WIRELESS SYSTEM
INSTRUCTION
MANUAL
POWER
DIVERSITY
A
B
AF
PEAK
PLL
Wireless Mic. Receiver
Diversity
ENGLISH
CHARACTER
SPECIFICATIONS
NAMES OF PARTS
INSTALLATION
POWER SUPPLY CONNECTION
SQUELCH CONTROL AND VOLUME CONTROL
UNBAL OUT AND BALANLED OUT
INDICATOR ANDINSTALL ANTENNA
NOTE
CONTENTS
NOTE
ENGLISH
RECEPTEUR :
40-60m
THE WIRELESS RECEIVER
2
2
3
4
4
5
6
7
8
RECEPTEUR
1m
1m
1m
LOCATED AT GOOD CONDITION
PLACE.
BE CAREFUL, DON'T DROP
OFF THE MICROPHONE TO
FLOOR.
Thank you for your kind using our wireless microphone
with receiver. Before using the machine please read
the instruction manual very carefully. According to our
instruction manual for ensure you using of the best
function and performance. lf any defect please contact
with our agent or dealer. lt is our pleasure to serve you.
Thank you for your cooperation
1
KEEP AWAY RAINING OR
SUN SHINE.
10
ENGLISH
NOTE
ENGLISH
Character :
UHF band frequency by PLL synthesized oscillator. Range from
780~865Mhz.
Compact, lightweight, single-channel receiver.
LED lndicator (Power , Diversity (A---B),Peak) and telescopic
antenna.
Compander circuit for expending dynamic range.
Special circuit design to delete microphone switch ON/OFF noise.
Audio output connect with XLR balanced and mono phone jack
unbalanced.
Specifications :
IF YOU ARE NOT TECHNICAL ENGINEER PLS. DO NOT MODIFIED OR KNOCK - DOWN IT.
9
Reception mode
Carrier Frequence Range
Oscillation Mode
Stabilite
Deviation maximum
Portee de dynamique
S/N proportion
T.H.D.
Squelch
Frequency Response
Sensitivity
Audio Output
Power Supply
Dimensions
Weight
Diversity model
UHF 780~865 MHz
PLL synthesized oscillator
0.005% /25 C
40/50KHz
>100 dBm
>100dB At 15KHz de Deviation
<1%
Tone Key (Tone frequency : 32.768KHz)
External Control
50Hz-15KHz 3dB
3uv pour 20dB SINAD
1. Unbalanced 6.3mm phone jack 750mV/5K
2. XLR Balanced output 70mV/600
DC 12V-15V 300mA
With AC/DC Adaptor
295(W) 114(D) 40(H) mm
0.97(W) 0.37(D) 0.13(H)ft
600g
1.32 lb
2
ENGLISH
ENGLISH
NAME OF PARTS
INSTRUCTION MANUAL
7. Indicator
4
POWER
DIVERSITY
A
B
AF PEAK
1
2
3
PLL
Wireles
Diversity
s
M
ic.
R
ec
e
iv
er
a. Power ON lndicator:
This red light glows. When
the DC supply and power
Switch ON. It indicates that
the receiver is on.
b. Reception Indicator:
This indicator does light
during standby. When
microphone signal is
received, The green or
yellow indicator light to
indicate the reception of
microphone.
c. Audio peak Indicator:
This red light flickers when
the audio signal from the
microphone approaches
the overload clipping level.
It is affected by the transmitter gain control setting
and the loudness of your
voice.
PO
W
E
R
FIG.7
DIVER
SITY
A
B
A
F
PEA
K
1. Power ON Indicator.
2. Mic. ON and Diversity Signal Indicators.
3. Audio Peak Indicator.
4. Telescopic Antenna.
3
SQUELCH
MAX.
SENS.
8. Squelch Control
This control is factory present,
SQ noisy controlled adjustment,
Before you turn-on the receirer,
at first. The receiver already
have been jamming by outside
signal. Please adjust SQ control until the jamming signal
has disappeared. (Clock-wise)
FIG.8
8
ENGLISH
ENGLISH
AUDIO OUTPUT
AUX
BALANCE
UNBAL
MICRO
IN
INSTRUCTION MANUAL
5. Audio Output Connector
You can connect an unbalanced audio cable with a 1/4
inch phone plug between this
connector and your mixer or
amplifier input.
FIG.5
AUDIO OUTPUT
AUX
BALANCE
MICRO
DC IN
-
+
POWER
ON OFF
6
5
5. Power Switch.
6. DC. Jacket.
NAME OF PARTS
SQUELCH
AUX
VOLUME
MAX.
MAX.
SENS.
9. Volume. Control.
10. Audio output Connector.
1
15
3
5
13
7
11
9
7
AUDIO OUTPUT
AUX
BALANCE
1089
MICRO
11
6. Balance output XLR or
CANNON Connection
Cable insert to balance soc-
ket output connecting with
mixer or amplifier MIKE IN.
7
MIKE INPUT
BALANCE
FIG.6
7. Channel selector switch.
8. Squelch Control.
11. Balance Socket.
4
ENGLISH
ENGLISH
INSTRUCTION MANUAL
1.Power Switch
Mark sure the correct voltage.
push this power switch once
to turn on; If unit still fails to
operate, Secure a qualified
technician or contact us for a
Return Authorization prior to.
Shipment. Disconnect power
supply before removivg receiver cover.
a different frequency, set the
receiver and transmitter power
SW to OFF before you do.
If you want to have
POWER
ON OFF
POWER
ON OFF
FIG.1
DC IN
-
+
INSTRUCTION MANUAL
3.Install Antenna.
Receivers signals from the transmitter. Make sure the antenna is
fully extended vertically.
4545
AUDIO OUTPUT
POWER
ON OFF
DC IN
+
-
1
15
13
11
9
3
7
SQUELCH
5
SENS.
AUX
AUX
BALANCE
VOLUME
MAX.
MICRO
MAX.
2.Power Supply Connection
Use DC power supply could
switch with adaptor supply or
batter of 12-18V DC.
Connection DC supply, DC
plug connection with "DC-IN"
socket. (see FiG2) another
plug terminal connection with
battery or power supply.
IN
4.Volume Adjustor
FIG.2
The purpose of this control is
to give the ability to provide
an audio outputlevel from the
wireless system that is similar
to that of a wired microphone.
5
6
AUX
VOLUME
MAX.
FIG.4
Loading...