Indoor Wireless/Wired HD P2P Network Camera Pro.
(with H.264 image compression)
Instruction Manual
WIRELESS SETUP
1. Download the App:
Download “Pyle IP Pro” in Apple Store or
Google Play
2. Attach the wireless antenna to your
camera. Plug in your camera into power
in the SAME room as your home’s
wireless router - wait 2 minutes for the
camera to pan and tilt through the full
range of motion
3. Reset the camera using a pin - Hold
in the reset pin for 10 - 12 seconds until
you hear an audible chirp. Wait again
1 - 2 min for the camera to reset and run
through the full range of pan and tilt
4. Check in your mobile phone’s system
settings that you are currently connected
to your home router’s wireless network Setup will not work using cell data
PIPCAMHD82
Quick Start Guide
Find FAQs including setup video and support online at www.pipcamwireless.com
5. Open the Pyle IP Pro app and select
the “add camera” option
6. Select “One Key Cong”
7. Enter the password for your home
wireless network
8. Wait for the camera to chirp indicating
the connection has been made
WIRELESS SETUP
1. Plug your camera into AC power
2. Plug your camera directly into
your router with wired Ethernet wire
(included)
NOTE: Wired Ethernet is required for
setup. Wireless will be congured later.
NOTE: Wait 2-3 minutes for camera
to boot. You will see the camera run
through a full range of pan and tilt
motion.
3. When boot up completes, your
camera's ethernet port will ash yellow
and green lights indicating the camera is
connected to your router.
NOTE: If lights are not ickering the
camera is not receiving data. Please
check for faulty ethernet cable and that
your router is working with another
device.
4. Check that you have WIFI enabled in
your phone's system settings
WIRED SETUP
5. Open up the Pyle IP Pro app and select
"add camera"
6. Select the option to “Scan QR Code”
7. Scan the QR code on your camera with
your smartphone's camera
8. Name your camera to your preference
- Then input the camera default password
"pylecam"
WIRED SETUP
9. Make sure to change the password to
a custom password
10. Now navigate to the “Camera” tab to
see a list of all of your cameras. Select the
newly added camera to check you can
see the video feed.
11. Select “Edit” in the top left corner,
then “set” on your camera’s entry.
12. Select “WIFI Setting”
13. Wait for the list of available WIFI
networks to appear. Select your home
network.
- No networks displayed? Go to www.
pipcamwireless.com and search “I am
having trouble connecting to WiFi” for
more help
WIRED SETUP
14. Add the wireless password for your
home router
Note: Passwords are case sensitive and the
app isn't smart enough to tell you if you have
typed it correctly. If you have any doubt about
your home network's password I would
recommend troubleshooting the value in
your smartphone's WIFI settings before trying
to connect the camera.
15. The camera will now reboot. Please
wait for the app to countdown from 60
seconds
DO NOT REMOVE THE DATA CABLE
FROM THE CAMERA
16. Once the countdown stops, look for
the “Connected” to show next to your
network
17. Now you can disconnect the wired
ethernet cord and move the camera to its
desired location
WIRED SETUP
18. Open up the camera feed in your
Pyle IP app and you can check that it is
live!
Find desktop setup - feature overview
and product registration online!
www .pipcam wireless.com
WIRED SETUP
TROUBLESHOOTING
If the camera does not chirp and the loading bar times out - try the reset like in step 3
and try again
Make sure you have correctly entered the password for your home wireless router
If you have trouble multiple times with “One Key Conguration” - Do the reset in step 3 then try setup using the wired setup instructions
Pyle H.264 Solution Desktop Setup QSG
Find FAQs including setup video and support online at
http://www.pipcamwireless.com
This guide covers the following models
-PIPCAM8
-PIPCAMHD17
-PIPCAMHD45
-PIPCAMHD46
-PIPCAMHD47
Before you begin
*Setup should be done in the same room as the wireless router in your home.
* Camera and PC must share the same network. Verify the setup PC is on the
SAME network as the wireless router in your home.
1) Plug your camera into power
2) Attach the wireless antenna to your camera (If Applicable)
3) Plug your camera directly into your router with wired Ethernet wire
4) Wait 2-3 minutes for camera to boot
-You will see the camera run through a full range of pan and tilt motion.
-When boot up completes, your camera's Ethernet port will flash yellow and
green lights indicating the camera is connected to your router.
If you do not see the flickering lights - DO NOT CONTINUE
please refer to the FAQ online
https://pyleaudio.helpshift.com/a/pyle-ip/?s=general&f=the-green-and-yellowlights-at-the-back-of-my-camera-do-not-flash-when-plugged-into-power-andethernet
5) Copy/Paste or type the link below into your Internet browser to Download the
software package online
www.pyleaudio.com/manuals/drivers/pipcam8.zip
6) Unzip the zip file and select Mac or the other folder depending on your OS
7) Open the “IP Address Tool” folder and install the “SearchIPCam Setup” file on your
PC
8) Once installed – open the “S-CAM Finder” app
Click the “Refresh” icon to find your camera
No Camera Detected?
-Check again your PC and camera are connected to the same wireless network
-Verify you do not have any network security settings that will hide the network
-Try a hardware reset by holding in the camera reset switch for 10 seconds with a pin and
retry steps 1 – 4
9) Double Click the Http://XXX.XXX… address in the IP Camera tool or copy paste the
address into your internet browser
NOTE: Some users may see a blue background in the web UI – while the options may be
in slightly different places, the setup process is the same
10) Log in using your camera’s default user name and password
USER: admin
PASS: “pylecam” OR “admin”
11) Select the login option appropriate for your browser
-Google Chrome: Server Push Mode
-Internet Explorer: ActiveX Mode
-Safari/Firefox: VLC Mode
-I recommend using Google Chrome for fast initial wireless setup – to continue setting up
using Internet Explorer, skip to the link at the end of the guide to learn how to install the
Active X plugin – then resume step 12 for wireless configuration
12) Check that you see a live video feed for the camera
No Video?
-If you aren’t using Google Chrome – back up to step 9 and try logging in using Google
chrome in server push mode now
-Your login password may be incorrect – try both default passwords suggested step 11
-If still no video – do a hardware reset to make sure the camera password is set back to
default passwords
IE Issues
-Refer to main manual to check computer security settings
-Make sure Activex is installed
-Right click the Internet browser and click “Run as Administrator”
Now we can configure WiFi
1) Click the “Gear” icon along the top tab to access the camera’s settings
2) In the left column - click “Network Settings” > “Wireless Settings”
3) Click the “Search” button to display any wireless networks in range
No Networks Detected?
See FAQ online
https://pyleaudio.helpshift.com/a/pyle-ip/?s=general&f=i-don-t-see-any-networksdetected-when-setting-up-wifi
Or go to the FAQ on pipcamwireless.com and search the FAQ “I don’t see any
networks detected”
4) Click on your router’s name in the list – then enter your router’s wireless
password in the “Key” field – click “Save”
5) Allow the camera to load – wait for the countdown to run before adjusting the
camera or web browser
DON’T UNPLUG YOUR CAMERA POWER CABLE YET
5) Now let’s test the wireless connection in the same room as your wireless
router before moving the camera to the final location
-Leaving the power plugged in - Disconnect the wired Ethernet cable and wait
6) Wait 2-3 minutes for the camera to reboot
-I know - it doesn’t look like it is doing anything… But wait a bit before trying to
adjust the camera or refresh the app
PIPCAM5
You should see the white LED indicator go out as soon as you pull out the
network cable - after 1-2 min the LED indicator should come back on rapidly
flashing
Troubleshooting
If the camera does not connect wireless after 2-3 mins un-pluged from the data
cable - Reconnect the wired Ethernet cable and try
1) Setting the wireless password again
-Check password is entered correctly - Passwords are case sensitive - the app
will not give you “incorrect wifi password” indication
2) Try a hardware reset
Instructions available on our FAQ online
http://pyleaudio.helpshift.com/a/pyle-ip/?s=general&f=how-can-i-hardware-resetmy-camera
3) Try setting the password from the web UI
-Refer to desktop setup QSG
Additional setup
Please note that remote access to your camera via PC is not possible until you
set up DDNS and port forwarding in your router.
https://pyleaudio.helpshift.com/a/pyle-ip/?s=pipcam8-pipcamhd17-pipcamhd22pipcam24-pipcamhd45-pipcamhd82&f=how-to-configure-ddns---port-forwarding
Also online – find full instructions to set the following features
-Disabling the LED flashing indicator
-Recording
-Motion Detection
-3rd Party Apps
-Email Alerts
Don’t forget to claim your free 1 year warranty by registering your camera
with us online!
Find help and support with us online!
http://www.pipcamwireless.com
2
CONTENTS
1. INTRODUCTION ........................................................................................................................................... 4
1.1 Features ............................................................................................................................................ 5
1.2 Packing List ....................................................................................................................................... 5
1.3 Product Views .................................................................................................................................... 6
1.4 PC System Requirements ................................................................................................................. 7
1.5 Hardware Installation ......................................................................................................................... 7
2. INSTALLATION AND SETTINGS ................................................................................................................. 8
2.1 Network Connection ............................................................................................................................. 8
2.2 Browser Settings (For IE only) ............................................................................................................. 9
2.3 UPnP Service ..................................................................................................................................... 10
2.4 IPCam IP Address Search Tool (for IE browser only) ........................................................................ 11
2.5 Install the OCX ActiveX (For IE only) ................................................................................................. 12
3. SOFTWARE OPERATION .......................................................................................................................... 14
3.3 Functions .......................................................................................................................................... 16
3.4 For Live Video (for IE browser) .......................................................................................................... 17
4. SETTINGS .................................................................................................................................................. 26
4.1 Status----Device Info. ......................................................................................................................... 26
4.2 Setup .................................................................................................................................................. 26
4.2.2 Multi-Device Settings ...................................................................................................................... 27
4.2.3 Date & Time .................................................................................................................................... 28
4.2.4 Audio Settings ................................................................................................................................. 28
4.3 Network Settings ................................................................................................................................ 28
4.3.1 IP ..................................................................................................................................................... 28
4.3.2 Wireless Settings ............................................................................................................................ 29
4.3.3 Upnp Settings .................................................................................................................................. 30
4.3.4 DDNS Settings ................................................................................................................................ 30
4.3.5 P2P Settings ................................................................................................................................... 31
4.3.6 FTP Settings ................................................................................................................................... 31
4.3.7 E-mail(SMTP) Settings .................................................................................................................... 32
4.4 Video Info. .......................................................................................................................................... 33
4.5 Alarm Settings .................................................................................................................................... 34
4.5.1 Motion Detection ............................................................................................................................. 34
4.5.2 Alarm Settings ................................................................................................................................. 35
4.6 Record ................................................................................................................................................ 36
4.6.2 SD Card info .................................................................................................................................... 36
4.7 Cruise ................................................................................................................................................. 37
4.7 System ............................................................................................................................................... 38
3
4.7.1 Log .................................................................................................................................................. 38
4.7.2 Auto Maintain .................................................................................................................................. 38
4.7.3 System ............................................................................................................................................ 39
5. PLAYBACK for IE browser only .................................................................................................................. 40
6. FREQUENTLY ASKED QUESTIONS ......................................................................................................... 41
7. SPECIFICATIONS ...................................................................................................................................... 46
8. OBTAINING TECHNICAL SUPPORT ......................................................................................................... 47
Loading...