Page 1
Playing Music:
1. Press
2.
Press
3. Press to start or pause the music
4. Press shortly for next track
5.
Press shortly for Previous track
6. Press shortly for volume up
7. Press shortly for volume down
shortly for control the red background light
PLBT27
Wiring Diagram
Line in L (White)
Line in from Head Unit or
Other Aux-In Device
Line in R (Red)
Black
Red
+
-
Battery
4
Line out L (White)
Line out to Amplifier
Line out R (Red)
Universal Bluetooth Receiver Control Adapter/
Wireless Audio Controller
OWNER’S MANUAL
Page 2
PLBT27
Universal Bluetooth Receiver Control Adapter/
Wireless Audio Controller
FEATURES
Adds Simple & Convenient Remote Music Control
Built-in Bluetooth for Wireless Streaming Receiver Ability
Mounts to Handlebars, Dashboards, Consoles, Support Bars
Universal Mobile Vehicle Controller Design
NFC (Near Field Communication) Sensor Support
Instant 'Connect & Stream' Android Device Ability
Aux (3.5mm) Input Connector Jack
Ability to Connect Additional External Devices
(iPhone, Android, Smartphone, iPad, Tablet, etc.)
RCA (L/R) Line Input Connector Jacks
RCA (L/R) Line Output Connector Jacks
Simple Push Button Controls
Play, Pause, Previous, Next, Volume Up/Down
Illuminated Backlit Buttons for Easy Viewing
Includes All Necessary Cables, Wiring, Mounting Brackets, Hardware
Used for Motorcycle, Golf Cart, ATV/UTV, Marine Vehicles
Bluetooth Console Controller:
Acts as the Bluetooth Signal Receiver (Source Unit)
Ability to Function / Replace the Headunit Receiver
Bluetooth Version: 3.0
Bluetooth Network Name: Pyle Audio
Bluetooth Network Password: 1234
Dimensions (L x W x H): 3.82'' x 2.13'' x 1.14''
Weight: 0.257 lbs.
WHAT IS INCLUDED?
3
4
1
1. Bluetooth Remote Control
2. Bluetooth Controller Hook
3. Black Industrial Velcro for P Clamp
4. Amplifier 12 Volt(+/-) Ground Blue Spade Terminal
5. “P” and “Z” shaped Clamps for Handlebar
6. Exten sional wire for 3.5mm Aux-In
2
1
6
5
INSTALLATION
INSTALLATION
(MODE 1“Handlebar Mount”)
1. Install “P” shaped clamp
or “Z” shaped bracket threaded
(item#5) on to the Bluetooth
controller hook. (packed with
Bluetooth controller). Use the
provided bolt to fix on the
handlebar. The provided foam
and rubber pads can be used
to accomplish tight and secure
mounting.
2. Slide the Bluetooth
controller into the hook
3. Press down the Bluetooth
controller hook and then slide
out the Bluetooth controller
box at the same time to
remove the Bluetooth
controller
(MODE 2“Push-Fixed in Mount”)
Decide the place for Bluetooth remote
installation. Draw and cut the size into
85 x 49mm ( L x W )
Push in the Bluetooth remote
2
AUX Input
On/Off &
Background Light Volume Up
Play / Pause Previous Track Volume Down
Next Track
NFC Tag
Position
Bluetooth Pairing and Connection:
1.
Connect Bluetooth controller box to your device
Press and Hold
2.
3.
The system will automatically go into pairing mode The power indicator will
for three seconds until power indicator lights (red)
turn red for about 4-6 seconds and then alternating red and blue (Bluetooth
blue Power red) Please be sure that Bluetooth is turned on your device and
Pyle Audio
Select “
(if the Bluetooth controller is connected, the light will turn blue and not flash)
4.
Bluetooth password “ 1234 ”
When the device is out of Bluetooth range, Bluetooth will be disconnected
5.
” on your device to connect Bluetooth controller
automatically and automatically reconnect when detected in range again.
(If not please just repeat steps 1 and 2)
When Bluetooth is disconnected or the 3.5mm AUX Input is plugged in, the
6.
power indicator will glow red.
NFC Pairing and Connection:
1.
Have your device touch the NFC tag on the controller and then you will
receive the notification to require password
2.
Enter the password
time connection, no need to enter password when connect NFC again)
3.
After turn on the Bluetooth function by NFC, the operation procedure is
same as the above “ Bluetooth Pairing and Connection”
4.
Touch the NFC tag again to turn off the Bluetooth function.
“ 1234 ”
to turn on the Bluetooth. (This is only for the first
3
Loading...