Pyle PBC5200BK User guide

Pyle PBC5200

3G Wi-Fi Mobile Power Bank and Router Integrator

Quick Installation Guide

3G Wi-Fi mobile power bank and router integrator is a 3G network product for consumers, which

integrates 3G routing, wireless routing, ADSL dial-up Internet access, wireless network storage, mobile

power and other functions. This allows you to create a wireless network anytime and anywhere there is a

LAN connection. You can easily share contents in digital devices with others. Various functions of this

product are listed below:

 3G Routing: support 3G wireless network card dialing and bandwidth sharing for WCDMA / CDMA

2000 / TD-SCDMAstandard;

 Wireless routing: support traditional wired broadband ADSL dial-up, dynamic and static network

access;

 Wireless network storage: supports file reading and sharing on U disk, USB mobile hard disk, as

well as online video on-demand;

Mobile power bank: can charge iPhone, iPad, Android smart phones, tablet PCs and other mobile



digital devices;

 Wireless relay: relay and amplify the signals and thus extend the coverage ofwireless network.

Listofof

1.1.List

Thank you for buying the 3G Wi-Fi mobile power and router integrator. Please make sure your package

1. Host

2. USB charging cable

3. Quick Installation Guide /Warranty Card

4. Certificate

accessories

accessories

includes the following accessories.

-1-

Introductionofof

g

y

r

y

r

y

g

2.2.Introduction

Charg

ing

Indicator

Charg

ing

Indicator

2.1

Descriptionofof

2.1

Description

Hardware

Interface

Power switch

Battery indicator

button

USB interface

DC charging

interface

Charging

indicator

RJ45 network

port

Restore factory

settings

panel

panel

USB

port:

Connect

the

USB

port:

card,,

mass

card

mass

RJ45

RJ45

hardware

hardware

Identity Detailed Description of Functions

network

Connect

the

network

storage

device,oror

storage

device,

charge

the

phone

charge

the

phone

charging

interface

DCDCchargin

interface

network

cable

port

network

cable

port

interfaces

interfaces

R Turn on the powerswitch to R to start the router function

Charging, switch to C to activate the mobile power bank function to

C

charge devices through theUSB port

Off switch

Press this button, the battery indicator will show the current battery,

battery indicator is dividedinto four levels.

This interface can connect 3G USB modems, U disk, USB mobile

hard disk, flash drive, or connect smart phones, tablet PCs, PSP

and other digital terminalsfor charging.

DC 5V input, you can charge the unit through the Micro USB

charging cable.

When the unit is beingcharged, the indicator is always on

WAN port: In the mode of Dynamic IP/Static IP/PPPoE, the port is

used as a WAN port to connect a wired network, LAN broadband,

xDSL Modem/Cable Modemof hotels.

In Routing state, long press for 5 seconds, then release the key,

the router will restore tofactory settings.

-2-

Battery

Batter

Battery

Batter

Restore

Restore

Power

Power

R:R:Power

Charging

CC::Charging

indicator

indicato

indicator

indicato

factory

factor

Switch

Switch

Power

0:0:OOff

ff

button

button

settings

settin

s

2.2

Descriptionsofof

2.2

Descriptions

Action

Performed

Turn On the

power

Removable

storage
inserted

Equipment

3G card
inserted

Insert ADSL

network cable

(PPPOE Mode)

Network cable

plugged into

the router

(Dynamic IP

mode)

Network cable

plugged into

the router

(Static IP mode)

Status

Status

Indicator

status

Blue light

always on

Blue light

flashes slowly

(1.5 seconds

each time)

Blue light

always on

Blue light

flashes quickly

(0.5 seconds

each time)

Blue light

flashes slowly

(1.5 seconds

each time)

Blue light

always on

Green light

always on

Blue light

flashes slowly

(1.5 seconds

each time)

Green light

always on

Green light

flashes slowly

(1.5 seconds

each time)

Green light

always on

Indicators

Indicators

Details

Slide the power switchto C to power on unit

When U disk, mobile hard drives and other removable storage

devices are plugged in to the USB port, you can see the blue

light flash slowly after 8-10 seconds, indicating that the

removable storage devices are loaded normally and can be

accessed.

Removable storage devices arenot loaded successfully

When 3G USB modems are inserted, you can see the blue light

flash quickly after about 30 seconds (0.5 seconds each time),

indicating the router isin the 3G dialing state;

Blue light flashes slowly (1.5seconds each time), indicating that

the router has dialed-up via 3G successfully, and you can

access the Internet.

Dial not successful

With the Ethernet cable plugged in, if you can see the green

light is always onafter 5 seconds, this indicates thatthe network

connection is normal;

After green light is on for a while, if you see the blue light flash

slowly, this indicates that the router ADSL has dialed-up

successfully,and you can access the Internet

Indicates that the network cable is connected properly

Indicates that network cable is connected properly, also

meaning that the router has successfully retrieved IP addresses

dynamically assigned on the upper router.

Indicating that the network cable is connected properly

-3-

3. Application scenarios

The product supports the following application modes:

1) 3G to WiFi InternetSharing mode

Plug 3G USB data card

2) Wired to WiFi Internet Sharing mode

Gas ADSLmodem / router

3G to wifi mode

Wired broadband to wifi mode

-4-

Mobile

power

function:

4.4.Mobile

tablet

tablet

Step 1: Battery display.

Before charging mobile phones, tabletcomputers and other digital products, check the battery level of the

device itself, and followthese instructions:

a) Press the battery indicator button. The battery indicator light should turn on and you can see the

b) The corresponding relationship between batteryand power indicator:

power

computers

computers

current battery percentage.The light will turn off automatically when idlefor more than four seconds in

order to save power.

Battery

level

indicator

and

and

Instructions

function:

Instructions

other

digital

other

digital

LED status Details

No lights

One light is on Capacity is less than 25%

Two lights are on Capacity is between 25% -50%

Three lights are on Capacity is between 50% - 75%

Four lights are on Capacity is between 75% - 100%

for

charging

for

charging

products

products

No electricity, please charge this unit

first

mobile

mobile

phones,

phones,

Battery level

indicator

(divided into

four)

(Battery schematic diagram)

Step 2: Charge mobile phones, tablet computers andother digital products.

Set the switch to the charging function (C) position to activate mobile power function, and then connect

the charging cable of digital products to the USB port of this product. This unit can charge iPad, iPhone,

-5-

Press the "z"

button, you can

display the

current battery

charge

Android smart phones, andother mobile digital devices.

Tip: Use originalcharging cable for cell phones to achieve thebest results.

Charge various

devices via this

USB port

(Schematic

diagramofof

charging

(Schematic

diagram

Charge

this

5.5.Charge

When the battery has beenexhausted, you can charge it in the following two ways:

 Power Charging: Connect one end of the Micro USB charging cable to the DC charging port of this

product (Micro USB Interface)and connect the other end to the USB port ofcharging adapter.

Computer USB Charging: Connect one end of the Micro USB charging cable to the DC charging



port of this product (MicroUSB Interface) and connect the other end to thec omputer's USB port.

Please connect

the smaller end

of Micro USB

charging cable

to this interface

product

this

product

(Schematic diagram of chargingthis 3G Wi-Fi unit)

charging

devices)

devices)

-6-

Charging Precautions:

1. Please choose thecharging adapter where the output is 5V (output current is between 600 to 1000mA)

Common charging adapters, suchas adapters for iPhone or iPad, can be used.

2. Charging time: it will take about 5-8 hours with a charge of 5V 1000mA; 11hours with a charge of 5V

600mA;

It will take more than 12 hours if it is directly charged using a computerUSB.

3. In the processof charging this unit, do not reusethe unit to charge other equipment, inorder to protect

the battery and prolong batterylife.

Features

and

6.6.Features

3G Wi-Fi router supports access and configuration through a web browser. You can use common

browsers, such as Microsoft's IE browser, Apple's Safari browser and the built-in browser of any Android

operating system. Login to the router, browse contents of mobile storage, and configure the router

parameters.

6.1

The

6.1

The

example,

example,

Step 1: Open the main interface of the iPad, select "Settings"  "Wireless LAN", enter the Wi-Fi settings

page. Turn on the wireless network switch, iPad will automatically scan surrounding wireless networks,

and you will see the id 3G Wi-Fi xxxx, double-click to connect.
Step 2: When connecting, enter the Wi-Fi password behind the router enclosure, and make the

connection (the password canbe modified yourself)

If connected successfully, a tick “ ” will appear to the left, while at the same time there will be a sign

join the network, please m ake sure your wireless password is entered correctly.

configurationsofof3G3G

and

configurations

The

followingisisanan

following

iPad)

iPad)

wireless

wireless

introductiontoto

introduction

device,

device,

The

use

your

use

your

at the upper left corner of the screenindicating a successful connection. If promptedyou can not

you

you

the

the

needtoto

need

Wi-Fi

Wi-Fi

operationofof

operation

connecttoto

connect

-7-

wireless

wireless

this

unit.

this

unit.

the

the

router

router

wireless

wireless

router

router

first

first

(for

(for

Set up

Flight mode

WirelessLAN

Notification Open

Location Service Open

Brightness and Wallpaper

Digital Photo Frame

General

Mail, Contacts,Calendars

Wireless LAN

Select a Network…

WirelessLAN

Video

Photo

Other…

Ask to Join Networks

Memo

Applications

Step 3: View and set network parameters. Click the ">" button atthe right of where it says connected, and

the setting page forwireless connection network parameters pops up (By default, DHCP server is enabled

by the router, it is recommendedto use DHCP).

The computer will beautomatically added to a known network,

if the network is notknown, it prompts to ask if you want to

join a new network

-8-

Set up

Flight mode

WirelessLAN

Notification Open

Location Service Open

Brightness and Wallpaper

Digital Photo Frame

General

Mail, Contacts,Calendars

Video

Photo

Memo

Applications

6.2

Enter

the

6.2

Click the Safari browser, enter: http://192.168.169.1, in the address bar. Click the "Go" button to enter the

In addition, for users of iPhone and iPad ios devices, there is a more efficient way to enter the router

configuration page. You can directly enter "wd" in the Safari browser's address bar. Then, you can go in

by clicking the "Go" button.

configuration

Enter

the

configuration

homepage of the router configuration page. See below:

IP address

Static IP

Subnet Mask

Router

Search Domains

Client ID

HTTP Proxy

interface

interface

Ignore this Network

Renewal

Close Manually

for3G3G

Wi-Fi

router

for

Wi-Fi

router

-9-

Automatically

6.3

Homepageofof3G3G

6.3

Homepage

common

common

functions

functions

router

router

operation

operation

configuration

configuration

interface

interface

interface––

interface

Descriptionofof

Description

functionsinin

functions

You canchoose a suitable network connection type according toyour network

User interface for common functions

environment, and set parametersfor different types of network connections

Multimedia

Wifi Security

Please choose the righttype of network connection according to your currentInternet environment

Icons of the first row:

: Click on this icon, you can enter the 3Gconfiguration page;

: Click on this icon,you can browse and play multimedia files onmobile storage devices.

: Click on this icon, you can enter the WiFi security settings interface. Here, you can change the

WiFi password.

: Click on this icon, you can enter the router's advanced setup interface. Here, you can set up

more features of the router, such as upgrading firmware, checking status, and so on.

browser

Dynamic

(obtain IP

automatically)

Settings

Static (fixed IP)

-10-

Advanced Settings

Second row icons:

: Click on this icon to enter the setting interface for dynamic IP Internet. This will pop up at the

bottom of the page. If your current Internet environment is through a wired network cable (Hotel

Internet typically uses this method), then theIP address is assigned by the upper router. Please

click on the "OK" buttonto complete the setting; otherwise click "Cancel."

: Click on this icon to enter the setting interface for PPPOE dial-up. This will pop up atthe bottom

of the page. If yourcurrent Internet environment is through a wired networkcable or a telephone

line dial-up, then, please first enter the user name and password of the PPPOE dial-up, and

then click the "OK" buttonto complete the setting; otherwise click" Cancel."

: Click on this icon to enter the setting interface for staticIP Internet. This will pop upat the bottom

of the page. If your current Internet environment is through a wired network cable and the IP

address is manually specified, then enter the addresses of IP address, subnet mask, gateway,

and DNS domain name in each column. Then click the "OK" button to complete the setting;

otherwise click "Cancel."

: Click on this icon to enter the setting interface for W iFi repeater mode. This will pop up at the

bottom of the page. Click "Search all AP", and then check the SSID you want to relay. Enter the

password and click OK.

6.4ToTo

modify

Wi-Fi

6.4

modify

WiFi router's factory-set password is relatively simple. When you first use this product, remember to

modify the WiFi password toensure data security.

Modification method:

Click on "WiFi Security" icon,enter the setting page for WiFi security.

Wi-Fi

passwords

passwords

-11-

Language

Network Settings

Wireless network settings

Basic Settings

Security Settings

Client List

DHCP server

Network sharing

System Management

Tip:

a) In order to preventyour wireless network from unauthorized access by others, we recommend setting

up wireless encryption. The recommended encryption method is WPA-PSK/WPA2-PSK.

b) After setting the wireless network SSID and encryption, please connect the wireless network again.

The WiFi password hasnow been set.

6.5.ToTo

set

6.5.

set

When users insertthe 3G modem into therouter's USB port, the router will automatically begin3G dial up.

When 3G dials-up, the systemneeds to call some configuration information. So please configure them in

the 3G configuration page beforeinserting the 3G modem.

Click the "3G" icon toenter the 3G setting interface, select "3G networkcard model", and in the dial

setting, select "dialing on start mode", type "dial-up parameters" provided by3G ISP, and click "OK".

Wireless network security/encryption settings

Set up a wireless network security/encryption to prevent unauthorized
device access

Safe Mode

WI-FI ProtectedAccess

WPAencryption algorithm
Password

Private key update cycle

Status

Home

parameters

parameters

for3G3G

for

Internet

Internet

OK Cancel

-12-

By default the system isin automatic recognition mode, plug and play, usersdo not need to do any

modification.

Normally, you only need toselect "Auto Detect" (automatic identification) for "USB3G Modem" Model on

the interface shown in the above figure, which can automatically set the dialnumber, APN user name and

password and other information.This way, you only needto connect 3G modem to the router's USB port,

and there’s no need todo any setting before completing 3G dialing.

3G network connectionsettings

You can set the appropriateconnection parameters
according to your local 3G network environment

3G model
USB 3G modem
Current status

Dial settings

Connected

Disconnected

Permanent connection

Start

If there’s notraffic inspecified minutes,then disconnectdialing

dialing

Dial-up parameters

(Default, Custom)

OK Cancel

-13-

6.6ToTo

set

the

6.6

In wired Wi-Fi mode, 3GW i-Fi is equivalent to awireless router, the Ethernet port works as WAN port, all

of the wireless terminalsonly connect to the Internet via Wi-Fi router.

Click the "Network Settings"→ "WAN", choose the way to access theInternet according to the front-end

broadband lines, and the router supports three kinds of common wired Internet: static IP, dynamic IP,

PPPoE.

a) Static IP

If the network provider provides the way of static IP for your access to Internet, you need to enter the

IP address, subnet mask, gateway, DNS server, alternate DNS server provided by your ISP or

network administrator.

b) Dynamic IP

If the network provider provides the way of dynamic IP for your access to Internet, you do not needto

make any settings here. Just click "OK". Dynamic IP is the method of accessing Internet commonly

used in hotels and restaurants and other public places.

c) PPPoE

If you access internet by "ADSL virtual dial-up" approach, you only need to type account information

provided by your ISP in the "User Name" and "Password" input boxes, and after that the setup is

parametersofof

set

the

parameters

Static mode

IP address

Subnet Mask

Gateway

Primary DNS server

Alternate DNS server

DHCP mode

Network Name

wired

broadband

wired

broadband

OK Cancel

OK Cancel

-14-

Internet

Internet

access

access

complete, click "OK".

PPPOE mode

User Name

Password

Confirm Password

Manually

Run Mode

OK Cancel

d) Wireless Repeater

If you want to use the "Wireless Repeater" mode, simply check the "wan WiFi modes" item, click

"Scan all AP", then select the name of the wireless network interface you want to relay, enter the

password and click "OK"button.

-15-

6.7

(

Basic

settingsofof

WiFi

wireless

6.7

Basic

settings

Click on the left menu bar, "Wireless Network Settings" -> "Basic Settings", you can make basic wireless

network settings of network mode, SSID, wireless channel, and others.

WiFi

wireless

network

network

Language

Network Settings

Wireless network settings
Basic Settings

Security Settings
Client List

DHCP server
Network sharing

System Management

6.8ToTo

6.8

Router supports upgrading firmwarethrough the browser.

There are two methods of upgrading firmware as follows:

1) Upgrade firmware via LAN

This method can only be used to upgrade the firmware on Windows PC and notebook computers.

Steps are as follows:

Click the "Select Files button," locate the name of the firmware to be upgraded in the pop-up file

selection box, after that,click "OK" button to begin the upgrade.

2) Upgrade firmware via a USB storage device (U disk or SD card)

Please use the browser to log into the router (You can use browsers of PCs, smart phones, tablet

computers to operate), in the left menu, select [System Management] - [Firmware Upgrade], and

Basic Wireless Settings

You canmake basic wireless communication settings, such as:network name

Service Set Identifier)and channels

Wireless Network

Network mode

Network name (Service Set Identifier)

Broadcast networkname (Service Set Identifier) Enable Disable

Basic ServiceSet Identifier

Frequencies (channels)

Status

Home

upgrade

firmwareofof

firmware

wireless

wireless

upgrade

Select automatically

router

router

-16-

OK Cancel

then plug a U disk / TF containing the upgrade file i nto the socket of the router, then click the [scan]

button on the userinterface, select the file you want to upgradei n the drop-down box, and click [OK]

button.

During the process of upgrading firmware, theindicator light of the router will flash quickly and constantly.

While it is flashing, please do not turn off power of the router until the router's indicator goes off. After

router upgrade is complete, it will cause the router to restart. Then, your wireless device may need to

re-search the device andreconnect manually.

Specific process is shown below:

Firmware Update

Language

Network Settings

Wireless network

settings

DHCP server

Network sharing

System Management

Management

Firmware Upgrade:

Settings Manager

Status

Statistics

Updating routerfirmware can add new features. Please copy the firmware forupdate to
the flash drive, U diskor SD card. Theninsert U disk/SD/flash drivecard into the device,
and then click the [Search]button. After you seethe name of theselected firmware file,
click the [OK]button to start theupgrade.

The process offirmware update will take about1 minute, please wait patiently.
Warning, abnormal firmware willinterrupt the normal operation of system.

Updating the firmware from theUSB Disk

Location

OK Search:

Step 1

Step 2

Status

Home

-17-

Firmware Update

Language

Network Settings

Wireless network

DHCP server

Network sharing
System Management

Management

Firmware Upgrade:

Settings Manager

Status

Statistics

7.7.ToTorestore

If we modify some of the parameters of the router, it may cause some problems when we use the router.

For example, we modify the router's WiFi password, but after a period of time, we forget this password. If

that happens, please manually restore the wireless router's parameters to the factory defaults, concrete

steps are as follows:

Updating routerfirmware can add new features. Please copy the firmwarefor update to
the flash drive, U diskor SD card. Theninsert U disk/SD/flash drivecard into the device,
and then click the [Search]button. After you seethe name of theselected firmware file,
click the [OK]button to start theupgrade.

The processoffirmware update will take about1 minute, please wait patiently.
Warning, abnormal firmware willinterrupt the normal operation of system.

Updating thefirmware from the USB Disk

Location

OK Search:

Step 4

Status

Home

restore

the

factory

the

factory

configurationofof

configuration

-18-

the

the

wireless

wireless

router

router

Step 3

Use a small needle, for example a paperclip, insert the

y

paperclip into the hole indicated by the arrow, when

you feel that it may contact the switch inside the unit,

give the paperclip a push with force and hold it for 5

seconds, then release the paperclip, after that you can

see the blue light flash which indicates the restoration

to factor

set is successful.

The

functionofof

wireless

network

storage:

the

way

iPad

and

other

8.8.The

function

wireless

network

storage:

the

way

iPad

access

theUU

diskoror

mobile

hard

media

media

hard

disk

disk

-19-

access

the

disk

mobile

3G Wi-Fi provides a USB interface to connect to Flash drives, Udisk, or mobile hard disk reader,etc., and

supports the shared access of contents of these storage devices wirelessly. For example, you can use a

third-party media software to play, upload, download shared files onUSB storage device on iOS platform,

such as: iTunes,Goodplayer, OPlayerHD, TIOD, Aceplayer.

Router provides three ways to access Flash drive disk or mobile hard drives and other storage devices,

steps of wireless storageaccess are as follows:

8.1

Online

playofof

play

streaming

streaming

8.1

Online

Step 1: Plug U disk, mobile hard drives and otherUSB storage devices into the router's USB port.
Step 3: Open the router's power switch, and after the router starts, check the blue LED status indicator of

the router.
Step 4: Open iPad Wi-Fi settings, select SSID of 3G WI-FI equipment, and connect to wireless network

(refer to the previous section)
Step 5: Click the Safari browser, type: http://192.168.169.1 or "wd" in the address bar, click the "Go"

button, then click on "Multimedia Browse"i con to enter the mobile storage device file browser page of the

router, where you can quickly access pictures, videos, music and other files inside the U disk or mobile

hard disk.

and

other

devices

devices

Removable storage devicefileanddirectory browsing

Current Location: /media

List of files and directories

Return

Name Modified Time Size

Return

The storage1, storage2 ... arenames of the shared folders of U disk, mobilehard disks.

8.2

FTP

Server:

8.2

FTP

Server:

The following describes how to use the iPad to share files on the FTP server of the router, here we cite

Goodplayer as an example. GoodPlayer is not only a local media player, but it is an integrator of

"Movie Player & Downloader & Streaming Media Player." In fact, as long as shared media files are

transferred to your iOS device via Wi-Fi, you canimmediately play them.

Step 1: Enter theApp Store, search for "Goodplayer" program, then downloadand install the program.

Cancel Search

Category Price Device Reset the filter

Entire Entire Entire Clear all

Did you wanttosearchmoreplayer?

Ipad App

1-2, total of 2, Show All Sorted by:Relevance

GoodPlayer

Entertainment

Updated onSeptember 11,2012



528 ratings

Step 2: Open Goodplayer, switch to the W i-Fi interface, and click icon at the right corner of the

bottom.

-20-

Step 3: Select the FTP client

Download Manager,browser

Complete Media URL

SMB/CIFS Client

UPnP/DLNA Client

WebDAV Client

FTP Client

SFTP Client

Step 4: Click the button at the upper right corner, enter parameters of the FTP server, click the
"Save" button at the upperright corner.

-21-

FTP Server

IP address

User name

Password

Port number

Encoding format

Passive mode

 IP Address: 192.168.169.1
 Username: admin

Password: admin



Port Number: You can customize the value, and the default value is 21.



Step 5: Back to main program interface of Goodplayer, click on the FTP server just added [FTP]

192.168.169.1

FTP Server

The storage, storage1, storage2.... shows up after clicking

storage1, storage2 ... are names of the shared folderson U disk, mobile hard disk.

Step 6: If you click on a file separately and choose to play this URL, the file will immediately be played; if

you choose to downloadthe file, the file will be downloaded onto theiPad.

-22-

Shared Folders

9200 data

Double LAN ports

Download

Play this URL

Copy Link

Cancel

Note: The above is only a simple introduction for Goodplayer to play files via Wi-Fi, if you need more

details, please visit Goodplayer’s online help documentation.

Goodplayer  Settings  upper right corner button  Online Help

8.3Server

8.3Server

The following describes how to use the iPad to share files on the server. Here we cite OplayerHD Lite as

an example. OPlayerHDcan be used to enhance the mediaplayback capability of your iPad, you canalso

use it to play streaming media on the network, and now it supports http protocol. Currently supported file

formats are mp3, wma, wmv, avi, flv, rm, rmvb, mp3, 3gp, mkv, etc.
Step 1: Enter the App Store, search for "OplayerHD Lite" program, then download and install that

program.
Step 2: Open OplayerHD Lite, switch to the file server interface and click the button next to the "+".

-23-

File server

My Documents

Open URL

Step 3: Select the Windows Server and enter the address, authentication and other parameters of the

server. Click the"Save" button at the upper right corner.

Close

Add Server

Windows Servers

FTP Server

Dropbox

Document Management

WIFI transmission

 IP Address: 192.168.169.1
 Port: 139 (default value)
 Username: admin

Add Server

Add Server Add Windows Servers Save

Server Address

Server Address

Port

Authenticate

User name

Password

Server Name

Name

-24-

 Password: admin

Step 5: Back to maininterface of OplayerHD Lite program, click the- server just added 192.168.169.1

File server Edit

My Documents

Open URL

Download of the file list is finished

Step 6: Open Share  Storage, Storage1, Storage2 ... sharedfolders, and click a specific file.

File server Edit

My Documents

Open URL

Tip: For more information about the software, you can view OplayerHD help documentation, read
frequently asked questions.The lower right corner "···" button  Help  FAQ

Retreat

-25-

9. Solutions for Frequently Asked Questions

1. What can I doif I forget the WiFi encryption key?

Press RESET to restore therouter to factory settings, for details please refer to Section 7.

2. What do I doif I cannot log on to the router managementinterface?

1) Check if the IP address and DNS address are set to be obtained automatically. Normally the IP

address obtained should be192.168.169.X.

2) Tryusing another computer to log on;

If the problem is still not resolved after the above operations, try to restore the router to factory

settings.

3. What can I doif the notebook can not find the wireless signal?

1) Check if the built-in wireless LAN switch of the laptop is turned on (For details, please view laptop

manual);

2) Open the Device Manager of the computer, and view if the wireless network adapter driver is

successfully installed andenabled;

3) Check if the computer's wireless service is turned on (Check if the status of Wireless Zero

Configuration in the service option is set to Start, andif Startup Type is set to "Start automaticly”);

4) Tryto find the wireless signal within a 1-2m distance.

5) Please useanother computer's wireless adapter to find the wirelesssignal;

If the problem is still not resolved after the above operations, try to restore the router to factory

settings.

4. How do I clearthe previous network configuration with Windows 7 andApple iPad?

Windows7: Network and Sharing Center—Manage wireless networks, select the corresponding

wireless network name, and dodelete operation;

iPad: Navigate to Setting --- Wireless LAN --- corresponding wireless network name, ignore (or foret)

this network option above theright blue arrow, and click Ignore.

5. How to view therouter software and hardware version?

In the management interface,click on

"Advanced Settings" button toview.

-26-