Pyle PLDVD-48 Owners manual

PLDVD48
OWNER’S MANUAL
Mobile Audio/Video System
Digital Audio Out-Coaxial
PLL Synthesizer Stereo Radio
DVD Player
Automatic Memory Storing
Fold Down Detachable Panel
Preset Equalization
Multi-audio Languages Function
Multi-angle Function
Parental Control
Remote Control
FEATURES
Compatible with PAL DVD (Video CD) and NTSC DVD (Video CD)
This player can play discs recorded in either PAL or NTSC format.
• A single LSI chip now integrates all major DVD playback circuit functions including MPEG2 decoder, video D/A converter, and audio decoders.
• L/R stereo analog audio outputs for connection to existing head unit aux inputs. Video output is composite video.
• Supplied remote handles multi-function software (multi-language audio-track/subtitle, multi-angle, multi­story, etc.), plus all basic functions.
USE THIS PRODUCT SAFELY
When Driving
Keep the volume level low enough to be aware of road and traffic conditions.
When Car Washing
Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage.
Use Authorized Service Centres
Do not attempt to disassemble or adjust this precision product. Please refer to the Service Centre list included with this product for service assistance.
For Installation
The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚.
When Parked
Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback.
Use the Proper Power Supply
This product is designed to operate with a 12 volt DC, negative ground battery system (the regular system in a North American car).
Protect the Disc Mechanism
Avoid inserting any foreign objects into the slot of this player. Failure to observe this may cause malfunction due to the precise mechanism of this unit.
2
CONTENTS
Safety Information ........................................................................................4
Disc Notes .....................................................................................................5
Installation .....................................................................................................6
Using the Detachable Front Panel .............................................................9
Wiring Connection ......................................................................................10
Location and Function of Keys..................................................................11
The Player ....................................................................................................11
Remote Control.............................................................................................12
Remote Control...........................................................................................14
Preparing the Remote Control......................................................................14
Loading/Ejecting a disc..............................................................................14
Loading a disc ..............................................................................................14
Ejecting a disc...............................................................................................14
Operation .....................................................................................................15
Basic Operation ............................................................................................15
Radio Operation............................................................................................16
Disc (DVD/VCD/CD/MP3) Operation ............................................................17
CDC Operation .............................................................................................22
DVD Changer Operation ...............................................................................22
AV IN Operation ............................................................................................23
Setup ...........................................................................................................24
Initial Setup ...................................................................................................24
General Setup...............................................................................................24
Speaker Setup ..............................................................................................26
Audio Setup ..................................................................................................26
Preferences Setup ........................................................................................27
Defaults Table ...............................................................................................30
Trouble Shooting.........................................................................................31
Specifications..............................................................................................32
3
SAFETY INFORMATION
CAUTION:
MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS MOBILE DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
Region Management Information
Region Management Information: This Mobile DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this Mobile DVD Player, this Mobile DVD Player cannot play this disc.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
4
DISC NOTES
Disc formats supported by this player
DVD
12 cm disc
Video CD
12 cm disc
CD
12 cm disc
MP3
12 cm disc
Handling and Cleaning
Dirt, dust, scratches and warping discs will cause misoperation.
Do not place stickers or make scratches on discs.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from damaging.
Do not place discs in the following places:
1. Direct sunlight
2. Dirty, dusty and damp areas
3. Near car heaters
4. On the seats or dashboard
Disc Cleaning
Use a dry soft cloth to wipe the surface. If the disc is quite dirty, use a soft cloth slightly moistured with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.
Note:
A disc may become somewhat scratched (although not enough to make it unusable) depending on your handle it and conditions in the usage environment. Note these scratches are not an indication of any problem with the player.
Label side up
Do not touch the underside of the disc
Do not bend
Wipe the disc from center toward the outside edge
Preparing New Discs with Rough Spots
A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the proper setting will not be performed and the player will not play the disc. Therefore, remove the rough edges in advance by using a ball point pen or pencil as shown on the right. To remove the rough edges, press the side of the pen or pencil against the inside and outside edges of the disc.
Rough spots on outside edge
Ball point pen or pencil
Rough spots on inside edge
5
INSTALLATION
Notes:
Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Install the unit where it does not get in the drivers way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum performance.
30˚
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard having an opening as shown below:
53 mm
182 mm
Installing the unit
Be sure you test all connections first, and then follow these steps to install the unit.
1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Press the release button on the front panel and remove the control panel (see the steps of removing the front panel).
4. Lift the top of the outer trim ring then pull it out to remove it.
5. The two supplied keys release tabs inside the unit's sleeve so you can remove it. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit.
Sleeve
L Key
Outer Trim Ring
Front Panel
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from Front (conventional DIN Front­mount) or Rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.
R Key
6
INSTALLATION
6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place.
Dashboard
Tabs
Screwdriver
Sleeve
7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.
8. Slide the unit into the sleeve until it locks into place.
9. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit.
Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard.
Spring Washer
Metal Strap
Mounting Bolt
Hex Nut
Plain Washer
Tapping Screw
10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel. (see the steps of installing the front panel).
Removing the unit
1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery's negative (-) terminal.
2. Remove the metal strap attached the back of the unit (if attached).
3. Press the release button to remove the front panel.
4. Lift the top of the outer trim ring then pull it out to remove it.
5. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.
7
INSTALLATION
DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.
Side view showing Screw Holes marked T, N
Factory Radio Mounting Bracket
Screw
Hook
Screw
Dashboard or Console
To fasten the unit to the factory radio mounting brackets.
1. Use a screwdriver to loose the hook's screws of the front left and right sides of the unit and remove the hooks.
2. Align the screw holes on the bracket
with the screw holes on the unit, and
then tighten the screws (5x5mm) on each side.
Note: the outer trim ring, sleeve and the metal strap are not used for method B installation.
8
USING THE DETACHABLE FRONT PANEL
To Detach the Front Panel
1. Press the OPEN button (OPEN) , then the front panel will be folded down.
Open
2. Remove the front panel by pulling its middle-hand side outward.
Front Panel
3. For safekeeping, store the front panel in the supplied protective case immediately after being removed.
Protective Case
Front Panel
4. Push the front metal plate into the main body. A ‘click sound should be heard.
To Reinstall the Front Panel
1. When the metal plate is folded down, insert the front panel into the metal plate then push them into the main body. A ‘click’ sound should be heard.
2. Note that if the front panel fails to lock in position properly, pressing control button may not function and display may be missing some segments.Press the OPEN button and then reinstall the front panel again.
Precautions when Handling
1. Do not drop the front panel.
2. Do not put pressure on the display or control buttons when detaching or reinstalling the front panel.
3. Do not touch the contacts on the front panel or on the main unit body. It may result in poor electrical contact.
4. If any dirt or foreign substances adhered on the contacts, they can be removed with a clean and dry cloth.
5. Do not expose the front panel to high temperatures or direct sunlight in anywhere.
6. Keep away any volatile agents (e.g. benzene, thinner, or insecticides) from touching the surface of the front panel.
7. Do not attempt to disassemble the front panel.
9
WIRING CONNECTION
ANTENNA
CONNECTOR
AV IN CABLE (BLACK)
AV OUT CABLE (GRAY)
AUDIO R IN (RED)
AUDIO L IN (WHITE)
VIDEO IN (YELLOW)
VIDEO OUT 1 (YELLOW)
VIDEO OUT 2 (YELLOW)
DIGITAL AUDIO (ORANGE)
DC OUT (BLACK)
(BLACK)
CONNECTOR SOCKET
RED
Rch
WHITE
Lch
RED
Rch
WHITE
Lch
PINK
TELEPHONE MUTE (OPTIONAL)
BLUE
POWER ANTENNA
IGNITION
RED
BLACK
SWITCH (ACC+) MEMORY BACK-UP(B+)
GROUND (B-)
YELLOW
FRONT Rch
SPEAKER
REAR Rch SPEAKER
GREEN
REMOTE CONTROL RECEIVER
FRONT Lch
SPEAKER
REAR Lch SPEAKER
BLACK YELLOW
RED
WHITE
YELLOW
VIDEO OUT
AUDIO L OUT
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
FUSE
FRONT RCA CABLE(BROWN)
REAR RCA CABLE(GREY)
SUBWOOFER CABLE (GREEN)
FOR DVD SIGNAL OUTPUT ONLY
AUDIO R OUT
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
CD CHANGER OR DVD CHANGER
CHOKE
BOX
MUTE WHILE TELEPHONING
If your unit is connected to a mobile telephone through the telephone mute line, the car radio’s volume will be muted as soon as you pick up the telephone. TEL MUTE flashes in the display.
10
LOCATION AND FUNCTION OF KEYS
THE PLAYER
615 8 13 10 19 12 11 5 4 11737916
2
1.
(PWR/ILL)
2.
3.
4. DISP
5. IR
6. MODE/(SW)
7. OPEN
8. Vacuum Fluorescent Display
9. MUT/ENT
10. ST/LOC/TITLE
11. VOL+
12. VOL-
13. MENU/BAND
When remove the front panel:
18 20 21 22 23 24 25 2614
28 2927
14. 1-6 preset buttons
15. SMART
16.
17.
18. AMS/ STOP
19. SEL
20.
21. SCN
22. RPT
23. SHF
24. CD-
25. CD+
26. Reset button
27. Disc Slot
28. LED
29.Eject button
11
Loading...
+ 25 hidden pages