Please read all of the installation instructions carefully before installing the product. Improper installation
will void manufacturer's warranty. The installation instructions do not apply to all types of vehicles, and
are written as guidelines to assist in installing the system. Please consult an experienced technician if you
are not comfortable installing the product. Prior to using and installing the Backup Camera System, please
read the safety information provided in this user manual. Be sure to use the product as outlined in this user
manual. Altercation or modications carried out without appropriate authorization may invalidate the user's
right to operate the equipment.
WARNING: Failure to read and follow these warnings and instructions may result in serious injury, including
damaged property, so please pay close attention and exhibit the utmost care.
• The Digital Backup Camera is designed as an aid to the driver in detecting potentially hazardous driving
conditions, obstructions, and large stationary objects. You,the driver, must also remember to drive safely
and properly. Use of the Digital Backup Camera is not a substitute for safe, proper and legaldriving
practices.
• Never back up while looking only at your connected monitor display screen. You should always check
behind and around the vehicle when backing up just as you would if the vehicle did not have the Digital
Backup Camera. Always make sure your driving area is clear. Always back up slowly and with caution.
• Never depend on the Backup Camera entirely when backing up. The image on the monitor display screen
may be slightly dierent from actual and real-time conditions. Objects viewed in the rear view monitor
dier from actual distances because a wide-angle lens is used. So use the camera as an aid and always
follow intended driving practices to properly judge distances from objects.
• The Backup Camera's assisted low lux lighting performance feature is also an aid to a driver. Always use
your own eyes to conrm the vehicle's surroundings, as the displayed image may be not well lit or not
entirely visible. Always proceed with caution and perform double-checks before proceeding.
• The area displayed by the Backup Camera is limited. It does not display objects that are close to or just
below the bumper, underneath the vehicle, or objects out of the camera's view. The camera's view can
change according to your vehicle's orientation on the road or changing road conditions.
• Be sure to check the camera is properly functioning, is properly positioned and securely mounted,
every time you operate your vehicle.
• Make sure your trunk or hatch operates correctly, as intended before and after installation.
• Proceed with caution when cleaning your vehicle around the camera. Avoid excess water exposure around
the camera especially with spraying or a power washer.
• Please make sure to keep the camera clean and unobstructed from any debris
• Follow all traffic laws and motor vehicle regulations.
• Consult locallaws and regulations for any restrictions on installation or use.
• Using a Backup Camera System is not adequate enough to completely eliminate a vehicle's blind spot.
Always remember to drive with caution, following all traffic laws.
1
www.PyleUSA.com
System Installation and Wiring
Notes:
Camera System installation on diesel vehicles may require a slightly dierent wiring install.
These installation instructions do not apply to all types of vehicles. They are meant only as a general guide
due to the large number of vehicle makes and models. Consult your local motor vehicle laws on the use of
this product to be sure it is permitted.
Through installation of this backup camera system, you should be sure as to not degrade, damage or compromise the safety of any system or device on your vehicle.
Improper installation and wiring of the Vehicle Back-Up Camera system may damage the vehicle's electrical
system, including vital vehicle computer and operating systems. That could lead to an accident or re,
causing property damage and /or serious personal injury. It is highly recommended to seek professional
installation advice from a qualied auto electrician or, in the alternative, to have the installation performed
by a qualied auto electrician.
Please ensure that monitor is secured and mounted where it would NOT obstruct any OEM vehicle safety
features. In an event of an accident, manufacturer is not responsible for bodily injury caused by the monitor
being a projectile. Select location for mounting the monitor in desired location. Ensure monitor location will
not obstruct your vision while driving.
The manufacturer assumes no liability for damage caused to your vehicle due to improper installation or use.
Caution: This unit is designed to operate on a 12V/24V DC NEGATIVE GROUND electrical system. Connecting
to other types of electrical systems will cause damage to your vehicle. Please contact the manufacturer if you
are unaware of the system type in your vehicle.
Quick Installation:
The 2.4 G wireless modules come in two parts, they are used as the "Transmitter” and the "Receiver". When
installing, the “Transmitter”, should be connected to the camera (the camera is preferably mounted in the rear
of the vehicle, just above the license plate). The receiver is built in the display monitor. This receives the signal
from the camera connected to the transmitter.
Connect the transmitter's red power wire, of the DC 12V input cable, to the positive 12V reverse tail light in
the rear of your car. Then connect the black wire, of the DC 12V input cable, and ground properly.
The transmitter then connects to the camera, and will supply power to the camera directly.
2
www.PyleUSA.com
Installation Transcript:
1. Locate the reverse taillight wiring behind your vehicle's reverse light. You may need to remove an interior
panel, or other cover, in order to locate the wiring. Connect a wireless module to the reverse light.
2. Connect the camera to the wireless module, then mount the camera in the desired location.
3. Mount the display monitor.
Camera Connection (Using the Wireless Transmitter):
a. Connect the wireless module's Red wire to your vehicle's reverse light positive wire.
b. Connect the wireless module's Black wire to your vehicle's reverse light negative wire.
c. Ensure the wires are safely and securely connected, with proper isolation applied to all connections.
d. Determine the best location to mount the wireless modules, as they are not waterproof and need a safe
and secure location.
Monitor Connection
a. Stick the monitor to window shield using the suction cup.
b. Use the cigarette plug to get power.
Notes:
• Determine the best location for the camera (Keep in mind that you must run the cable from the camera to
the transmitter). You may need to drill a small hole in the panel near your license plate (The camera is
preferably mounted just above the license plate).
• Be sure when running the connection cables to leave a small amount of slack so you can still move the
camera around the license plate, if you decide to slightly adjust the camera's positioning at a later time.
• Test the camera and monitor system once you have completed installation. Activate your car and turn the
key into the accessory position. Your connected monitor will automatically power on if properly
connected to a power source. Placing your vehicle in reverse should provide a picture.
www.PyleUSA.com
3
PLCM4378WIR
POWE
V1 / V2
R
1. Long press for power ON/OFF; Short press
for Video1 / Vide02 switch.
2. Positive Adjustment
U
MEN
3. Menu
4. Negative Adjustment
R
PLCM4378WIR
5. DC power input
6. Optional Video input: you can connect to a wired camera input in case the supplied
wireless camera does not work.
POWER
1 / V2
V
Camera
DC
Monitor
MENU
R
PLCM 4378 WIR
Cigarette plug
DC
C
D
C
a
m
era Inp
u
t
R
Wirel ess Video Tr ansmitt er
+12v
-12v
Taillight
Video Transmitter
Remarks: After wiring up, please seal this transmitter box for water proof with the small tape provided.
4
www.PyleUSA.com
Backup Camera Systems
Angle Adjustable Camera Lens
Located on the camera housing are 2 screws which
lock the camera lens angle in position.
The screws may be loosened to allow camera lens
angle adjustment
Loosen the screws, adjust the camera lens into the
desired angle. then tighten the screws securely.
Be sure as to not overtighten the screws.
www.PyleUSA.com
5
Loading...