www.PyleAudio.com
MINI 2X25W STEREO POWER AMPLIFIER
W/BLUETOOTH& W/USB CHARGING
FOR MOBILE PHONE
MODEL:PCA12BT
USER MANUAL
FOREWORD
PCA12BT
PCA12BT can be compatible with any mobi le device and computerized
devi ces (MP3) via 3.5mm to RCA converter.
FEATURES AND CONTORLS
FRONT PANEL
2X25W
1 2 3 4 5 6 7
1. POWER On LED Indicator
-Lights to indicate power is turn on or off.
2. Main Power on Switch
The amplifier is switched ON or OFF by using this switch.
-
1. Features and Cont rols
2. Caring for your Pyl e Amplifier
3.Troubleshooing
4. Limited Warranty and Specifications
3. USB Charge Port
USB port charges for smartphone, not for USB reader
-
function.
AU X / CD IN
4.
-Lets you easily connect the computerized MP3 Device
(player) sources, such as PC(
CD ROM),laptop, walkman,
iPod,and cell phone.
5. BLUETOOTH Indicator
When switches to Bluetooth mode, the indicator light will
-
be on.
When plays by Bluetooth mode, the light will flash.
-
6. Bluetooth/ Line input switch
Mode button switches between the Bluetooth and Line
-
audio inputs.
Pushed in
-
is for Bluetooth function, and pushed out is for
Line input.
7. Master Volume Control
-Lets you adjust the overall sound level, and turn the knob
clockwise to increase the volume.
2
BACK PANEL
8 9 10 11 12 13
8. Bluetooth Antenna
-Use of
antenna is best receiving for Bluetooth signal.
9.RCA Cable L/R LIN E Input
-
Lets you to connect the desired LINE input source.
10.Push Type Speaker L/ R Terminals
-
Let you easily connect the speakers'wires directly to
the amplifier
11.110V/220V Switch
-
According to power voltage, push this button to the
correct station of the 110V or 220V.
1. Be sure that the ampli fier is powered on. And it’s bet ter to pull
the Bluetooth Antenna on at the back of panel for better
receiving. Press MODE button on the front panel in like
situation, and the Bluetooth Indicator is l ight on. (The unit is
automatically ready to pair with your device)
2. Turn on the Bluetoo th function of your external device.
3. Search for availab le devices within range of your external
Bluetooth device.
4. Wait for a while then f ind the “TD301-RY” on the pai red
devices list on your external device and sele ct “TD301-RY”,
or find the “BT” on the paired devices list on your ext ernal
device and select “BT”.
5. Your amplifier will beep and the lights will flash once when
pairing is a success.
6. You can now play music and other audio on your external
device through your amplifier.
7. The amplifier will b eep and the lights will flash once again
when the external de vice is turned off or unpaired.
12.Fuse
-
The amplifier uses a
fuse for protection against surges
and short circuit. If the amplifier suddenly turn off and
will not turn on, check the fuse. If necessary, replace
it with a 1- amp, 250- volt, fast- acting, 5x20mm fuse
(not supplied)
13.AC IN Power Cord
-
Connect to AC 110V/60Hz or
220V/50Hz
BLUETOOTH FUNCTION INSTRUCTION
External devices w hich have a built‐in Bluetooth feature can be
connected to this amplifier wirelessly to play through the
amplifier’s speakers.
3 4
LIMITED WARRANTY
Sound source or speakers
may not be connected
properly.
Master volume control may
be set to a minimum.
The amplifier is shutting down
or powering off
5 6
Adjust the volume control to
a higher setting.
Make sure that the speakers
that you have connected to
the amp are matching in
impedance.
Turn the amplifier off and let it
cool, make sure that the amplifier
is properly ventilated, and then
turn it back on.
Output power, 2 channels driven
4-ohm, 1 KHz 1% THD. 15 Wx2
4-ohm, 1 KHz 10% THD. 10.1 Wx2
Peak Power 25 Wx2
Total Harmonic Distortion, 1 KHz Rated Power 0.3%
Input Sensitivity, 1 KHz, 4-ohm Rated Power 150mV
Frequency Response 20Hz-40KHz
Signal to Noise Ratio 75dB
Power Requirement 120V AC 60 Hz
or 230V AC 50Hz
Dimensions 5.6" x 2.6" x 4.2" inch
Loading...