INSTRUCTION MANUAL
Models: PIPCAMHD46 | PIPCAMHD47
FAQs Video Resources Customer Support Available Online
www.PIPCAMWireless.com
OUTDOOR WIRELESS/WIRED HD P2P NETWORK CAMERA
(with H.264 image compression)
Don’t miss out! Claim your free 1 year warranty by registering with us online!
www.PIPCAMWireless.com
INTRODUCTION
This is an integrated wireless IP Camera. It combines a high quality digital Video Camera with network
connectivity and a powerful web server to bring clear pictures to your Desktop from anywhere on your local
network or over the Internet.
The main function of the camera is to transmit remote video over IP network. The high quality video image
can be transmitted with 30fps speed on the LAN/WAN by using H.264, MJPEG compression technology.
FEATURES
☆ Powerful high-speed video protocol processor
☆ High-sensitivity 1/3’’ CMOS sensor
☆ Picture total 1300K pixels (1.3 megapixel)
☆ Optical Zoom x4 - Pan and Tilt (PT) control, Pan 355°, Tilt 120°
☆ Optimized H.264 MJPEG video compression for transmission
☆ Multi-level user management and passwords definition
☆ Embedded Web Server for users to visit by IE
☆ Supports wireless network (WI-FI/802.11/b/g/n)
☆ Supports Dynamic IP (DDNS) and UPNP LAN and Internet (ADSL, Cable Modem)
☆ Motion detection alarm via email or app push notification
☆ Protocols：TCP/IP HTTP DNS DHCP PPPoE SMTP FTP SSL TFTP NTP
ARP/RARP NFS RTSP RTP RTCP.
☆ Supports WEP/WPA/WPA2 encryption
☆ Supports IE, Firefox, Safari, and Google chrome browsers
PACKING LIST
● IP Camera
● Wi-Fi Antenna
● User Manual & Quick Setup Guide
● DC Power Supply
● CD
● Network Cable
PIPCAMHD46/47 USER MANUAL
2
Camera Password Defaults
NOTE: Your camera will have 2 sets of username/ password
Mobile app
User: admin
Pass: pylecam
Web Login
User: admin
Pass: pylecam
*These passwords are not related – changing password in the app or the web UI only affects the password in
that interface.
If you forget your password – you can reset it back to default by performing a hardware reset
Hardware Reset
Plug your camera into both power and wired data and wait TWO MINUTES for the camera to completely boot
up.
• Wait until you see both green and yellow data light flickering
• Once the lights are active, press in the white button at the end of the wire harness for 15-30 seconds.
• You should see the camera respond with a flash in the yellow network light.
• Wait again for 2 minutes while the camera resets.
• You will know the camera has completed the reset once the yellow light has begun to flicker again.
• If you do not see the camera respond, then you probably are being impatient.
• Try as many times as it takes to get the camera to respond.
Camera Connection Cables
Audio Output: The jack is used to connect an external speaker or audio output device
Audio Input: The jack is used to connect an external microphone or audio input device
I/O Alarm Pins:
Alarm input (GND)
Input
Output A
Output B.
PIPCAMHD46/47 USER MANUAL
3
Network Interface: RJ-45/10-100 base T
Network Light: The green LED will be on when the network is connected, the yellow LED will blink when data
is transferred.
Reset: If you press and hold the RESET button for about 30 seconds, all the parameters will be set back to
the factory default settings. (Please keep the power on when doing a RESET).
Hardware Prep
Before you begin: Desktop or mobile setup should be done in the same room as your wireless router
1) Plug your camera into power
2) Attach the wireless antenna
Mobile Setup
Check FAQ Online
1. Download the App:
Download “Pyle IPCameraViewer” in Apple Store or Google Play
2. Check the camera is in wireless setup mode
- Reset the camera by pressing the switch in the camera cable bundle
Hold in the reset switch for 10 - 12 seconds. You may hear a faint click. Wait again 1 - 2 min for the camera to
reset and run through the full range of pan and tilt
3. Check in your mobile phone’s system settings that you are currently connected to your home router’s
wireless network
- Wireless Setup will not work using cell data
PIPCAMHD46/47 USER MANUAL
4
4. Open the Pyle IPCameraViewer app
Select the “add camera” button
5. Select the option for PIPCAMHD45/PIPCAMHD46
6. Select “Wireless Connection”
7. Scan the QR code located on the frame of the camera to automatically add the camera’s unique ID
8. Enter your home network's wireless password
PIPCAMHD46/47 USER MANUAL
5
9. Wait for the camera to load
Recommended! Select the option to change the camera password
Default Value: “pylecam”
PIPCAMHD46/47 USER MANUAL
6
You can change the password at a later time by pressing and holding the reset switch
If you do not get a successful connection
- Back out and double check you have correctly entered the password for your home wireless router (it is case
sensitive)
- Press and hold the reset switch before attempting pair again
Still having trouble? Let’s try the wired setup
Mobile Wired Setup Instructions
1) Delete the camera from the mobile app
2) Plug your camera into a wired Ethernet connection direct to your home’s wireless router
3) Confirm data is at the camera
- Wait 2-3 minutes for camera to boot. You will see the camera run through a full range of pan and tilt motion.
- When boot up completes, your camera's Ethernet port will show a solid green and blinking yellow light
indicating the camera is connected to your router.
4) When selecting the setup option in the app – choose “wired setup
Mobile App Interface and Features
Live Video Page
Use this page to manage all of the different cameras you have added to the app
- Tap the camera name to view it
- Swipe left to remove it from the app
Buttons
1) App Settings: Find FAQs/ Support
2) Dual View Mode: See two live feeds at once
3) Quad View Mode: See four live feeds at once
PIPCAMHD46/47 USER MANUAL
7
Camera View Page
Use this page to view a specific camera - access camera settings and enable features
Swipe right, left, up or down on the live view to activate your camera's PTZ
Pinch your fingers together to digitally zoom in
1) Camera specific advanced settings
2) Activate functions along the tool bar
- Swipe right to reveal more functions
Note: Different camera models support different features. You may see some options in the app that your
camera does support.
3) Change the camera playback quality
PIPCAMHD46/47 USER MANUAL
8
Snap: Takes a picture from camera - this will save to the phone memory not the SD
Record: Records the current live feed to phone memory - Does not work in the background
Call: Support for models with 2 way audio only - listen to the camera surroundings - push to talk through the
camera speakers
Zoom: Support for cameras with zoom lens only - You can control the optical zoom
Album: You can be able to check the snapshot and video here.
L~R: Activate camera left and right patrol
Arrows: Alternative to swiping the screen - control the camera PTZ
U~D: Activate camera up and down patrol
Swipe: Change the way swipe responds - you can invert the control direction
Use this screen to set and recall PTZ preset positions.
-Position the camera where you want to set preset while in the set tab
-Press the No. value you would like to overwrite
-Switch to the "Get" tab to recall the PTZ preset and quickly rotate the camera between your specified
positions
PIPCAMHD46/47 USER MANUAL
9
Adjust the camera brightness, contrast and hue settings
Advanced Settings
Access this screen to make changes to the settings detailed below
Name: You can set or change name for camera
Change camera password:
WiFi: You can set or change WiFi
Video Settings:
-Video Quality: Change between HD, Standard, Fluent, and Auto
-Video Orientation: For wall or ceiling installations you can flip the video orientation
-Video Environment Mode: Change between 50HZ 60HZ Outdoor
-IR Control: You will be able to turn on or turn off camera night vision LED
Time Settings:
Select your time zone - Enable Sync with Server - Select a server
Detection Settings
PIPCAMHD46/47 USER MANUAL
10
Once motion detection is enabled - you can make adjustments to the camera's sensitivity to trigger alerts.
Adjust higher if you do not receive alerts and lower if you are receiving false alarms.
Memory Card:
See the remaining space
Enable recording alarms to the memory
Turn on video "Auto-Overwrite" to overwrite old video when the memory becomes full.
Format Memory: Will overwrite all data - can be used if you need to troubleshoot memory cards
Volume Settings
Support for models with 2 way audio only - Make changes to the microphone sensitivity and the speaker
volume
Reboot and Reset
Can be used to troubleshoot issues
- Reboot camera, then camera will restart for 50 seconds.
- Reset factory settings, camera will default all data; then reboot for 50 seconds.
Camera Version:
You will see the current app version details here
Mail settings
Set up with a supported email provider and enable motion detection alerts to your email
Record Schedule Settings
Select the start and end time for recording - select the days of the week to record
PTZ setting
Adjust the sensitivity of the PTZ adjustment - high setting will have a more drastic effect
Recorded Videos to the Camera SD
After SD card is installed you can choose from the following recording options
1) Scheduled recording: Set the times you would like the camera to record
2) Motion detect recording: Record only when the camera detects motion in the environment
Setting Scheduled Recording
Go to the camera “Advanced Settings” > “Record Schedule Settings”
PIPCAMHD46/47 USER MANUAL
11
For 24 hour recording - select all the days and an end time 23:59
Or set the start and stop times and the days of the week to record
- You can find more advanced scheduling settings in the camera web UI
Setting Record on Motion Detection
Go to the camera advanced setting > Detection Settings
-Switch the setting from off
Go to camera advanced setting > Memory Card
-Enable "Capture alarms to Memory Card"
Playback Videos Recorded to SD
Navigate to the "TFCard" tab to see a list of all the cameras in your app containing SD video recordings
Select the camera name you would like to check - then the file name of the photo or video
PIPCAMHD46/47 USER MANUAL
12
You can then save the files directly to your mobile device
Desktop Setup
Please note: This manual covers desktop setup for use with the camera’s built in web interface. The camera
is also compatible with some 3rd party software. Please check the other options for desktop use on our
website online.
Other Desktop Setup
Web UI Setup
Online instructions
Before you Begin
*Setup should be done in the same room as the wireless router in your home.
*Camera and PC must share the same network. Verify the setup PC is on the SAME network as the wireless
router in your home.
1) Plug your camera into power
2) Attach the wireless antenna to your camera (If Applicable)
3) Plug your camera directly into your router with wired Ethernet wire
4) Wait 2-3 minutes for camera to boot
- You will see the camera run through a full range of pan and tilt motion.
- When boot up completes, your camera's Ethernet port will flash yellow and green lights indicating the
camera is connected to your router.
5) Load up the camera’s included software or download a copy from the link here
www.pyleaudio.com/manuals/drivers/pipcam8.zip
PIPCAMHD46/47 USER MANUAL
13
6) Locate the “IP Address Tool” folder and install the “SearchIPCam Setup” file on your computer
7) Once installed – open the “S-CAM Finder” app
8) Click the “Refresh” icon to find your camera
No Camera Detected?
-Check again your PC and camera are connected to the same wireless network
-Verify you do not have any network security settings that will hide the network
-Try a hardware reset by holding in the camera reset switch for 10 seconds with a pin and retry steps 1 – 4
9) Double Click the Http://XXX.XXX… address in the IP Camera tool or copy paste the address into your
internet browser
NOTE: Some users may see a blue background in the web UI – while the options may be in slightly different
places, the setup process is the same
10) Log in using your camera’s default user name and password
USER: admin
PASS: “pylecam” OR “admin”
11) Select the login option appropriate for your browser
-Google Chrome: Server Push Mode
-Internet Explorer: ActiveX Mode
-Safari/Firefox: VLC Mode
Loading...