Page 1
pla885
pla1085
speaker connections
4 ch amp PLA885•PLA1085
blue
2 CH Stereo Output Mode with Mono Bridged Subwoofer Output
wave
L
SPEAKERS
speaker connections
blue
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
R
SUBWOOFER
5 ch amps PLA1585
28
wave
pla1585
5 CH Output Mode
FRONT speakers
L
REAR speakers
RL
29
R
SUBWOOFER
Page 2
www.pyleaudio.com
damage.
improperly serviced, or subject to misuse, neglect, or accidental
This warranty will be considered void if the unit was tampered with,
replacement of the defective unit when it is returned to us prepaid.
Our obligation under this warranty is limited to the repair or
expiration date.
handling, and insurance, or provide your Visa/MC number with
• also include a check or money order for $12.00 for return shipping,
and R.A. number
• include in your letter your return address, daytime phone number,
• A brief letter indicating the problem you are experiencing
• A copy of your sales receipt or other proof of purchase
You must also include the following items:
Brooklyn, NY 11204
1600 63rd Street
Pyle Service Center
R.A.#
and shipped prepaid to:
When returning a product to us for warranty service it must be carefully packed
relating to your return.
R.A.# must appear on the outside of your package and on all paperwork
number at (718) 236-6948 to obtain a Return Authorization number. This
To obtain warranty service you must first call our Consumer Return Hotline
your unit will be repaired or replaced at the sole discretion of Pyle.
Should the product fail due to factory defects in material or workmanship,
warranty is limited to the original retail purchase.
in material and workmanship for two (2) years from the date of purchase. This
shipment. Products purchased in the USA are warranted to be free of defects
All Pyle products are carefully constructed and thoroughly tested before
wave
amplifiers
blue
limited warranty policy
user’s manual
blue
wave
high performance car audio amplifier
PLA485
PLA785
PLA885
PLA1085
PLA1285
PLA1585
Page 3
congratulations...
blue
on your purchase of a Pyle Blue Wave Series amplifier. This amplifier
extends the Pyle tradition into a totally new series of amps, designed
from the ground up to deliver the power, performance and flexibility
the modern car audio enthusiast demands.
When you check the list of features offered by the PLA485, PLA785,
PLA885, PLA1085, PLA1285, and PLA1585, you’ll know you made
the right choice with a Pyle Blue Wave amplifier.
wave
table of contents
blue
general features
features and specifications
PLA485
PLA785
PLA1285
PLA885/1085
features and specifications
PLA1585
electrical connections
PLA485/785/1285
PLA885/1085/1585
stereo input connections
PLA485/785/1285
mono input connections
PLA485/785/1285
2/4 channel input connections
PLA885/1085
high level input connections
PLA885/1085
wave
2-3
4-5
6-7
8-9
10-11
12-13
14
15
16
17
18
19
high level mono input connections
high level mono input connections
PLA485/785/1285
protection circuitry and troubleshooting
mono input connections
PLA885/1085
PLA885/1085
5 channel input connections
PLA1585
high level input connections
PLA1585
mono input connections
PLA1585
PLA1585
speaker connections
speaker connections
PLA885/1085
speaker connections
PLA1585
mounting and installation
precautions
20
21
22
23
24
25
26
27-28
29-30
31
32
33
Page 4
general features
blue
PLA485
High Performance 600 Watt 2 Channel
Bridgeable MOSFET Amplifier
· 300 Watts x 2 Output
· 600 Watts x 1 Bridged Output
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Input
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
wave
PLA785
High Performance 800 Watt 2 Channel
Bridgeable MOSFET Amplifier
· 400 Watts x 2 Output
· 800 Watts x 1 Bridged Output
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Input
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
PLA1285
High Performance 1400 Watt 2 Channel
Bridgeable MOSFET Amplifier
· 700 Watts x 2 Output
· 1400 Watts x 1 Bridged Output
· Variable Hi/Lo Electronic Crossover Network
· Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Input
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
2
blue
PLA885
High Performance 1000 Watt 4 Channel
Bridgeable MOSFET Amplifier
· 250 Watts x 4 Output
· 500W x 2 Bridged Output (250W x 2 + 500W x 1)
· Dual Variable Hi/Lo Electronic Crossover Network
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Inputs
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
· Tri-Mode Configurable
wave
PLA1085
High Performance 1400 Watt 4 Channel
Bridgeable MOSFET Amplifier
· 350 Watts x 4 Output
· 700W x 2 Bridged Output (350W x 2 + 700W x 1)
· Dual Variable Hi/Lo Electronic Crossover Network
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Inputs
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
· Tri-Mode Configurable
PLA1585
High Performance 1400 Watt 5 Channel
Bridgeable MOSFET Amplifier
· 250 Watts x 4 Output.+ 400 Watts x 1 Output
· 500 W x 2 Bridged Output ( 250 W x 2 + 500 W x 1)
· Dual Variable Hi/Lo Electronic Crossover Network
· Dual Variable Bass Boost (0 - +18 dB @ 60Hz)
· Variable Input Level (Gain) Control
· Remote Turn On/Off
· Gold Plated RCA Inputs
· High Level MOLEX Inputs
· Power ON LED Indicator
· LED Protection Indicator
· S/N Ratio: > 95 dB
· THD: <0.04%
· Thermal Protection
· Overload Protection
· Short Circuit Protection
· Anti-Thump Turn-On
· Tri-Mode Configurable
3
Page 5
pla485
features and controls
blue
input level control
crossover mode selector
bass boost level
high level inputs
2 ch amp PLA485
wave
high pass frequency control
low pass frequency control
4
protection LED
low level inputs
speaker connections
blue
crossover mode selector
input level control
low pass frequency control
high pass frequency control
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
features and specifications
2 ch amp PLA485
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in “low pass” mode, this control
sets the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
power LED
power terminals
power fuse
PLA485
wave
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
frequency response
input impedance
low level inputs
high level inputs
input sensitivity
low level inputs
high level inputs
power supply voltage
matching speaker impedance
stereo mode
bridged mode
maximum current draw
dimensions (W x H x L)
mm
inches
2 channel amplifier
50 Watts x 2
80 Watts x 2
300 Watts x 2
15 Hz-30 KHz
10K Ohms
100 Ohms
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
2-4 Ohms
4-8 Ohms
15A
300 x 62 x 209
11.8 x 2.4 x 8.2
5
Page 6
pla785
features and controls
blue
input level control
crossover mode selector
bass boost level
high level inputs
2 ch amp PLA785
wave
high pass frequency control
low pass frequency control
6
protection LED
low level inputs
speaker connections
blue
crossover mode selector
input level control
low pass frequency control
high pass frequency control
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
features and specifications
2 ch amp PLA785
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in “low pass” mode, this control
sets the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
power LED
power terminals
power fuse
PLA785
wave
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
frequency response
input impedance
low level inputs
high level inputs
input sensitivity
low level inputs
high level inputs
power supply voltage
matching speaker impedance
stereo mode
bridged mode
maximum current draw
dimensions (W x H x L)
mm
inches
2 channel amplifier
85 Watts x 2
125 Watts x 2
400 Watts x 2
15 Hz-30 KHz
10K Ohms
100 Ohms
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
2-4 Ohms
4-8 Ohms
20A
300 x 62 x 281
11.8 x 2.4 x 11
7
Page 7
pla1285
features and controls
blue
input level control
crossover mode selector
bass boost level
high level inputs
2 ch amp PLA1285
wave
high pass frequency control
low pass frequency control
8
protection LED
low level inputs
speaker connections
blue
crossover mode selector
input level control
low pass frequency control
high pass frequency control
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
features and specifications
2 ch amp PLA1285
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in “low pass” mode, this control sets
the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
power LED
power terminals
power fuse
PLA1285
wave
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
frequency response
input impedance
low level inputs
high level inputs
input sensitivity
low level inputs
high level inputs
power supply voltage
matching speaker impedance
stereo mode
bridged mode
maximum current draw
dimensions (W x H x L)
mm
inches
2 channel amplifier
125 Watts x 2
200 Watts x 2
700 Watts x 2
15 Hz-30 KHz
10K Ohms
100 Ohms
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
2-4 Ohms
4-8 Ohms
30A
300 x 62 x 403
11.8 x 2.4 x 15.9
9
Page 8
features and controls
blue
4 ch amps PLA885•PLA1085
wave
pla885
pla1085
ch 3/4 high pass frequency control
ch 3/4 crossover mode selector switch
ch 3/4 input level control
ch 3/4 bass boost level control
ch 3/4 low pass frequency control
ch 3/4 low level inputs
ch 3/4 high level inputs
power LED
protection LED
speaker connections
ch 1/2 high pass frequency control
ch 1/2 crossover mode selector switch
ch 1/2 input level control
ch 1/2 bass boost level control
ch 1/2 low pass frequency control
ch 1/2 high level inputs
ch 1/2 low level inputs
power terminals
10
blue
dual crossover mode selectors
dual input level controls
dual low pass frequency controls
dual high pass frequency controls
dual bass boost level controls
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
features and specifications
4 ch amps PLA885•PLA1085
when used with normal, full range systems, set these switches to “FULL.”
If you wish to use the internal crossovers to power a driver of specific
frequency range, use the “LOWPASS” or “HIGHPASS” settings.
use these controls to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level controls until distortion begins to occur, and reduce slightly
from this point.
when one or both of the crossover selector switches is in “low pass”
mode, one can set the upper frequency limit for audio program sent to
the speakers.
when the one or both of crossover selector switch is in “high pass” mode,
one can set the lower frequency limit for audio program sent to the
speakers.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB in either or both pairs of channels.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
fuse
wave
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
frequency response
input impedance
low level inputs
high level inputs
input sensitivity
low level inputs
high level inputs
power supply voltage
matching speaker impedance
stereo mode
bridged mode
maximum current draw
dimensions (W x H x L)
PLA
mm
inches
885
4 channel amplifier
70 Watts x 4
100 Watts x 4
250 Watts x 4
20 A 40 A
300 x 62 x 305
11.8 x 2.4 x 12
PLA
1085
4 channel amplifier
100 Watts x 4
150 Watts x 4
350 Watts x 4
15 Hz-30 KHz
10K Ohms
100 Ohms
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
2-4 Ohms
4-8 Ohms
300 x 62 x 403
11.8 x 2.4 x 15.9
11
Page 9
features and controls
blue
4ch/5ch mode selector switch
ch 5 input level control
5 ch amp PLA1585
wave
ch 5 crossover mode selector switch
ch 5 low pass frequency control
ch 5 bass boost level control
pla1585
ch 3/4 crossover mode selector switch
ch 3/4 high pass frequency control
ch 3/4 input level control
ch 3/4 bass boost level control
ch 3/4 low pass frequency control
protection LED
power LED
ch 3/4 high level inputs
ch 5 high level inputs
speaker connections
ch 1/2 crossover mode selector switch
ch 1/2 high pass frequency control
ch 1/2 input level control
ch 1/2 bass boost level control
ch 1/2 low pass frequency control
ch 1/2 high level inputs
ch 1/2 low level inputs
ch 3/4 low level inputs
power terminals
fuse
12
blue
crossover mode selector
input level control
low pass frequency control
high pass frequency control
bass boost level control
low level inputs
high level inputs
power LED
protection LED
power fuse
power terminals
speaker connections
features and specifications
5 ch amp PLA1585
when used with normal, full range systems, set this switch to “FULL.” If
you wish to use the internal crossover to power a driver of specific frequency
range, use the “LOWPASS” or “HIGHPASS” settings.
use this control to match the outputs of your head unit to the amplifier.
Starting with your head unit set at about the 2 o’clock position, increase
the amp level control until distortion begins to occur, and reduce slightly
from this point.
when the crossover selector switch is in “low pass” mode, this control sets
the upper frequency limit for audio program sent to the speakers.
when the crossover selector switch is in “high pass” mode, this control
sets the lower frequency limit for audio program sent to the speakers.
this control permits adjustment of the bass level up to an increase of
approximately 18 dB.
this amp features gold-plated RCA input jacks for high impedance input.
Use these with car stereo output which uses RCA-type connector cables.
if your car stereo lacks RCA-type output jacks, you may connect speaker
output leads to these input connectors.
this indicator is illuminated when power is applied.
this indicator is illuminated when built-in protection circuitry is activated.
the fuse protects the amplifier and your car’s electrical system from short
circuit conditions.
use these connectors to deliver power, ground and remote turn-on control
to the amplifier.
these terminals are 14K gold plated to guarantee high conductivity and
minimum signal loss.
PLA1585
wave
output power @ 14.4v DC, 1KHz
RMS Power @ 4 Ohms
RMS Power @ 2 Ohms
Maximum Power Output
frequency response
input impedance
low level inputs
high level inputs
input sensitivity
low level inputs
high level inputs
power supply voltage
matching speaker impedance
stereo mode
bridged mode
maximum current draw
dimensions (W x H x L)
mm
inches
5 channel amplifier
70 Watts x 4
100 Watts x 4
250 Watts x 4
15 Hz-30 KHz
10K Ohms
100 Ohms
250mV
2.5V
14.4V DC Neg. Ground (10.5-16V)
2-4 Ohms
4-8 Ohms
30A
300 x 62 x 449
11.8 x 2.4 x 17.7
+ 100 Watts x 1
+ 150 Watts x 1
+ 400 Watts x 1
13
Page 10
pla485
pla785
pla1285
electrical connections
blue
2 ch amps PLA485•PLA785•PLA1285
wave
14
12V battery
head unit
pla885
pla1085
pla1585
electrical connections
blue
to remote turn-on
4 ch amps PLA885•PLA1085
5 ch amps PLA1585
wave
+12V
12V battery
15
head unit
to remote turn-on
+12V
to remote turn-on
+12V
12V battery
head unit
Page 11
pla485
pla785
pla1285
stereo input connections
blue
using low level inputs
2 ch amps PLA485•PLA785•PLA1285
wave
L/R Audio
Outputs
head unit
L L RR
from spealer terminals
mono input connections
blue
head unit
PLEASE NOTE! If using high
level inputs, do not use the
using high level inputs
wiring harness
2 ch amps PLA485•PLA785•PLA1285
low level RCA inputs at the
same time!
wave
16
pla485
pla785
pla1285
using low level inputs
To a second amplifier
To a second amplifier
Y Adaptors
head unit
RRLL
head unit
using high level inputs
wiring harnesswiring harness
17
PLEASE NOTE! If using high
level inputs, do not use the
low level RCA inputs at the
same time!
from spealer terminals
Page 12
pla885
pla1085
2/4 channel input connections
blue
4 CH input connections using low level inputs
4 ch amps PLA885•PLA1085
wave
L/R REAR
Audio Outputs
2 CH input connections using low level inputs
high level input connections
blue
L/R FRONT
Audio Outputs
L
Y adaptors
R
4 ch amps PLA885•PLA1085
wave
head unit
18
pla885
pla1085
PLEASE NOTE! If using high level
inputs, do not use the low level
RCA inputs at the same time!
4 CH floating ground connections
L R FRONTRLREAR
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
ORANGE
BLACK
BLACK
ORANGE
4 CH harness wiring for common ground connections
CH 3/4
L R FRONTRLREAR
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
ORANGE
BLACK
BLACK
ORANGE
19
CH 1/2
Page 13
pla885
pla1085
mono input connections
4 ch amps PLA885•PLA1085
blue
4 CH mono input connections using low level inputs
RIGHT FRONT Audio Outputs
RIGHT REAR Audio Outputs
2 CH mono input connections using low level inputs
wave
head unit
LEFT FRONT Audio Outputs
LEFT REAR Audio Outputs
20
pla885
pla1085
high level mono input connections
blue
4 CH floating ground connections
L
Y adaptors
R
4 ch amps PLA885•PLA1085
wave
CH 3/4
21
ORANGE
BLACK
BLACK
ORANGE
PLEASE NOTE! If using high level
inputs, do not use the low level
RCA inputs at the same time!
R L
from speaker terminals
for common ground connections
ORANGE
BLACK
BLACK
ORANGE
4 CH harness wiring
ORANGE
BLACK
BLACK
ORANGE
CH 1/2
R L
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
Page 14
pla1585
5 channel input connections
blue
4 CH input connections using low level inputs
5 ch amps PLA1585
wave
2 CH input connections using low level inputs
high level input connections
blue
L/R REAR
Audio Outputs
L/R FRONT
Audio Outputs
Y adaptors
5 ch amps PLA1585
wave
head unit
22
head unit
R
L
pla1585
PLEASE NOTE! If using high level
inputs, do not use the low level
RCA inputs at the same time!
4 CH floating ground connections
L R FRONTRLREAR
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
ORANGE
BLACK
BLACK
ORANGE
SWITCH
POSITION
5 CH
4 CH
Attention: Use High Level MOLEX Input for 5CH mode only.
INPUT OUTPUT
4 CH
5 CH
5 CH
5 CH
5 CH harness wiring for common ground connections
CH 3/4
L R FRONTRLREAR
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
ORANGE
BLACK
BLACK
ORANGE
23
CH 1/2
Page 15
pla1585
mono input connections
5 ch amps PLA1585
blue
4 CH mono input connections using low level inputs
wave
2 CH input connections using low level inputs
high level mono input connections
blue
R CH FRONT/REAR
Audio Outputs
L CH FRONT/REAR
Audio Outputs
Y adaptors
5 ch amps PLA1585
wave
head unit
24
head unit
R
L
pla1585
PLEASE NOTE! If using high level
inputs, do not use the low level
RCA inputs at the same time!
4 CH floating ground connections
R L
ORANGE
BLACK
BLACK
ORANGE
from speaker terminals
ORANGE
BLACK
BLACK
ORANGE
4 CH harness wiring
for common ground connections
ORANGE
BLACK
BLACK
ORANGE
CH 3/4
CH 1/2
R L
from speaker terminals
25
ORANGE
BLACK
BLACK
ORANGE
Page 16
pla485
pla785
pla1285
speaker connections
blue
Stereo Output Mode
LEFT speaker RIGHT speaker
2 ch amps PLA485•PLA785•PLA1285
wave
26
Bridged Mono Output Mode
pla885
pla1085
speaker connections
blue
4 CH Output Mode
MINIMUM
SPEAKER
IMPEDANCE
speaker
4 ch amps PLA885•PLA1085
4 OHMS!
wave
27
Bridged Dual Mono Output Mode
L R
FRONT speakers
L R
R L
speakers
REAR speakers
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
Page 17
pla1585
speaker connections
blue
2 CH Bridged Output Mode with Subwoofer Output
L
5 ch amp PLA1585
wave
30
MINIMUM
SPEAKER
IMPEDANCE
4 OHMS!
mounting
Your new Pyle Blue Wave Series amplifier comes complete with all required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember
that it is a high-power electronic device capable of generating high heat.
For this reason, always choose a location in your vehicle which has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to mount
the amp in such a manner as to allow reasonable airflow over the cooling fins.
Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of
the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen.
Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting
surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely.
blue
R
SUBWOOFER
mounting and installation
PLA485•PLA785•PLA885•PLA1085•PLA1285•PLA1585
wave
wiring tips
fuses
When making electrical connections to your amplifier, please observe the
following:
Use at least 8 gauge wire for power and ground connections.
Wire the amplifier directly to the car battery.
For the ground connection, use the shortest possible wire to a good chassis ground point.
Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna.
About power fuses:
Pyle Blue Wave Series amplifiers feature built-in fuse systems. These fuses protect both the
amplifier and the electrical system in your vehicle from fault conditions. If you ever need to
replace the fuse in your Pyle Blue Wave Series amp, use a fuse of exactly the same type and
rating. A different type or rating of fuse may result in damage or fire.
31
Page 18
protection
circuitry
The built-in protection circuitry in the Pyle Blue
Wave amplifiers will disable the amplifier if it senses
an input overload, a speaker short circuit, or extreme
temperature conditions.
blue
troubleshooting
No output.
Confirm that all terminal strip connections are secure and tight.
Check both in-line and built-in fuses. Both the +12V and the Remote terminals must have +12v referenced to chassis
ground.
wave
When the protection circuit is activated by any of
these conditions, the Protection LED will be
illuminated.
If this occurs, carefully inspect the system to
determine the source of the problem.
• If the shutdown was a result of a thermal overload
condition, allow the amplifier to cool down before
attempting to restart it.
• If the shutdown was a result of an input overload,
or speaker short circuit, be sure to correct the
condition before restarting.
The amplifier can be restarted by turning the remote
power OFF and then ON again.
Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To
check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the
amp). Briefly tap the center pin of each of the disconnected RCA plugs with your finger . This should produce a noise
(feedback) in your speakers.
Only one channel works.
Confirm that all terminal strip connections are secure and tight.
Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint.
If you are using the Low Level RCA input, reverse the input plugs at the amplifier (i.e., switch the L with the R). If
the channels which is silent switches to the other side, the problem is either in the head unit/other source or the
connecting cables.
Weak output.
Readjust the Input Level Control(s) to better suit the input signal.
Noise in the audio.
If the noise is a “whine” whose pitch follows the engine speed, confirm that the amplifier and any other signal
sources (head unit, etc.) are properly grounded.
If the noise is a “clicking” or “popping” noise whose rate follows the engine speed, this usually means that the
vehicle is equipped with resistor spark plugs and wires, or that the ignition is in need of service.
Check the rounting of the speaker and input wires to make sure they are not adjacent to wires which interconnect
lights and other accessories.
If the above steps fail to improve or clear noise interference, the system should be checked by a professional mobile
audio installer.
32
precautions notes
Do not operate the amplifier when it is unmounted.
Attach all audio system components securely within
the automobile to prevent damage, especially in an
accident.
Do not mount this amplifier so that the wire
connections are unprotected, or in a pinched
condition, or likely to be damaged by nearby objects.
Before making or breaking power connections in
your system, disconnect the vehicle battery. Confirm
that your head unit or other equipment is turned off
while connecting the input jacks and speaker
terminals.
If you need to replace the power fuse, do so only
with a fuse identical to that supplied with the amplifier .
Using a fuse of a different type or rating may result
in damage that isn’t covered in the manufacturer’s
warranty.
blue
wave
33
Loading...