing illumination in buttons:

This car radio device is equipped 7 color-changing illumination in buttons.

The illumination color can be preset Auto (color automatically change one

by one), Blue, Red, Cyan, Green, Purple, Yellow, White.

www.PyleUSA.com

5

Setting the Clock (CLOCK)

1. To display clock time, press the CLOCK button.

2. To set clock time, press and hold the CLOCK button and the hour digits will
ash on the display.

3. Rotate the VOL knob to adjust the hour.

4. Press the CLOCK button again, the minute digits will ash on the display.

5. Rotate the VOL knob to adjust the minute.

6. Press the CLOCK button to conrm time settings.

Change the Source (MODE)

Press the SRC button to switch between RADIO, USB (with USB device inserted),
AUX-IN (auxiliary input) and BT modes.

Mute ON/OFF
In power on mode, briey press the MUTE button to toggle mute on or o.

USB Port

The USB port of this car radio is designed for media playback from ash memory
devices and charging for iPhone/android mobile phone. The USB port also
support USB charging, the charging ability is 5V/1A.

AUX IN (Auxiliary Input) Jack

Reset Button
Push the RESET button with a thin object with a pointed end to reset the unit.

RADIO OPERATION

Switch Between USA area and Europe area Frequency

In radio mode, press the SEL button to enter the switch state of the EU (europe)
and US(USA) frequency, then rotate it to switch between EU and US (USA)
frequency. The system will change the frequency setting in about 3 seconds.

Change Bands

In radio mode, shortly press the BAND button to switch between the FM1 (F1),
FM2 (F2), FM3 (F3), AM1(A1), AM2 (A2) bands.

www.PyleUSA.com

6

To Store/Recall Preset Stations

The radio can be stored 6 preset stations for each band (FM1, FM2, FM3, AM1
and AM2) for atotal of 30 preset stations.

• To memorize a station: Press and hold the desired preset buttons (1-6) to save

a radio station.

• To recall a preset station: Briey press the respective station button (1-6) to

recall the corresponding preset station.

Manual Tuning

In the radio mode:

Press and hold the or button to enter the manual tuning mode.
In manual tuning mode, briey press the or button to search the next or
previous frequency step by step.

Seek Tuning

In radio mode, press the or button, the automatic search will start, it will
search upward or downward for the strong signal radio station within the cuttent
band. The auto searching will stop until nd a station.

Automatic Store Preset station (AMS)

Press and hold the AMS button to store 18 FM and 12 AM preset stations
automatically.

Automatic Preset Scan

Briey press the AMS button to recall each preset station that stored in the
memories in each band.

LOCAL/DX

Press the LOC button on the remote control to choose local or distant reception
mode.

STEREO/MONO

Press the ST button on the remote control to choose FM STEREO or MONO
audio eect.

www.PyleUSA.com

7

USB OPERATION

To insert USB

• Play MP3/WMA music inside a USB stick. Insert the USB stick with MP3/WMA

musics into the USB port, it will play automatically.

• The USB port also support USB charging, the charging ability is 5V/1A.

Select Next Track or Previous Track

In the USB mode, briey press the or button to play the next or previou
track.

Fast Forward/Reverse

Press and hold the or button to fast forward or reverse a track.

Play/Pause

Press the button to interrupt the playback of a music (pause function).
Press this button again to continue the playback.

Introduction Scan

Press the INT button to play the rst 10 seconds of all track.
Press again to stop theintroduction scan, and play the current track.

Repeating the track

Press the RPT button to toggle between RPT ALL (Play all track), RPT ONE
(Continuously repeat current track) and RPT FLR (Continuously repeat all
tracks in current folder).

Playing all tracks in random

Press the RDM button. A random playback of all tracks will start.
Press the button again to set the normal playback.

Track/Folder Navigation

• Press the -10/+10 buttons to jump 10 tracks backward or forward.

• Press and hold the -10/+10 button to select the previous or the next folder.

www.PyleUSA.com

8

Select the track or le for playback in MP3 format

a. Press the AMS button to enter track search mode.
First “TRK0000“ will appear on the display.
b. Rotate the VOL knob to select the number of your favorite track with high
speed.
c. When the desired track number appears, conrm your selection by pressing
SEL button. If no any operation in 5 seconds, it will play the current track.

WIRELESS BT STREAMING OPERATION

Pair and Connect

Before using a Wireless BT device for the rst time, it must be paired and
connected.

1. This head unit broadcasts the pairing signal constantly when no devices are
connected. User can complete the pairing steps from your Wireless BT device.
Refer to owner’s manual for your device for more details.

2. When the phone nds the car audio system, the “Pyle” name will be displayed.
Choose the “Pyle” from the device list to pair and connect with the car audio
system. Upon conrming, the BT logo will stop ashing.

Making a Call

• To make a call, dial the call directly from the paired mobile phone.

• To make a call with this bluetooth handsfree system:

a. When linking up the Wireless BT enabled mobile phone to this BT handsfree
system, press the button to access the dial telephone number mode.
Then press the “0~9”, *and # button on remote control to input the telephone
number, the entered number will be shown on the LCD display.
b. If a number has been incorrectly inputted, press the button or press the
DEL button on the remote cotnrol to delete it.
c. Press the button to make outgoing call.

Answer a Call

When the mobile phone is called, the incoming telephone number displays on
the LCD display. Press the button on front panel or the button on the remote
control to answer the incoming phones.

www.PyleUSA.com

9

Redial Last Dialed Number

Press and hold the button on the front panel or button on the remote
control to redial the last dialed phone number.

Reject or End a Call

Press the button on the front panel or button on the remote control to
reject or end the call.

Switch Audio Between Car Audio and mobile Phone

During a call, press the VOL knob/button to switch the audio source from the car
audio system back to your mobile phone.

Adjust Call Volume

During a talk, use VOL knob or VOL+ /VOL- button to adjust the call
volume level.

Audio Streaming (A2DP)

This head unit supports A2DP (advanced audio distribution prole) wireless
streaming audio from a Wireless BT mobile device directly to your head unit.

The following functions can be used to control the music playback.

• Skip to Next music

Press the button to play the next music in the mobile phone.

• Skip to Previous music

Press the button to previous music in the mobile phone.

• PLAY/PAUSE

Press the button to pause or restore the music playback.

AUXILIARY OPERATION

Using this socket, it is possible to hear the sound of other playback devices
such as MP3 players, CD players etc. through the car loudspeaker.

1. Please connect the external device with a 3.5 mm stereo jack plug to the AUX
socket.

2. Press the MODE button repeatedly until “AUX IN” appears in the display.

3. You hear the playback from the external device via the loudspeakers.
You can adjust the volume of the external device to a comfortable level with
the volume control of this device.

www.PyleUSA.com

10

REMOTE CONTROL

1. (Power on/o) button

2. SEL (Audio/Menu) button

3/15. (Tune down, seek down/ Track

down, Fast reverse) button.

(Tune up, seek up/Track up,

Fast forward) button

4/14. VOL+ (volume increase) button,

VOL- (volume decrease) button

5. MUTE button, DEL (Delete) button

6. INT (intro), Preset station 2, Keypad 2

7. (pause/play), Preset station 1, Keypad 1

8. -10 (previous 10 tracks), previous folder,

Preset station 5, Keypad 5

9. RDM (random), Preset station 4, Keypad 4

10. LOUD (Loudness), Keypad 8

11. STEREO/MONO, Keypad 7

12. MODE button, Keypad *

13. Band button, (answer call) button

16. CLK (Clock setting), (end call) button

17. RPT (repeat), Preset station 3, Keypad 3

18. +10 (next 10 tracks), next folder, Preset station 6, Keypad 6

19. AMS (auto store / preset station scan, auto music search), Keypad 9

20. EQ (Equalizer Preset) , Keypad #0

21. LOC (Local)/DX (Distant) Reception, Keypad #

1
2

3
4

5
6

7
8

9
10
11

12

13
14

15

16

17

18

19
20

21

Note:

When using the remote control for the rst time, you must pull out the portective

plastic tab from the battery compartment found on the back of the remote control.

This product can expose you to a chemical or group of chemicals, which may
include “Di (2-ethylhexyl) phthalate (DEHP)” which is known in the state of
California to cause cancer, birth defects, or other reproductive harm.
For more info, go to https://www.p65warnings.ca.gov/.

www.PyleUSA.com

11

PLR2DN

Stereo Receiver Power Amplier

AM/FM/MP3/BT/USB/AUX, Stereo Receiver, Double DIN, 30 Preset Memory
Stations, LCD Display with Remote Control

Features:

• AM/FM/MP3/BT/USB/AUX Stereo Receiver

• Double DIN

• LCD Display with Remote Control

• AM/FM Stereo Radio, 30 Station Memory

• Wireless BT Audio Ability

• Front Aux-in, Front USB, No SD Card Reader

• Aux (3.5mm) Input Connector Jack

• Connect & Stream Audio from External Devices

• MP3 Digital Audio File Playback

• LCD Display Black Panel

• Electronic Volume Control (Treble, Bass, Balance, Fader)

• Memory/Repeat/Random/Intro Play

• EQ / Mute / Clock Control, English ID3

• ID3 Tag Song Readout for Artist Name/Song Title

• VA LCD/White Back-Light, Night Illumination: RGB

• 2 Pair RCA Output, ISO Connector Line Out

• Equalizer (EQ) Electronic Audio Conguration

• Automatic Memory Preset Store/Scan Mode

• Repeat/Random Song Functions

Technical Specs:

• Remote Control Battery Operated, Requires (1) Coin-Type Battery

• Battery Type: 3V Lithium Bat. 240mAh Capacity

• Night illumination: RGB

• MAX. Power: 4x75W (300 Watts)

• PLL Electronic Tuning Radio Tuner

• ISO with 4 Pin/8 Pin Wire Connector

• Stereo/Mono Mode Selectable

• Audio Control: Treble, Bass, Balance, Fader

• Preset EQ: Flat/Pop/Rock/Class/Jazz/Off

• Switchable USA/Europe Tuner Frequencies by Software

• Max. USB Support: 64GB

• Power: DC 12V

• Current Consumption: 10A

• Product Dimension: 2.7’’ x 7.1’’ x 3.9’’ - inches

www.PyleUSA.com

12

PLMR2DNBK

Marine Stereo Receiver Power Amplier & Speaker Kit

AM/FM/MP3/BT/USB/AUX, Marine Stereo Receiver, Double DIN, 30 Preset
Memory Stations, LCD Display with Remote Control & 1 Pair of PLMR60B

Features:

• AM/FM/MP3/USB/AUX Marine Stereo Receiver

• Black Panel with 1 Pair of PLMR60B

• Double DIN

• LCD Display with Remote Control

• Marine Stereo Receiver System

• AM/FM Stereo Radio, 30 Station Memory

• Wireless BT Audio Ability

• Aux (3.5mm) Input Connector Jack

• Connect & Stream Audio from External Devices

• MP3 Digital Audio File Playback

• LCD Display Panel

• Front Aux-in, Front USB, No SD Card Reader

• Electronic Volume Control (Treble, Bass, Balance, Fader)Memory/Repeat/

Random/Intro Play

• EQ / Mute / Clock Control, English ID3

• ID3 Tag Song Readout for Artist Name/Song Title

• VA LCD/White Back-Light, Night Illumination: RGB

• 2 Pair RCA Output, ISO connector Line Out

• Equalizer (EQ) Electronic Audio Conguration

• Automatic Memory Preset Store/Scan Mode

• Repeat/Random Song Functions

Technical Specs:

• Remote Control Battery Operated, Requires (1) Coin-Type Battery

• Battery Type: 3V Lithium Bat. 240mAh Capacity

• Night illumination: RGB

• MAX. Power: 4 x 75W (300 Watts)

• PLL Electronic Tuning Radio Tuner

• ISO with 4 Pin/8 Pin Wire Connector

• Stereo/Mono Mode Selectable

• Audio Control: Treble, Bass, Balance, Fader

• Preset EQ: Flat/Pop/Rock/Class/Jazz/Off

• Switchable USA/Europe Tuner Frequencies by Software

• Max. USB Support: 64GB

• Power: DC 12V

• Current Consumption: 10A

• Product Dimension: 2.7’’ x 7.1’’ x 3.9’’ - inches

www.PyleUSA.com

13

PLMR3DNWT

Marine Stereo Receiver Power Amplier & Speaker Kit

AM/FM/MP3/BT/USB/AUX, Marine Stereo Receiver, Double DIN, 30 Preset
Memory Stations, LCD Display with Remote Control & 1 Pair of PLMR60W

Features:

• AM/FM/MP3/USB/AUX Marine Stereo Receiver

• Double DIN

• White / Grey button Panel, with 1 Pair PLMR60W

• LCD Display with Remote Control

• Marine Stereo Receiver System

• AM/FM Stereo Radio, 30 Station Memory

• Wireless BT Audio Ability

• Aux (3.5mm) Input Connector Jack

• Connect & Stream Audio from External Devices

• MP3 Digital Audio File Playback

• LCD Display Panel

• Front Aux-in, Front USB, No SD Card Reader

• Electronic Volume Control (Treble, Bass, Balance, Fader)Memory/Repeat/

Random/Intro Play

• EQ / Mute / Clock Control, English ID3

• ID3 Tag Song Readout for Artist Name/Song Title

• VA LCD/White Back-Light, Night Illumination: RGB

• 2 Pair RCA Output, ISO connector Line Out

• Equalizer (EQ) Electronic Audio Conguration

• Automatic Memory Preset Store/Scan Mode

• Repeat/Random Song Functions

Technical Specs:

• Remote Control Battery Operated, Requires (1) Coin-Type Battery

• Battery Type: 3V Lithium Bat. 240mAh Capacity

• Night illumination: RGB

• MAX. Power: 4 x 75W (300 Watts)

• PLL Electronic Tuning Radio Tuner

• ISO with 4 Pin/8 Pin Wire Connector

• Stereo/Mono Mode Selectable

• Audio Control: Treble, Bass, Balance, Fader

• Preset EQ: Flat/Pop/Rock/Class/Jazz/Off

• Switchable USA/Europe Tuner Frequencies by Software

• Max. USB Support: 64GB

• Power: DC 12V

• Current Consumption: 10A

• Product Dimension: 2.7’’ x 7.1’’ x 3.9’’ - inches

www.PyleUSA.com

14

What’s in the Box:

• Stereo Receiver

• ISO 4 Pin Power & 8 Pin Speaker

Wiring Harness

• Outer Trim frame Cover

• Remote Control

What’s in the Box:

• Stereo Receiver

• ISO 4 Pin Power & 8 Pin Speaker

Wiring Harness

• Outer Trim frame Cover

• 1 Pair of Marine Grade Speakers

PLMR60B

• Remote Control

What’s in the Box:

• Stereo Receiver

• ISO 4 Pin Power & 8 Pin Speaker

Wiring Harness

• Outer Trim frame Cover

• 1 Pair of Marine Grade Speakers

PLMR60W

• Remote Control

WIRELESS BT CONNECTIVITY:

• Built-in BT for Wireless Music Streaming

• Built-in Microphone for Hands-Free Calling

• Conveniently Reject/Answer Incoming Calls

• Compatible with All of Your Favorite Wireless BT Devices

(iPhone, Androids, Smartphones, iPad, Tablets, etc.)

• Wireless BT Version: 4.2

www.PyleUSA.com

15

Questions? Issues?

We are here to help!

Phone: [phone]

Email: [e-mail]