Page 1
Page 2
For the best results and the satisfaction from your new unit, please
read this manual thoroughly, and retain it for future reference.
ATTENTION
To avoid the possibility of malfunction/damage to the product, damage to
data, or damage to other property. Please follow the points as below.
OPERATION AND MAINTENANCE
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Otherwise, the device, TV, or radio may generate
noise.
• In order to prevent the possibility of panel disguration, unstable operation, or
damage to the internal components. Do not expose the device to excessive dust
or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or
in a car during the day).
• Do not place vinyl, plastic or rubber objects on the device, since this might
discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,
solvents, cleaning uids, or chemical impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic changes in ambient
temperature when the device is moved from one location to another, or aircon ditioner is turned on or off. For example, using the device while condensation is
present can cause damage. If there is reason to believe that condensation might
have occurred, leave the device for several hours without turning on the power
until the condensation has completely dried out.
• Avoid setting all controls to their maximum. Depending on the condition of the
connected devices, doing so may cause feedback and may damage the speakers.
• When turning on the power in your audio system, always turn on the power
amplier LAST, to avoid speaker damage. When turning the power off, the power
amplier should be turned off FIRST for the same reason.
www.PyleUSA.com
2
Page 3
PRECAUTIONS WHEN USING THE USB 2.0 AND 5V DC TERMINALS
Precautions When Using the USB 2.0 and 5V DC Terminals. When connecting
the USB 2.0 connector to computer, please must abide following points. If not,
it may cause computer crash, breakdown or losing data. If the computer or
mixer crash, rstly restart the application software or computer operating
system or disconnect the mixer, then power on again.
• Use an AB type USB cable. USB 3.0 cable cannot be used.
• Before connecting the computer to the USB 2.0 terminal, exit from any power-
saving mode of the computer (such as suspend, sleep, standby).
CONTROLS AND FUNCTIONS FOR PAD12MXUBT - PAD22MXUBT
1
2
3
5
4
6 7 8
11
1. [MIC/LINE & GUITAR] Input
jack, this combo jack can be
used to connect the mono
20
signal such as XLR microphone
22
or 1/4” line input device, or
connect with an instrument
19
such as an electric guitar or
an electric bass, they need to
be converted with SWITCH .
2. [MIC/LINE & GUITAR]
14
Converting switch, for conver-
16
ting the different input source.
13
Press down this switch to
connect with a high impe-
12
dance audio source, such as
electric guitar or bass. When
the switch is bounced up, it
connects with XLR microphone
or 1/4” low impedance audio
device.
www.PyleUSA.com
3
Page 4
3. [LINE IN] Controller, used to
adjust the volume from RCA
LINE IN input.
4. [CH 1/2/3] Controller, used to
adjust the volume of signal
input of CH1/2/3.
5. [PEAK] LED indicator light, it
will light up when the input
signal is too high.
6. [PHANTOM +48V] Switch,
used to activate the phantom
power supply on XLR connector,
it offers +48V phantom power.
7. [PHANTOM POWER]
LED, indicates the phantom
power is on.
8. This is an input select switch, when the switch is bounce up, the input signal is
from LINE IN. Press it down, the input signal is from USB/BT.
9. This is an input select switch, when the switch is bounce up, the input signal from
stereo CH 2/3 and AUX IN. Press it down, the input signal is from USB/BT.
10. This is a converting switch for MIC/LINE inputs:
a. When it is bounce up, it is for STEREO input, connect MIC/LINE CH 1 (L) and
MIC/LINE CH2 (R) inputs, CH 1 (L) is channel L, MIC 2 (R) is channel R,
compose to the stereo signal.
b. Press it down, it is for MONO input, the signal of CH 1 and CH 2 are separately.
www.PyleUSA.com
4
Page 5
11. [MAIN] Controller, used to adjust the volume of MAIN and USB PORT output.
12. [CLIP] LED, it will light up when the MAIN output signal is too high.
13. [POWER ON] LED, it will light up when the mixer’s power is on.
14. [PHONES] 3.5mm output jack, connect with earphones, it is supporting stereo
phone plug.
15. [PHONES] 6.35mm output jack, connect with earphones, it is supporting
stereo phone plug.
16. [PHONES] Controller, control the volume of earphones.
17. [AUX IN] 3.5mm jack, this is an auxiliary STEREO input, exible connectivity for
a variety of external audio devices.
18. [STEREO IN] 3.5mm jack, this is an auxiliary stereo input, exible connectivity
for a variety of external audio devices. The volume can be controlled by
external audio devices or MAIN controller.
19. [BT/USB] Convert switch, when the switch is bounce up, it connect with
Wireless BT. Press it down to connect with USB.
20. [LINE IN] Stereo RCA input jacks, connect an audio source with line signal
level, such as CD player, tape deck etc.
21. [CH 2/3 STEREO INPUT] Jacks, for connecting to line level device (e.g. electric
keyboard) via 6.35mm plugs, if only connect to L (MONO) jack, the mixer will
send out the same mono signal to L and R outputs.
22. [MAIN MIX] Stereo RCA output jacks, connect the input of an amplier or a
recorder.
23. [MAIN] Stereo 6.35mm output jacks, connect the input of an amplier or a
recorder.
www.PyleUSA.com
5
Page 6
CONTROLS AND FUNCTIONS FOR PAD33MXUBT - PAD43MXUBT
1. [MIC/LINE] Input jack, used to
3
1
2
4
9
10
11
13
12
16
4. [2-TK] Stereo RCA input jacks, connect the audio source with line signal level,
such as Recorder, MP3 player etc.
5. [MAIN MIX] Stereo RCA output jacks, connect the input of an amplier or a
recorder.
6. [POWER ON] LED, it will light up when the mixer’s power is on.
7. [BT/USB] Convert switch, when the switch is bounced up, it connects with
Wireless BT. Press it down to connect with USB.
8. This is an input select switch, when the switch is bounce up, the input signal is
from 2-TK. Press it down, the input signal is from AUX IN.
5
connect the mono signal such
7
as XLR microphone or 1/4”
6
line input device.
2. [+48V PHANTOM POWER]
8
Button/LED, when the button
14
is turned on, the LED light is
15
on, provide DC +48V phantom
19
power to XLR plug on MIC
20
mono input. Please turn on
22
this button when using the
23
condenser microphone which
17
is powered by a phantom
power.
24
3. [LINE IN] Stereo RCA input
18
jacks, connect the audio source
with line signal level, such as
CD player, tape deck etc.
www.PyleUSA.com
6
Page 7
9. [GAIN] Controller, determines the basic volume of CH1/2, adjust it for maximum
volume performance, when the volume gets too loud, the PEAK LED indicator
will keep ashing.
10. [HIGH & LOW] Tone controller, adjust the high frequency and low frequency
for CH1/2.
11. [PAN] Controller, this is the panorama control or balanced control, determines
the position of channel signal within the stereo image. When working in sub groups, you can use the PAN controller to assign the signal to just one output,
which gives you additional exibility in recording situations.
10
11
13
1
3
5
4
7
6
2
8
14
15
9
19
21
22
23
17
24
18
12
16
www.PyleUSA.com
7
Page 8
Set this controller in middle position, signal level of channel L & R will be same.
When the controller is set to top stop, only Channel L receives the signal, and
not Channel R, vice versa.
12. [CH1/2] Controller, used to adjust the volume of signal input from CH1/2.
13. [PEAK] LED indicator light, it will light up when the input signal is too high.
14. [ECHO EFFECT] Controller, to adjust the Echo effect.
15. [AUX IN] 3.5mm jack, this is an auxiliary input, exible connectivity for a
variety of external audio devices. The volume can be controlled by external
audio devices or MAIN MIX controller.
16. This is an input select switch, when the switch is bounce up, the input signal is
from LINE IN. Press it down, the input signal is from USB/BT.
17. This is an output select switch, when the switch is bounced up, can be assigned
to MAIN MIX output. Press it down to assign to PHONES output.
18. [LINE/USB/BT] Controller, control the volume of LINE/USB/BT channel.
19. [PHONES] Controller, control the volume of earphones.
20. [MIC TO CH1] Jack, it is a 3.5mm input jack for microphone, the input audio is
sent to CH1.
21. [MIC TO CH2] Jack, it is a 3.5mm input jack for microphone, the input audio is
sent to CH2.
22. [PHONES] 3.5mm output jack, connect with earphones, it is supporting stereo
phone plug.
23. [CLIP L & R] LED, they will light up when the MAIN output signal is too high.
24. [MAIN MIX] Controller, used to adjust the volume of MAIN MIX and USB PORT
output.
www.PyleUSA.com
8
Page 9
USB 2.0 Terminal
Use a USB 2.0 cable (included with this
package) to connect the Local unit’s
USB Port to a USB port on the
computer. When connected to a
computer, it supplies power to the
mixer, and audio data can be sent
between mixer and computer.
It can also be used with a USB power
socket or USB power bank to supply
power to the mixer.
When using as external power supply, it must meet the following requirements:
• Output voltage: 4.8V to 5.2V
• Output current: 0.5A or even more
If you’re using it as USB power socket or USB power bank to supply power to the
mixer, you can’t transfer data and record as the unit should to be connected to a
computer.
WIRELESS BT CONNECTIVITY:
• Instantly Receives Wireless Music Streaming Audio
• Works with All of Your Favorite Devices
(iPhone, Android, Smartphones, iPad, Tablet, MP3 Player, etc.)
• Wireless BT Version: 5.0
• Wireless BT Network Name: ‘MP’
• Wireless BT Range: 50' Feet
www.PyleUSA.com
9
Page 10
PAD12MXUBT
2-Channel Wireless BT Streaming Mini Audio Mixer
Compact DJ Mixer with USB Audio Interface (+48V DC Phantom Power)
FEATURES:
• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Combo Jack (XLR+6.35mm) for MIC/LINE/GUITAR Inputs
• RCA Jacks for Stereo Input and Output
• 3.5mm Jack for Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis
WHAT'S IN THE BOX:
• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable
TECHNICAL SPECS:
• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 4.72'' x 3.95'' x 1.38'' –inches
www.PyleUSA.com
10
Page 11
PAD22MXUBT
2-Channel Wireless BT Streaming Mini Audio Mixer
Compact DJ Mixer with USB Audio Interface (+48V DC Phantom Power)
FEATURES:
• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Combo Jack (XLR+6.35mm) for MIC/LINE/GUITAR Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• 6.35mm Jacks for Stereo Input and Output
• 6.35mm Jack for Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis
WHAT'S IN THE BOX:
• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable
TECHNICAL SPECS:
• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 4.80'' x 4.19'' x 1.38'' -inches
www.PyleUSA.com
11
Page 12
PAD33MXUBT
3-Channel Wireless BT Streaming Mini Audio Mixer
1 Mono + 2 Stereo (Line In & 2-TK) Inputs, Compact DJ Mixer
with USB Audio Interface (+48V DC Phantom Power)
FEATURES:
• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Built-in Echo Effect
• Extremely Musical 2-band EQ & PAN on each Channel
• Combo Jack (XLR+6.35mm) for MIC/LINE Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• RCA Jacks for Stereo Input and Output
• 2-TK RCA Input Jacks
• 3.5mm Jacks for Microphone Input & Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis
WHAT'S IN THE BOX:
• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable
TECHNICAL SPECS:
• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 5.35'' x 3.95'' x 1.38'' -inches
www.PyleUSA.com
12
Page 13
PAD43MXUBT
4-Channel Wireless BT Streaming Mini Audio Mixer
2 Mono + 2 Stereo (Line In & 2-TK) Inputs, Compact DJ Mixer
with USB Audio Interface (+48V DC Phantom Power)
FEATURES:
• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Built-in Echo Effect
• Extremely Musical 2-band EQ & PAN on Each Channel
• Combo Jacks (XLR+6.35mm) for MIC/LINE Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• RCA Jacks for Stereo Input and Output
• 2-TK RCA Input Jacks
• 3.5mm Jacks for Microphone Input & Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis
WHAT'S IN THE BOX:
• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable
TECHNICAL SPECS:
• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 7W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 5.35'' x 5.13'' x 1.38'' -inches
www.PyleUSA.com
13
Page 14
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
Loading...